bulb NISSAN 300ZX 1984 Z31 Electrical System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 116, PDF Size: 3.42 MB
Page 16 of 116
CHARGING SYSTEM
Make sure "S ' termmal 8s con- IC-RG IC regulator
When reaching "Damaged
A C G.", remove
0 K. IC-alternator 16 In good condltlon nected COrreCtly
Trouble-Shooting
Before conducting an alternator test, make sure that the battery IS fully charged A 30-Volt voltmeter and
suitable test probes are necessary for the test The alternator can
be checked easily by referrmg to the
Inspection Table
Engine tdltng Lighting $witch "ON,, (Check light for operatlonl
WITH IC REGULATOR
bulb Replace and Proceed -
Wpth alternator side L terminal grounded, internal short occurs when + diode IS short-circuited @
Ignition witch "ON" cOnneCtor IS. (Check light Ll and ground for operatton1 L lead w~re Connect con-
I lH,TACHl nector IS LI far operation1 and ground F
I [Check Itght I for operation1
I (MITSUBISHI ' makel I - - - - - - - - - - - - -------- -
J
..........................
Contact poiitwe lead (+I of voltmeter on B
Lqht "OFF"
9
Engine speed 1,500 rpm
terminal and negative lead (-1 to L terminal
(Measure the "oltage acres "E" and "L"
only)
Contact tip of wlre with brush and attach wire to
alternator body -0 Light"0FF" -- OK
5) Terminals "S", "L", "BAT" and "E" are marked
on rear cover
of alternator.
Brush lift wire
SEL766D
EL-1 6
Page 37 of 116
EXTERIOR LAMP
-
Item
-
Headlamp
Au, iliary driving lamp
Front combination lamp
Front side marker lamp
Rear side marker lamp
Rear cornbination lamp
1-urn signal
StopITail
Elack-up
Lictme plate lamp
Interior lamp
Spot lamp
Rear (luggage) compartment
lamp
Door step lamp
Leg room lamp
-
-Stop and Tail Lamp Sensor Check,
0 Before checking, ensure that bulbs meet Wattage (W)
65,35
55
2718 34
34
2718
2718
27
40
10
a
34
5
2
soecif ications
STOP LAMP
Stop lamp switch on
Stop lamp on good order
stop lamp removed Approx 12 volts
Approx 2volt6
voltmeter
SEL170B
TAIL LAMP
Lighting switch on
Tad lamp mgood order
Tail lamp removed ~pprox. 12 vans
. Approx 2 volts
SEL1710
- Bulb Specifications
SAE trade
number
Hi3054
-
1157
158 158
1157 1157
1073
-
-
-
-
-
-
EL-37
Page 75 of 116
WARNING LAMPS AND CHIME
Diode Check
Check continuity using an ohmmeter
Diode
is functioning properly if test results are
as shown below
--I+-- 11 ,- Diode
Ohmmeter
NO continuity
@
SEL700D
DIGITAL TYPE COMBINATION METER
Diodes for warning lamps are located on the
panel where warning bulbsare fitted
For bulb check
For brake warning
7f For door warning
Far door warning
For tail lamp warning
For radmtor warning
Far 0, sensor warning
Far headlamp warning For brake warning
SEL701D
-~
NEEDLE TYPE COMBINATION METER
Diodes for warning lamps are built into the
Combination meter printed circuit
7- For 0, sensor warning
BRAKE DOOR FUEL
For bulb check
LAMP
SEL70ZD
--Warning Chime Check
A
SEL875D
EL-75