heater NISSAN 350Z 2007 Z33 Engine Control Workshop Manual

EC-2Revision: 2006 November2007 350Z DENT .......................................................................141
Description ............................................................141
Diagnostic Procedure ...........................................141
POWER SUPPLY AND GROUND CIRCUIT ...........142
Wiring Diagram .....................................................142
Diagnostic Procedure ...........................................145
Ground Inspection ................................................150
DTC U1000, U1001 CAN COMMUNICATION LINE .151
Description ............................................................151
On Board Diagnosis Logic ....................................151
DTC Confirmation Procedure ...............................151
Wiring Diagram .....................................................152
Diagnostic Procedure ...........................................153
DTC U1010 CAN COMMUNICATION .....................154
Description ............................................................154
On Board Diagnosis Logic ....................................154
DTC Confirmation Procedure ...............................154
Diagnostic Procedure ...........................................155
DTC P0011, P0021 IVT CONTROL ........................156
Description ............................................................156
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................156
On Board Diagnosis Logic ....................................157
DTC Confirmation Procedure ...............................157
Diagnostic Procedure ...........................................158
Component Inspection ..........................................159
Removal and Installation ......................................159
DTC P0014 P0024 EVT CONTROL ........................160
Description ............................................................160
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................160
On Board Diagnosis Logic ....................................161
DTC Confirmation Procedure ...............................161
Diagnostic Procedure ...........................................162
Component Inspection ..........................................164
Removal and Installation ......................................164
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ..................................................................165
Description ............................................................165
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................165
On Board Diagnosis Logic ....................................165
DTC Confirmation Procedure ...............................165
Wiring Diagram .....................................................166
Diagnostic Procedure ...........................................170
Component Inspection ..........................................172
Removal and Installation ......................................172
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .173
Description ............................................................173
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................173
On Board Diagnosis Logic ....................................173
DTC Confirmation Procedure ...............................174
Wiring Diagram .....................................................175
Diagnostic Procedure ...........................................179
Component Inspection ..........................................181
Removal and Installation ......................................182
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .....................................................................183Component Description ........................................183
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................183
On Board Diagnosis Logic ....................................183
DTC Confirmation Procedure ................................183
Wiring Diagram .....................................................184
Diagnostic Procedure ............................................188
Component Inspection ..........................................189
Removal and Installation .......................................189
DTC P0078 P0084 EVT CONTROL MAGNET
RETARDER .............................................................190
Component Description ........................................190
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................190
On Board Diagnosis Logic ....................................190
DTC Confirmation Procedure ................................190
Wiring Diagram .....................................................191
Diagnostic Procedure ............................................195
Component Inspection ..........................................196
Removal and Installation .......................................196
DTC P0101, P010B MAF SENSOR ........................197
Component Description ........................................197
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................197
On Board Diagnosis Logic ....................................197
DTC Confirmation Procedure ................................198
Overall Function Check .........................................198
Wiring Diagram .....................................................200
Diagnostic Procedure ............................................203
Component Inspection ..........................................206
Removal and Installation .......................................207
DTC P0102, P0103, P010C, P010D MAF SENSOR .208
Component Description ........................................208
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................208
On Board Diagnosis Logic ....................................208
DTC Confirmation Procedure ................................209
Wiring Diagram .....................................................210
Diagnostic Procedure ............................................213
Component Inspection ..........................................216
Removal and Installation .......................................217
DTC P0112, P0113 IAT SENSOR ............................218
Component Description ........................................218
On Board Diagnosis Logic ....................................218
DTC Confirmation Procedure ................................218
Wiring Diagram .....................................................219
Diagnostic Procedure ............................................220
Component Inspection ..........................................222
Removal and Installation .......................................222
DTC P0117, P0118 ECT SENSOR ..........................223
Component Description ........................................223
On Board Diagnosis Logic ....................................223
DTC Confirmation Procedure ................................224
Wiring Diagram .....................................................225
Diagnostic Procedure ............................................226
Component Inspection ..........................................228
Removal and Installation .......................................228
DTC P0122, P0123, P0227, P0228 TP SENSOR ...229
Component Description ........................................229

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2006 November2007 350Z Description ........................................................... 628
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 628
On Board Diagnosis Logic ................................... 628
DTC Confirmation Procedure ............................... 628
Wiring Diagram .................................................... 629
Diagnostic Procedure ........................................... 630
Component Inspection ......................................... 632
DTC P2122, P2123 APP SENSOR ........................ 633
Component Description ........................................ 633
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 633
On Board Diagnosis Logic ................................... 633
DTC Confirmation Procedure ............................... 634
Wiring Diagram .................................................... 635
Diagnostic Procedure ........................................... 637
Component Inspection ......................................... 640
Removal and Installation ...................................... 640
DTC P2127, P2128 APP SENSOR ........................ 641
Component Description ........................................ 641
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 641
On Board Diagnosis Logic ................................... 641
DTC Confirmation Procedure ............................... 642
Wiring Diagram .................................................... 643
Diagnostic Procedure ........................................... 645
Component Inspection ......................................... 648
Removal and Installation ...................................... 649
DTC P2138 APP SENSOR ..................................... 650
Component Description ........................................ 650
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 650
On Board Diagnosis Logic ................................... 650
DTC Confirmation Procedure ............................... 651
Wiring Diagram .................................................... 652
Diagnostic Procedure ........................................... 654
Component Inspection ......................................... 658
Removal and Installation ...................................... 658
DTC P2A00, P2A03 A/F SENSOR 1 ...................... 659
Component Description ........................................ 659
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 659
On Board Diagnosis Logic ................................... 659
DTC Confirmation Procedure ............................... 660
Wiring Diagram .................................................... 661
Diagnostic Procedure ........................................... 665
Removal and Installation ...................................... 670
ASCD BRAKE SWITCH ......................................... 671
Component Description ........................................ 671
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... 671
Wiring Diagram .................................................... 672
Diagnostic Procedure ........................................... 675
Component Inspection ......................................... 680ASCD INDICATOR ..................................................681
Component Description ........................................681
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................681
Wiring Diagram .....................................................682
Diagnostic Procedure ...........................................683
ELECTRICAL LOAD SIGNAL ................................684
Description ............................................................684
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................684
Diagnostic Procedure ...........................................684
FUEL INJECTOR ....................................................686
Component Description ........................................686
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................686
Wiring Diagram .....................................................687
Diagnostic Procedure ...........................................688
Component Inspection ..........................................690
Removal and Installation ......................................690
FUEL PUMP ............................................................691
Description ............................................................691
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................691
Wiring Diagram .....................................................692
Diagnostic Procedure ...........................................693
Component Inspection ..........................................697
Removal and Installation ......................................697
IGNITION SIGNAL ..................................................698
Component Description ........................................698
Wiring Diagram .....................................................699
Diagnostic Procedure ...........................................704
Component Inspection ..........................................708
Removal and Installation ......................................709
REFRIGERANT PRESSURE SENSOR ..................710
Component Description ........................................710
Wiring Diagram .....................................................711
Diagnostic Procedure ...........................................712
Removal and Installation ......................................715
MIL AND DATA LINK CONNECTOR ......................716
Wiring Diagram .....................................................716
SERVICE DATA AND SPECIFICATIONS (SDS) ....718
Fuel Pressure .......................................................718
Idle Speed and Ignition Timing .............................718
Calculated Load Value ..........................................718
Mass Air Flow Sensor ...........................................718
Intake Air Temperature Sensor .............................718
Engine Coolant Temperature Sensor ...................718
Air Fuel Ratio (A/F) Sensor 1 Heater ....................718
Heated Oxygen sensor 2 Heater ..........................718
Crankshaft Position Sensor (POS) .......................718
Camshaft Position Sensor (PHASE) ....................718
Throttle Control Motor ...........................................719
Fuel Injector ..........................................................719
Fuel Pump ............................................................719

ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-61
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
HOW TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION
How to Erase DTC
WITH CONSULT-III
The emission related diagnostic information in the ECM can be erased by selecting “ERASE” in the “SELF-
DIAG RESULTS” mode with CONSULT-III.
If DTCs are displayed for both ECM and TCM (Transmission control module), they need to be erased individu-
ally from the ECM and TCM (Transmission control module).
NOTE:
If the DTC is not for A/T related items (see EC-8, "
INDEX FOR DTC" ), skip steps 2 through 4.
1. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
2. Turn CONSULT-III ON and touch “A/T”.
3. Touch “SELF-DIAG RESULTS”.
HO2SAir fuel ratio (A/F) sensor 1 (Bank 1)P0131 41H 8EH Min. 5mV
P0132 42H 0EH Max. 5mV
P2A00 43H 0EH Max. 0.002
P2A00 44H 8EH Min. 0.002
P0133 45H 8EH Min. 0.004
P0130 46H 0EH Max. 5mV
P0130 47H 8EH Min. 5mV
P0133 48H 8EH Min. 0.004
Air fuel ratio (A/F) sensor 1 (Bank 2)P0151 4CH 8FH Min. 5mV
P0152 4DH 0FH Max 5mV
P2A03 4EH 0FH Max. 0.002
P2A03 4FH 8FH Min. 0.002
P0153 50H 8FH Min. 0.004
P0150 51H 0FH Max. 5mV
P0150 52H 8FH Min. 5mV
P0153 53H 8FH Min. 0.004
Heated oxygen sensor 2 (Bank 1)P0138 1CH 06H Max. 10mV
P0139 19H 86H Min. 10mV/500 ms
P0137 1AH 86H Min. 10 mV
P0138 1BH 06H Max. 10 mV
Heated oxygen sensor 2 (Bank 2)P0158 24H 07H Max 10mV
P0159 21H 87H Min. 10 mV/500 ms
P0157 22H 87H Min. 10 mV
P0158 23H 07H Max. 10 mV
HO2S HTRAir fuel ratio (A/F) sensor 1 heater (Bank 1) P0032 57H 10H Max. 5 mV
P0031 58H 90H Max. 5 mV
Air fuel ratio (A/F) sensor 1 heater (Bank 2)P0052 59H 11H Max. 5 mV
P0051 5AH 91H Max. 5 mV
Heated oxygen sensor 2 heater (Bank 1)P0038 2DH 0AH Max. 20 mV
P0037 2EH 8AH Min. 20 mV
Heated oxygen sensor 2 heater (Bank 2)P0058 2FH 0BH Max. 20 mV
P0057 30H 8BH Min. 20 mV Item Self-diagnostic test item DTCTest value (GST display)
Test limit Conversion
TID CID

EC-88
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
2
P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater

P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater

P0075 P0081 Intake valve timing control solenoid valve

P0078 P0084 Exhaust valve timing control magnet retarder*

P0130 P0131 P0132 P0133 P0150 P0151 P0152 P0153 P2A00 P2A03 Air fuel ratio (A/F) sensor 1

P0137 P0138 P0139 P0158 P0159 Heated oxygen sensor 2

P0441 EVAP control system purge flow monitoring

P0443 P0444 P0445 EVAP canister purge volume control solenoid valve

P0447 P0448 EVAP canister vent control valve

P0451 P0452 P0453 EVAP control system pressure sensor

P0550 Power steering pressure sensor

P0603 ECM power supply

P0710 P0717 P0720 P0731 P0732 P0733 P0734 P0735 P0740 P0744 P0745 P1730 P1752 P1757 P1762 P1767
P1772 P1774 A/T related sensors, solenoid valves and switches

P1078 P1084 Exhaust valve timing control position sensor

P1217 Engine over temperature (OVERHEAT)

P1233 P2101 Electric throttle control function

P1236 P2118 Throttle control motor

P1290 P2103 P2103 Throttle control motor relay

P1805 Brake switch
3

P0011 P0021 Intake valve timing control

P0014 P0024 Exhaust valve timing control*

P0171 P0172 P0174 P0175 Fuel injection system function

P0300 - P0306 Misfire

P0420 P0430 Three way catalyst function

P0442 EVAP control system (SMALL LEAK)

P0455 EVAP control system (GROSS LEAK)

P0456 EVAP control system (VERY SMALL LEAK)

P0506 P0507 Idle speed control system

P1148 P1168 Closed loop control

P1211 TCS control unit

P1212 TCS communication line

P1238 P2119 Electric throttle control actuator

P1421 Cold start control

P1564 ASCD steering switch

P1572 ASCD brake switch

P1574 ASCD vehicle speed sensor

P1715 Turbine revolution sensor Priority Detected items (DTC)

TROUBLE DIAGNOSIS
EC-103
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
ECM Harness Connector Terminal LayoutNBS0003L
ECM Terminals and Reference ValueNBS0003M
PREPARATION
ECM (1) is located behind the passenger side instrument lower
panel. For this inspection, remove passenger side instrument lower
panel.
ECM INSPECTION TABLE
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-III.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECMs transistor. Use a ground other than ECM terminals, such as the ground.
PBIB3537E
2 : ECM harness connector
PBIB3499E
TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
1W/RA/F sensor 1 heater
(bank 1)[Engine is running]

Warm-up condition

Idle speed
(More than 140 seconds after starting
engine)2.9 - 8.8V
PBIB3538E

EC-104
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
2GThrottle control motor
(Open) (bank 1)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressed0 - 14V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully released0 - 14V
3R/WThrottle control motor relay
power supply (bank 1)[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
4BRThrottle control motor
(Close) (bank 1)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: In the middle of releasing
operation0 - 14V
5GY/LA/F sensor 1 heater
(bank 2)[Engine is running]

Warm-up condition

Idle speed
(More than 140 seconds after starting
engine)2.9 - 8.8
6 L/ORExhaust valve timing control
magnet retarder (bank 1)[Engine is running]

Warm-up condition

Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

Around 2,500 rpm while the engine speed is
rising7 - 12V TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3539E
PBIB3540E
PBIB3541E
PBIB3538E
PBIB3542E

TROUBLE DIAGNOSIS
EC-105
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
7Y/RExhaust valve timing control
magnet retarder (bank 2)[Engine is running]

Warm-up condition

Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

Around 2,500 rpm while the engine speed is
rising7 - 12V
8 B/P ECM ground[Engine is running]

Idle speedBody ground
11
12
15
16
19
20GY
LG/R
PU
G/B
L/R
Y/BIgnition signal No. 4
Ignition signal No. 3
Ignition signal No. 5
Ignition signal No. 2
Ignition signal No. 6
Ignition signal No. 1[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm at
idle.0 - 0.2V
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpm0.1 - 0.4V
17 PHeated oxygen sensor 2
heater (bank 1)[Engine is running]

Engine speed: Below 3,600 rpm after the
following conditions are met.
–Engine: After warming up
–Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load.0 - 14V
[Ignition switch: ON]

Engine stopped
[Engine is running]

Engine speed: Above 3,600 rpmBATTERY VOLTAGE
(11 - 14V)
18 W/GIntake valve timing control
solenoid valve (bank 1)[Engine is running]

Warm-up condition

Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpm7 - 12V TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3542E
PBIB3543E
PBIB3544E
PBIB3545E
PBIB3546E

TROUBLE DIAGNOSIS
EC-107
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
30 YThrottle position sensor 1
(bank 1)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully releasedMore than 0.36V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressedLess than 4.75V
31 L/GThrottle position sensor 1
(bank 2)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully releasedMore than 0.36V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressedLess than 4.75V
33 PU/WHeated oxygen sensor 2
heater (bank 2)[Engine is running]

Engine speed: Below 3,600 rpm after the
following conditions are met.
–Engine: After warming up
–Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load.0 - 14V
[Ignition switch: ON]

Engine stopped
[Engine is running]

Engine speed: Above 3,600 rpmBATTERY VOLTAGE
(11 - 14V)
34 LThrottle position sensor 2
(bank 1)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully releasedLess than 4.75V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressedMore than 0.36V
35 L/YThrottle position sensor 2
(bank 2)[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully releasedLess than 4.75V
[Ignition switch: ON]

Engine stopped

Shift lever: D (A/T) or 1st (M/T)

Accelerator pedal: Fully depressedMore than 0.36V TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3545E

EC-118
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
X: Applicable
*1: This item includes 1st trip DTCs.
*2: This mode includes 1st trip freeze frame data or freeze frame data. The items appear on CONSULT-III screen in freeze frame data
mode only if a 1st trip DTC or DTC is detected. For details, refer to EC-119, "
Freeze Frame Data and 1st Trip Freeze Frame Data" .
*3: Always “CMPLT” is displayed.
INSPECTION PROCEDURE
Refer to GI-36, "CONSULT-III/GST CHECKING SYSTEM" .
WORK SUPPORT MODE
Work Item
ENGINE CONTROL COMPONENT PARTS
OUTPUT
Fuel injector××
Power transistor (Ignition timing)××
Throttle control motor relay××
Throttle control motor×
EVAP canister purge volume control
solenoid valve××××
Air conditioner relay×
Fuel pump relay×××
Cooling fan relay×××
Air fuel ratio (A/F) sensor 1 heater××
×*
3
Heated oxygen sensor 2 heater××
×*3
EVAP canister vent control valve×× ××
Intake valve timing control solenoid
valve×××
Exhaust valve timing control magnet
retarder×× ××
Calculated load value×× ItemDIAGNOSTIC TEST MODE
WORK
SUPPORTSELF-DIAGNOSTIC
RESULTS
DATA
MONI-
TORACTIVE
TESTDTC & SRT
CONFIRMATION
DTC*
1FREEZE
FRAME
DATA*
2
SRT STA-
TUSDTC
WORK
SUP-
PORT
WORK ITEM CONDITION USAGE
FUEL PRESSURE RELEASE

FUEL PUMP WILL STOP BY TOUCHING START DUR-
ING IDLING.
CRANK A FEW TIMES AFTER ENGINE STALLS.When releasing fuel pressure
from fuel line
IDLE AIR VOL LEARN

THE IDLE AIR VOLUME THAT KEEPS THE ENGINE
WITHIN THE SPECIFIED RANGE IS MEMORIZED IN
ECM.When learning the idle air volume
SELF-LEARNING CONT

THE COEFFICIENT OF SELF-LEARNING CONTROL
MIXTURE RATIO RETURNS TO THE ORIGINAL COEF-
FICIENT.When clearing the coefficient of
self-learning control value

TROUBLE DIAGNOSIS
EC-121
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
TP SEN 1-B1 [V]
The throttle position sensor signal voltage is dis-
played.
THRTL SEN 2-B1 signal is converted by ECM
internally. Thus, it differs from ECM terminal
voltage signal. TP SEN 2-B1 [V]
FUEL T/TMP SE [°C]
or [°F]

The fuel temperature (determined by the signal volt-
age of the fuel tank temperature sensor) is displayed.
INT/A TEMP SE [°C] or
[°F]

The intake air temperature (determined by the signal
voltage of the intake air temperature sensor) is indi-
cated.
EVAP SYS PRES [V]

The signal voltage of EVAP control system pressure
sensor is displayed.
FUEL LEVEL SE [V]

The signal voltage of the fuel level sensor is displayed.
START SIGNAL [ON/
OFF]

Indicates start signal status [ON/OFF] computed by
the ECM according to the signals of engine speed and
battery voltage.
After starting the engine, [OFF] is displayed
regardless of the starter signal.
CLSD THL POS [ON/
OFF]

Indicates idle position [ON/OFF] computed by ECM
according to the accelerator pedal position sensor sig-
nal.
AIR COND SIG [ON/
OFF]

Indicates [ON/OFF] condition of the air conditioner
switch as determined by the air conditioner signal.
P/N POSI SW
[ON/OFF]

Indicates [ON/OFF] condition from the park/neutral
position (PNP) switch signal.
PW/ST SIGNAL [ON/
OFF]

[ON/OFF] condition of the power steering system
(determined by the signal voltage of the power steer-
ing pressure sensor) is indicated.
LOAD SIGNAL [ON/
OFF]

Indicates [ON/OFF] condition from the electrical load
signal.
ON: Rear window defogger switch is ON and/or light-
ing switch is in 2nd position.
OFF: Both rear window defogger switch and lighting
switch are OFF.
IGNITION SW
[ON/OFF]

Indicates [ON/OFF] condition from ignition switch sig-
nal.
HEATER FAN SW
[ON/OFF]

Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW
[ON/OFF]

Indicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1 [msec]

Indicates the actual fuel injection pulse width compen-
sated by ECM according to the input signals.
When the engine is stopped, a certain com-
puted value is indicated.
INJ PULSE-B2 [msec]
IGN TIMING [BTDC]

Indicates the ignition timing computed by ECM
according to the input signals.
When the engine is stopped, a certain value is
indicated.
CAL/LD VALUE [%]

“Calculated load value” indicates the value of the cur-
rent air flow divided by peak air flow.
MASS AIRFLOW [g·m/
s]

Indicates the mass air flow computed by ECM accord-
ing to the signal voltage of the mass air flow sensor.
PURG VOL C/V [%]

Indicates the EVAP canister purge volume control
solenoid valve control value computed by the ECM
according to the input signals.

The opening becomes larger as the value increases.
INT/V TIM(B1) [°CA]

Indicates [°CA] of intake camshaft advanced angle.
INT/V TIM(B2) [°CA]
EXH/V TIM B1 [°CA]

Indicates [°CA] of exhaust camshaft retarded angle.
EXH/V TIM B2 [°CA] Monitored item [Unit] Description Remarks