length NISSAN 300ZX 1984 Z31 Rear Suspension Workshop Manual

DRIVE SHAFT-'"Tripod-Tripod" Type
Assemb
Install hold joint boot assembly
SFA395
Pack with grease
Specified amount of grease
185 - 195 g (6.52 - 6.88 02)
Set boot so that it does not swell or deform
when
its length is "L".
Length "L" 111 5 mm (4 39 on1
SRA452
[Cont'd)
DIFFERENTIAL CARRIER SIDE
CAUTION.
When replacing housing ring or housing sub-
assembly, always replace them as a set.
Bend the edge over along the entire circumfer-
ence.
Bend
the edge at two positions (180" apart) and
ensure that housing cover
does not rattle.
Place a board
on housing cover to prevent it from
being scratched.
~~~340
0 Install new boot band and hold joint boot
Be careful
not to scratch boot with drive shaft
serration
0 Install spider assembly Refer to WHEEL SIDE
0 Pack with grease
Specified amount of grease:
Place hold joint boot assembly so that its
assembly onto drive shaft
155 - 165 g (5.47 - 5.82 OZ)
flange is in vise.
Do not place any other part of hold joint boot
assembly on a vise.
Insert housing sub-assembly into place.
Bend
the edge over along the entire circumfer-
ence
RA-10

DRIVE SHAFT--"Tripod-Tripod" Type
Assem bl1
Bend the edge at two positions (180" apart) and
ensure that housing sub-assembly does not rattle.
Place
a board on housing sub-assembly to prevent
it from being scratched.
SRA341
e Apply sealant
Cont'd)
e Set boot so that it does not swell or deform
when
its length is "L"
Length "L" 92 5 mm 13 642 m)
IL1
SRA453
RA-11

SERVICE DATA AND SPECIFICATIONS (S.D.S.)
Coil diameter mm Inn1
mm 1,”) Free length
General Specifications
I I I
11014331
364114331 370 11457) 364114331 370 114 57) 376 114801
SUSPENSION
VG30E VG30ET
Vehicle model 2/2+2 seater 2 seater 2+2 seater
SF GL GL GL-L
Suspension type Semi-trailing arm type independent rear suspension
Adjustable
coll sprmg Wire diameler mmlinl 128105041 130105121 128105041
Non-adjustable
13 0 (0 5121 ~~
~
Pmon diameter mm lml 32 - 32 1 (1 260 - 1 2641 25 - 25 1 (0 984.0 9881
24 5 I2 5, 1401 Spring wnnant
Nlmm Ikdmm. Ib/cnl
Pinon rod diameter mm 11”) 22 IO 87)
Identification coloi
125(04921
Red x 1 Yellow x 2 Yellow x 1
Yellow x 2
Cylinder diameter mm (on1
Damping force
[at 0 3 m I1 0 ftirec II
Yellow x 1
Yellow x 2
486 I1 913) 38 1 (1 5001
Firm Normal Soft
White x 1
I White x 2 ~
Shock
absorber
Type
609 3 123 991/392 5 115 451
588 160,132f
294 130,661
I ~ ~~ Stabilizer tube
diameter Outer mm (ml 22 2 10 874)
Inner mm (in) I 17 0 IO 6691
RA-20

SERVICE DATA AND SPECIFICATIONS (S.D.S.)
-General Specifications (Cont'd)-
DRIVE SHAFT
Engine
F
Model
Joint type Dlfferenrlal carrier ride
Wheel side
Maximum winding degree
Dcfferential carrier $#de
Wheel ride
Length "L" mm linl
Maximum [LeftIRightl
Minimum [Left/Rightl
VG30E
2T82S
Tripod
Tripod
18 3"
1 5"
464 5 118 291/
475
5 118 721
407 I16
0211 418 I16461
VG30ET
BF90DS90
Barfield
Double offset
40'
20-
449 5 117 7011
461
5 118 171
409
5 (16 1211
421 5 116 591
rL-
Grease
Name
Capacity 9 lo21
Nisran genuine
grease
or
equivalent
Wheel side
185- 195
I6 52 - 6 881
Differential
carrier side
155-165
15 47 - 5 821
d
SRA473
Nirsan genubne
grease or
equivalent
115-155
I4
06 -5 471
Inspection and Adjustment -
Wheel alignment (Unladen*l)
Camber degree -1'55 to -25 -
mm On1 -2 to 2 1-0 08 to 0 081 Toe-," degree -11'10 11'
'1 Tankful of fuel. radiator coolant and englne 011 full
Spare
tire, jack, hand took, mars ~n designed p~sitlon
Rear axle shaft
LerrthanO7 17.611 Wheel bearing preload
N m lkgcm. in-lbl
Lessthan120611 23,2711 Wheel bearing preload at hub bdt
N lkg, Ibl
Less than 0 3 IO 0121 Rear axle shaft end play
mm Id - A 5582-5588
Dtrtmce piece length
B 5592-5598
C 5602-5608
(2 1976.2 20001
mm
Id I2 2016.2 20391
I2 2055 - 2 20791
RA-21