oil type NISSAN 300ZX 1984 Z31 Electrical System Workshop Manual

METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont'd)
Replace meter
and gauge assembly
Speedometer does not operate
Go to "Display Check"
Check harness between
speed sensor and meter
OK
Go to "Power
Unit Check"
T T Replace meter Replace
and gauge assembly power Unit
Go to "Speed Sensor Signal Check" to check speed
sensor output
Go to "Display Check"
Go to "Power
Unit Check"
OK
Replace meter Replace
and gauge assembly power unit
.
1 Check ignition coil circuit I
and gauge assen
1'
T lNG Replace meter Check resistor, ignition
and
gauge assembly coil and power transistor
(Refer to ignition system)
1 Disconnect meter harness connector
2
3 Check terminal voltage between @ and
(white)
Turn ignition switch to
"ON".
0
VOltmeter SEL6660
EL-48

METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont’d)
Go to “Displav Check”
ING OK
Replace meter and
gauge assembly
v
Check oil pressure sensor circuit
OK NG
Go to “Oil Pressure
Sensor Check” Replace meter
and gauge
assembly
Check harness between Replace oil
oil pressure sensor and meter pressure
sensor
1 Disconnect meter harness connector
(black)
2 Measure resistance between @ and @
when engine stopping and running
Ohmmeter
Engine Resistance
Approx 75R or more
Idling Approx 60R or less
SEL672D
“Trip”, ”Ave speed” and “Dist to empty” meters
1 Go to ”Display Check” 1
Go to “Power Unit Check”
Replace trip Replace power unit
meter assembly
Only “Ave speed” meter does not operate
I
I Go to “Display Check“ I
lNG
OK
Replace trip
meter assembly
I Check clock for proper operation I
Check harness between Replace clock
clock and meter
I OK v
Replace trip meter assembly

METER AND GAUGES - Digital Type Combination Meter
Power Unit Check
Voltmeter
terminal
(f) (-)
E -
-%; 0
0
@I
__
@
9
0
0
Remove power unit with harness connected
Perform voltage and continuity tests Refer to
chart below
I Voltage
[VI
Approx 12
Approx 5
Approx 16
Approx 5
Approx 22
Approx 285
Turn ignition switch to "ON"
1 - 1 More than 6
Remarks
Check when no
display appears
For speedometer
For tachometer
For Temp,
Oil, Volt
sause
For Fuel gauge
For "Trip", "Ave
speed"
& "Dirt to
empty" meter
Turn ignition switch to "OFF"
Ohmmeter
Continuity Remarks
Check when no
ground display appears
If specified voltage or continuity is not produced,
replace power unit.
- Boost Sensor Check
1 Connect vacuum pump gauge to boost sensor
vacuum hose
2 Disconnect harness connector from boost
sensor and connect battery and voltmeter
as
shown
3 Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltages
Approx.
2.2V at 0 kPa (0 mmHg, 0 inHg)
(Atmospheric pressure)
Approx.
1 3V
at -53.3 kPa (-400 mmHg, -15 75 inHg)
vacuum pump gauge
SEL674D
EL-53

METER AND GAUGES - Digital Type Combination Meter
Fuel Tank Gauge Check
For removal, refer to FE section
Ohmmeter terminal Float
Main gauge
Resistance value
Approx 10 - 20Q
Approx 480 - 520Q
Approx 100 - 1 1 OQ
Approx 4Q or below
Approx
870.930Q
Sub gauge
SEL675D
SEL676D
-Water Temp Sensor Check -
Cylinder head R H side
SEL677D
-Oil Pressure Sensor Check -
-
011 filter 7 \
SEL678D
Ohmmeter
terminal With engine With engine
stopped 1 running (idling)
ca On
+I;'''' I More than 74Q I Less than 60.Q
EL-56

METER AND GAUGES -Needle Type Combination Meter
Combination Meter
pj
0, SENSO
35 36 31
1 TACHO-
METER
BBpgBW *Em 8EAR
FUEL BELT DOOR BRAKE CHARGE OIL RADIATO HEAD- STOP&
COOLANl LAMP TAIL LAMP
0 32 -- a: "E NATION 30
ILLUMI-
0 33 -U 18 19 20 s;14 15 5 23
24 2. 29 1 3 4 11
SEL690D
EL-65

METER AND GAUGES -Needle Type Combination Gauge
Oil Temp. Sensor Check
1 Warm up engine
2
3
Stop engine and turn ignition switch OFF
Check resistance of
oil temp sensor
SEL695D
- Boost Gauge Trimmer Adjustment -
When boost gauge does not give proper reading,
adjust
0 kPa (0 mmHg, 0 inHg) point with the
trimmer located on interlor upper wall of glove
box
Use a screwdriver to adjust trimmer
For checking oil pressure sensor and boost
sensor, refer to pages EL-53 and 56
EL-70