display NISSAN 300ZX 1984 Z31 Electrical System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 116, PDF Size: 3.42 MB
Page 46 of 116
METER AND GAUGES - Digital Type Combination Meter
Display Check
EL-46
Page 47 of 116
METER AND GAUGES - Digital Type Combination Meter
-
(+) (-) OFF
Display Check (Cont'd)
a Digital combination meter is provided with a
self-check function to determine whether or
not meter itself
is malfunctioning.
Test procedure
(1) While pushing trip reset switch A, switch igni-
tion switch from
"OFF" to "ON" Trip reset
switch
A should remain pushed in until self-
check operation start
(2) Meter starts to automatically perform self-
check. Segments for meters and gauges should
illuminate one after another.
(3) If any particular segment remains off, corn-
bination meter
itself is faulty.
ACC ON -Preparation for Trouble-shooting -
0
Approx
12v 0 ov ov
SEL665D
a
Remove instrument switch
a Remove cluster lid A
Remove nut which holds instrument switch
- Trouble-shooting
I Go to "Display check" I
1 NG
power source circuit unit
-IF' L-IF-NG
Replace meter and
gauge assembly
Check for loose
harness connector
Voltmeter terminals Ignition switch position
Ohmmeter terminals
Ignition Switch OFF
Continuity exists ground
a Disconnect meter harness connector as shown
below
.
SEL744D
-
EL-47
Page 48 of 116
METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont'd)
Replace meter
and gauge assembly
Speedometer does not operate
Go to "Display Check"
Check harness between
speed sensor and meter
OK
Go to "Power
Unit Check"
T T Replace meter Replace
and gauge assembly power Unit
Go to "Speed Sensor Signal Check" to check speed
sensor output
Go to "Display Check"
Go to "Power
Unit Check"
OK
Replace meter Replace
and gauge assembly power unit
.
1 Check ignition coil circuit I
and gauge assen
1'
T lNG Replace meter Check resistor, ignition
and
gauge assembly coil and power transistor
(Refer to ignition system)
1 Disconnect meter harness connector
2
3 Check terminal voltage between @ and
(white)
Turn ignition switch to
"ON".
0
VOltmeter SEL6660
EL-48
Page 49 of 116
METER AND GAUGES - Digital Type Combination Meter
Trouble-st
Torque meter does not operate
1 Go to "Display Check" I
Go to "Power Unit Check"
v
Replace meter Replace
and gauge assembly power unit
I
I Check boost sensor circuit I
boost sensor and meter boost
sensor
1 Disconnect meter harness connector
2 Connect vacuum pump gauge to boost
3
4
(white)
sensor vacuum hose
Turn the ignition switch to "ON"
Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltage
across
0 and
Vacuum -
~eep harness connected
J wu 1 3v at-53 3kPa 1-400 mmH
SEL667 Voltmeter -15 75 mHg) '
rg (Cont'd)
Main fuel gauge does not operate
I
Go to "Display Check"
Go to "Power Unit Check"
Replace meter Replace
and gauge power unit
assembly
Check fuel tank main gauge clrcult
I OK
Replace meter
and gauge
assembly Go to "Fuel tank
gauge check"
.
Check harness between Replace fuel
fuel tank gauge and meter
tank gauge unit
1 Disconnect meter harness Connector
(black)
Turn ignition switch to
"OFF" 2
3 Measure resistance between @ and @
e
Ohmmeter SEL6680
EL-49
Page 50 of 116
METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont'd)
Fuel residue
Sub fuel gauge (digital display1 does not operate
Go to "Display Check"
Go to "Power Unit Check"
Replace meter Replace
and gauge power unit
assembly
Resistance
Check harness
Check fuel tank sub gauge circuit
Go to "Fuel Tank
Gauge Check"
OK
v T
Replace Check harness between Replace meter
fuel tank fuel tank gauge and meter and gauge
gauge unit assembly
FUEL INJECTION PULSE CIRCUIT
CHECK
1 Disconnect meter harness connector
(black)
2. Turn ignition switch to "ON"
3 Check for voltage across @$ and 0.
Voimeter SE L669 t
FUEL TANK SUB GAUGE CIRCUIT
CHECK
1 Turn ignition switch to "OFF"
2. Measure resistance between 0 and 0.
Ohmmeter
Ignition switch- OFF
More than ZOQ Less than 4R
SEL670D
EL-50
Page 51 of 116
METER AND GAUGES - Digital Type Combination Meter
Trou ble-sho
Go to "Display Check"
OK
Go to "Power Unit Check"
T
Replace meter and
gauge assembly Replace power unit
T Replace meter and gauge assembly
ng (Cont'd)
Only water temp gauge does not operate
I
Go to "Display Check"
T
OK
Replace meter and
gauge assembly
Check water temp sensor (thermistor) Circuit
OK NG
Replace meter
and gauge
assembly
Check harness between Replace
thermistor and meter thermistor
1 Disconnect meter harness connector
2
3
(black)
Turn ignition swltch to "OFF"
Measure resistance between 0 and @
!'W I 1 Ohmmeter
ignition switch - OFF
Resistance
70CI or more
6O'C or more Approx 10 - 70R
SEL6710
EL-51
Page 52 of 116
METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont’d)
Go to “Displav Check”
ING OK
Replace meter and
gauge assembly
v
Check oil pressure sensor circuit
OK NG
Go to “Oil Pressure
Sensor Check” Replace meter
and gauge
assembly
Check harness between Replace oil
oil pressure sensor and meter pressure
sensor
1 Disconnect meter harness connector
(black)
2 Measure resistance between @ and @
when engine stopping and running
Ohmmeter
Engine Resistance
Approx 75R or more
Idling Approx 60R or less
SEL672D
“Trip”, ”Ave speed” and “Dist to empty” meters
1 Go to ”Display Check” 1
Go to “Power Unit Check”
Replace trip Replace power unit
meter assembly
Only “Ave speed” meter does not operate
I
I Go to “Display Check“ I
lNG
OK
Replace trip
meter assembly
I Check clock for proper operation I
Check harness between Replace clock
clock and meter
I OK v
Replace trip meter assembly
Page 53 of 116
METER AND GAUGES - Digital Type Combination Meter
Power Unit Check
Voltmeter
terminal
(f) (-)
E -
-%; 0
0
@I
__
@
9
0
0
Remove power unit with harness connected
Perform voltage and continuity tests Refer to
chart below
I Voltage
[VI
Approx 12
Approx 5
Approx 16
Approx 5
Approx 22
Approx 285
Turn ignition switch to "ON"
1 - 1 More than 6
Remarks
Check when no
display appears
For speedometer
For tachometer
For Temp,
Oil, Volt
sause
For Fuel gauge
For "Trip", "Ave
speed"
& "Dirt to
empty" meter
Turn ignition switch to "OFF"
Ohmmeter
Continuity Remarks
Check when no
ground display appears
If specified voltage or continuity is not produced,
replace power unit.
- Boost Sensor Check
1 Connect vacuum pump gauge to boost sensor
vacuum hose
2 Disconnect harness connector from boost
sensor and connect battery and voltmeter
as
shown
3 Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltages
Approx.
2.2V at 0 kPa (0 mmHg, 0 inHg)
(Atmospheric pressure)
Approx.
1 3V
at -53.3 kPa (-400 mmHg, -15 75 inHg)
vacuum pump gauge
SEL674D
EL-53
Page 59 of 116
METER AND GAUGES -Digital Type Combination Gauge
Trouble-shooting
(+)
v
Check power supply circuit for combination
gauge
(-1
l°K 1 NG
Replace combination gauge Check harness
Voltmeter terminal I Ignition switch position
Approx Approx
@ I 03 I OV I 12v ! 12v
Continuity exists @ I gK:d I
Remove radio and A/C control assembly from
center console and remove combination gauge
with harness connected
Check from harness rtde
SEL681D
Display illumination will not darken when light
1 switch is "ON"
I Check light switch circuit for combination gauge I
1 Remove radio and A/C control assembly
and remove combination gauge with har-
ness connected.
Turn ignition switch to
"OFF"
Turn light switch to "ON"
Measure voltage across @ and @
2
3
4
Ignition switch - 0
ht switch - ON
SEL682D L
EL-59
Page 60 of 116
METER AND GAUGES -Digital Type Combination Gauge
,- Trouble-shooting (Cont'd)
Compass will not indicate direction in which vehicle is being driven COMPASS
I
Face vehicle toward the North to make sure arrow points to "N"
Display deviates
by one graduation
. more graduations
Display deviates by two or
. 1 SIOWI~ turn volume 0 until arrow moves from
@ (0) to @ (@I Thenslowlyreturn
volume
@ until arrow points to point @
When arrow deviates toward West, move switch
@ to (+),when it deviates toward the East,
move switch to
(-) Return switch @ to
Neutral when arrow stays between points
@)
and @
I Face vehicle toward the East to make sure arrow points to "E" 1
Display deviates
SIOWIV turn volume @ until arrow moves from
(Q (0) to @ (@I Then slowly return
volume
@ until arrow points to point @
1 Display deviates by two or
. more graduations
switch @to (+I, when it deviates toward the
South, move switch
to (4 Return switch @
to Neutral when arrow stays between points
(Q and 0
I Again face vehicle toward the North to make sure arrow points to "N" 1
Direction sensor amplifier (Located on luggage compartment R H 1 , ,
Dirplav
SEL683D SEL684D
EL-60