check transmission fluid NISSAN 350Z 2007 Z33 Automatic Transmission Workshop Manual

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: 2006 November2007 350Z
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for Battery Service ................................ 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ....................................... 11
A/T FLUID ................................................................. 12
Changing A/T Fluid ................................................ 12
Checking A/T Fluid ................................................. 12
A/T Fluid Cooler Cleaning ...................................... 14
A/T CONTROL SYSTEM .......................................... 17
Cross-sectional View .............................................. 17
Shift Mechanism ..................................................... 18
TCM Function ......................................................... 29
CAN Communication .............................................. 30
Input/Output Signal of TCM .................................... 30
Line Pressure Control ............................................ 31
Shift Control ........................................................... 32
Lock-up Control ...................................................... 34
Engine Brake Control ............................................. 35
Control Valve .......................................................... 35
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 37
Introduction ............................................................ 37
OBD-II Function for A/T System ............................. 37
One or Two Trip Detection Logic of OBD-II ............ 37
OBD-II Diagnostic Trouble Code (DTC) ................. 37
Malfunction Indicator Lamp (MIL) ........................... 39
TROUBLE DIAGNOSIS ............................................ 40
DTC Inspection Priority Chart ................................ 40
Fail-safe ................................................................. 40
How to Perform Trouble Diagnosis for Quick and Accurate Repair ...................................................... 42
A/T Electrical Parts Location .................................. 47
Circuit Diagram ....................................................... 48
Inspections Before Trouble Diagnosis .................... 49
Check Before Engine is Started .............................. 53
Check at Idle ........................................................... 53
Cruise Test — Part 1 .............................................. 55
Cruise Test — Part 2 .............................................. 57
Cruise Test — Part 3 .............................................. 58
Vehicle Speed at When Gears Shifting Occurs ...... 58
Vehicle Speed at Which Lock-up Occurs/Releases ... 58
Symptom Chart ....................................................... 59
TCM Input/Output Signal Reference Values ........... 83
CONSULT-III Function (TRANSMISSION) ............. 84
Diagnostic Procedure Without CONSULT-III .......... 92
DTC U1000 CAN COMMUNICATION LINE .............. 94
Description .............................................................. 94
On Board Diagnosis Logic ...................................... 94
Possible Cause ....................................................... 94
DTC Confirmation Procedure ................................. 94
Wiring Diagram — AT — CAN ................................ 95
Diagnostic Procedure ............................................. 96
DTC P0615 START SIGNAL CIRCUIT ..................... 97
Description .............................................................. 97
CONSULT-III Reference Value ............................... 97
On Board Diagnosis Logic ...................................... 97
Possible Cause ....................................................... 97
DTC Confirmation Procedure ................................. 97
Wiring Diagram — AT — STSIG ............................ 98
Diagnostic Procedure ............................................. 99
DTC P0700 TCM .....................................................101
Description ............................................................101
On Board Diagnosis Logic ....................................101
Possible Cause .....................................................101
DTC Confirmation Procedure ...............................101
Diagnostic Procedure ...........................................101
DTC P0705 PARK/NEUTRAL POSITION SWITCH .102
Description ............................................................102
CONSULT-III Reference Value .............................102
On Board Diagnosis Logic ....................................102

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z Description ........................................................... 145
CONSULT-III Reference Value ............................. 145
On Board Diagnosis Logic ................................... 145
Possible Cause .................................................... 145
DTC Confirmation Procedure ............................... 145
Diagnostic Procedure ........................................... 146
DTC P1757 FRONT BRAKE SOLENOID VALVE .. 147
Description ........................................................... 147
CONSULT-III Reference Value ............................. 147
On Board Diagnosis Logic ................................... 147
Possible Cause .................................................... 147
DTC Confirmation Procedure ............................... 147
Diagnostic Procedure ........................................... 148
DTC P1762 DIRECT CLUTCH SOLENOID VALVE . 149
Description ........................................................... 149
CONSULT-III Reference Value ............................. 149
On Board Diagnosis Logic ................................... 149
Possible Cause .................................................... 149
DTC Confirmation Procedure ............................... 149
Diagnostic Procedure ........................................... 150
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE ................................................. 151
Description ........................................................... 151
CONSULT-III Reference Value ............................. 151
On Board Diagnosis Logic ................................... 151
Possible Cause .................................................... 151
DTC Confirmation Procedure ............................... 151
Diagnostic Procedure ........................................... 152
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE ..................................................................... 153
Description ........................................................... 153
CONSULT-III Reference Value ............................. 153
On Board Diagnosis Logic ................................... 153
Possible Cause .................................................... 153
DTC Confirmation Procedure ............................... 153
Diagnostic Procedure ........................................... 154
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION ................................................. 155
Description ........................................................... 155
CONSULT-III Reference Value ............................. 155
On Board Diagnosis Logic ................................... 155
Possible Cause .................................................... 155
DTC Confirmation Procedure ............................... 155
Diagnostic Procedure ........................................... 156
DTC P1815 MANUAL MODE SWITCH .................. 157
Description ........................................................... 157
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 157
On Board Diagnosis Logic ................................... 157
Possible Cause .................................................... 157
DTC Confirmation Procedure ............................... 157
Wiring Diagram — AT — MMSW ......................... 158
Diagnostic Procedure ........................................... 160
Component Inspection ......................................... 161
MAIN POWER SUPPLY AND GROUND CIRCUIT . 162
Wiring Diagram — AT — MAIN ............................ 162
Diagnostic Procedure ........................................... 163
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ........................... 166CONSULT-III Reference Value .............................166
Diagnostic Procedure ...........................................166
BRAKE SIGNAL CIRCUIT ......................................167
CONSULT-III Reference Value .............................167
Diagnostic Procedure ...........................................167
A/T INDICATOR CIRCUIT .......................................168
Description ............................................................168
CONSULT-III Reference Value .............................168
Diagnostic Procedure ...........................................168
TROUBLE DIAGNOSIS FOR SYMPTOMS ............169
Wiring Diagram — AT — NONDTC ......................169
A/T Check Indicator Lamp Does Not Come On ....172
Engine Cannot Be Started in “P” or “N” Position ..173
In “P” Position, Vehicle Moves When Pushed ......173
In “N” Position, Vehicle Moves ..............................174
Large Shock (“N” to “D” Position) .........................175
Vehicle Does Not Creep Backward in “R” Position .177
Vehicle Does Not Creep Forward in “D” Position . 179
Vehicle Cannot Be Started from D
1 ......................181
A/T Does Not Shift: D
1 → D2 ................................183
A/T Does Not Shift: D
2 → D3 ................................185
A/T Does Not Shift: D
3 → D4 ................................187
A/T Does Not Shift: D
4 → D5 ................................189
A/T Does Not Lock-up ..........................................191
A/T Does Not Hold Lock-up Condition ..................193
Lock-up Is Not Released ......................................194
Engine Speed Does Not Return to Idle ................195
Cannot Be Changed to Manual Mode ..................196
A/T Does Not Shift: 5th Gear → 4th Gear ............196
A/T Does Not Shift: 4th Gear → 3rd Gear ............198
A/T Does Not Shift: 3rd Gear → 2nd Gear ...........199
A/T Does Not Shift: 2nd Gear → 1st Gear ...........201
Vehicle Does Not Decelerate by Engine Brake ....202
SHIFT CONTROL SYSTEM ....................................204
Control Device Removal and Installation ..............204
Control Rod Removal and Installation ..................205
Adjustment of A/T Position ...................................206
Checking of A/T Position ......................................206
A/T SHIFT LOCK SYSTEM ....................................207
Description ............................................................207
Shift Lock System Electrical Parts Location .........207
Wiring Diagram — AT — SHIFT ...........................208
Diagnostic Procedure ...........................................209
KEY INTERLOCK CABLE ......................................212
Components .........................................................212
Removal and Installation ......................................213
ON-VEHICLE SERVICE ..........................................215
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 ...............................................................215
Parking Components ............................................227
Rear Oil Seal ........................................................234
Revolution Sensor ................................................235
AIR BREATHER HOSE ..........................................241
Removal and Installation ......................................241
TRANSMISSION ASSEMBLY ................................242
Removal and Installation ......................................242
OVERHAUL ............................................................246
Components .........................................................246

DTC P0700 TCM
AT-101
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
DTC P0700 TCMPFP:31036
DescriptionNCS0002T
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls A/T.
On Board Diagnosis LogicNCS0002U

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0700 TCM” with CONSULT-III is detected when TCM is malfunctioning.
Possible CauseNCS0002V
TCM.
DTC Confirmation ProcedureNCS0002W
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON.
2. Select “ECU INPUT SIGNALS” or “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION”
with CONSULT-III.
3. Touch “START”.
4. Start engine.
5. Run engine for at least 2 consecutive seconds at idle speed.
6. If DTC is detected, go to AT- 1 0 1 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-III”.
Diagnostic ProcedureNCS0002X
1. CHECK DTC
With CONSULT-III
1. Turn ignition switch ON.
2. Select “SELF DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.
3. Touch “ERASE”.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Perform AT- 1 0 1 , "
DTC Confirmation Procedure" .
Is the
“TCM” displayed again?
YES >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NO >>INSPECTION END

DTC P0717 TURBINE REVOLUTION SENSOR
AT-107
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS001A0
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Vehicle start and read out the value of “TURBINE REV”.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 0 6 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name Condition Display value
TURBINE REVDuring driving
(lock-up ON)Approximately matches the engine speed.

DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)
AT-111
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0003B
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “VHCL/S SE-A/T” while driving. Check the value changes according to driving
speed.
OK or NG
OK >> GO TO 6.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK SUB-HARNESS
1. Remove control valve with TCM. Refer to AT- 2 1 5 , "
Control Valve with TCM and A/T Fluid Temperature
Sensor 2" .
2. Disconnect park/neutral position switch connector and TCM connector.
3. Check continuity between park/neutral position switch connector
terminals and TCM connector terminals.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK >> GO TO 5.
NG >> Replace open circuit or short to ground and short to power in harness or connectors.
Item name Condition Display value
VHCL/S SE-A/T During drivingApproximately matches the speedometer
reading.
Item Connector Terminal Continuity
Park/neutral position switch connector F505 8
Ye s
TCM connector F503 20
Park/neutral position switch connector F505 9
Ye s
TCM connector F503 17
Park/neutral position switch connector F505 10
Ye s
TCM connector F503 16
SCIA5458E

AT-114
DTC P0725 ENGINE SPEED SIGNAL
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0003H
1. CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to AT- 8 6 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 9 2 , "Diagnostic Procedure
Without CONSULT-III" .
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT- 9 4 , "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.
2. CHECK DTC WITH TCM
With CONSULT-III
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. While monitoring engine speed, check for engine speed change corresponding to wide-open throttle posi-
tion signal.
OK or NG
OK >> GO TO 3.
NG >> Check the ignition signal circuit. Refer to EC-698, "
IGNITION SIGNAL" .
3. CHECK DTC
Perform AT- 11 3 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
Item name Condition Display value
ENGINE SPEED Engine running Closely matches the tachometer reading.

DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
AT-125
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVEPFP:31940
DescriptionNCS0003I

Torque converter clutch solenoid valve is activated, with the gear in D4 , D5 , M2 , M3 , M4 and M5 by the
TCM in response to signals sent from the vehicle speed sensor and accelerator pedal position sensor
(throttle position sensor). Torque converter clutch piston operation will then be controlled.

Lock-up operation, however, is prohibited when A/T fluid temperature is too low.

When the accelerator pedal is depressed (less than 1.0/8) in lock-up condition, the engine speed should
not change abruptly. If there is a big jump in engine speed, there is no lock-up.
CONSULT-III Reference ValueNCS0003J
On Board Diagnosis LogicNCS0003K

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0740 TCC SOLENOID/CIRC” with CONSULT-III or 3rd judgment flicker without
CONSULT-III is detected under the following conditions.
–When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–When TCM detects as irregular by comparing target value with monitor value.
Possible CauseNCS0003L

Torque converter clutch solenoid valve

Harness or connectors
(Solenoid circuit is open or shorted.)
DTC Confirmation ProcedureNCS0003M
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON.
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III
and check monitor “VHCL/S SE-A/T”, “ACCELE POSI” and “SLCT LVR POSI”.
3. Touch “START”.
4. Start engine and maintain the following conditions for at least 5 consecutive seconds.
VHCL/S SE-A/T: 80 km/h (50 MPH) or more
ACCELE POSI: 0.5/8 – 1.0/8
SLCT LVR POSI: “D” position
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
5. If DTC is detected go to AT- 1 2 6 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-III”.
Item name Condition Display value (Approx.)
TCC SOLENOID Lock-up is active 0.4 – 0.6 A

AT-126
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0003N
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “TCC SOLENOID” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 2 5 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name ConditionDisplay value
(Approx.)
TCC SOLENOID Lock-up is active 0.4 – 0.6 A

AT-128
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0003T
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “TCC SOLENOID” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 2 7 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name ConditionDisplay value
(Approx.)
TCC SOLENOID Lock-up is active 0.4 – 0.6 A

AT-130
DTC P0745 LINE PRESSURE SOLENOID VALVE
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0003Z
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “LINE PRES SOL” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 2 9 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name ConditionDisplay value
(Approx.)
LINE PRES SOL During driving 0.2 – 0.6 A