battery NISSAN 350Z 2007 Z33 Roof Workshop Manual

RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF
Revision: 2006 November2007 350Z
ROOF
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions .............................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
SOFT TOP .................................................................11
Component Parts and Harness Connector Location .... 11
System Description ................................................ 12
CONDITIONS FOR OPERATION ....................... 13
CONDITIONS FOR STOPPING OPERATION .... 13
OUTLINE OF OPERATION ................................. 13
OPERATION: FULL CLOSE → FULL OPEN ...... 13
OPERATION: FULL OPEN → FULL CLOSE ...... 16
Operation Chart ...................................................... 19
CLOSE → OPEN ................................................ 19
OPEN → CLOSE ................................................ 21
Indicator Lamp ....................................................... 23
Schematic .............................................................. 24Wiring Diagram — F/ROOF — ............................... 25
Terminal and Reference Value of Soft Top Control
Unit ......................................................................... 33
CLOSE → OPEN OPERATION ........................... 33
OPEN → CLOSE OPERATION ........................... 35
Work Flow ............................................................... 37
Trouble Diagnosis Chart by Symptom .................... 37
(CLOSE → OPEN) .............................................. 37
(OPEN → CLOSE) .............................................. 38
Check Soft Top Control Unit Power Supply (OP, CL) ... 40
Check Soft Top Switch (OPEN) .............................. 40
Check Soft Top Switch (CLOSE) ............................ 42
Check 5th Bow Unlock Actuator (Open Operate) ... 44
Check 5th Bow Half-Latch Switch (Open Operate) ... 44
Check 5th Bow Actuator (Open Operate) ............... 46
Check 5th Bow Full Close Detection Switch (Open
Operate) ................................................................. 46
Check 5th Bow Full Open Detection Switch (Open
Operate) ................................................................. 48
Check Storage Lid Unlock Actuator (Open Operate) ... 49
Check Storage Lid Full Close Detection Switch
(Open Operate) ...................................................... 50
Check Storage Lid Actuator (Open Operate) .......... 52
Check Storage Lid Full Open Detection Switch
(Open Operate) ...................................................... 53
Check Roof Actuator (Open Operate) .................... 55
Check Roll Bar Interference Prevention Switch
(Open Operate) ...................................................... 56
Check Body Interference Prevention Switch (Open
Operate) ................................................................. 57
Check Roof Full Open Detection Switch (Open
Operate) ................................................................. 58
Check Storage Lid Unlock Actuator (Close Operate) ... 59
Check Storage Lid Full Close Detection Switch
(Close Operate) ...................................................... 60
Check Storage Lid Actuator (Close Operate) ......... 62
Check Storage Lid Full Open Detection Switch
(Close Operate) ...................................................... 63
Check Body Interference Prevention Switch (Close
Operate) ................................................................. 65

PRECAUTIONS
RF-3
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS00063
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNIS00064
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions NIS00065

Disconnect both battery cables in advance.

Never tamper with or force air bag lid open, as this may adversely affect air bag performance.

Be careful not to scratch pad and other parts.

When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.

When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.

Keep removed parts protected with cloth.

If a clip is deformed or damaged, replace it.

If an unreusable part is removed, replace it with a new one.

Tighten bolts and nuts firmly to the specified torque.

After re-assembly has been completed, make sure each part functions correctly.

Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
Do not use any organic solvent, such as thinner or benzine.

SOFT TOP
RF-13
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
CONDITIONS FOR OPERATION
Operation is avairable when all of the conditions below are satisfied.

Ignition switch is ON.

The brake pedal is ON.

Vehicle speed is 4 km/h (2 MPH) or less.

Battery voltage is approximately 10 V or more.
CAUTION:
Run the engine when operating or inspecting the soft top to prevent battery dies.
CONDITIONS FOR STOPPING OPERATION
Operation of the soft top stops when the conditions below are satisfied while the soft top is operating.

Any of the above operation conditions is no longer satisfied.

The passenger side power seat is operated. (It does not move when seat cancel switch is ON.)
OUTLINE OF OPERATION
Refer to the illustrations for the positions of the soft top, and the conditions of switch and actuator operation.
OPERATION: FULL CLOSE → FULL OPEN
Refer to RF-19, "State Chart" .

CONDITION: FULL CLOSE

CONDITION: OP 1
When the soft top switch is pushed to OPEN, the indicator lamp illuminates, windows activate to the fully-
open position and the passenger seat tilts forward by approximately 6 degrees by power window down
request signal. When passenger seat tilts forward by approximately 6 degrees, seat back position signal is
turned ON.

CONDITION: OP 2
The 5th bow unlock actuator operates, releasing the 5th bow lock.
Item Condition
5th bow half-latch switch : OFF
5th bow full-latch switch : OFF
5th bow ending switch : OFF
5th bow full open detection switch : OFF
5th bow full close detection switch : OFF
Storage lid full open detection switch : OFF
Storage lid full close detection switch LH : OFF
Storage lid full close detection switch RH : OFF
Roof full open detection switch : OFF
Roof full close detection switch : OFF
Body interference prevention switch : OFF
Roll bar interference prevention switch : OFF
Item Condition
Soft top switch : OPEN (Until the operation ends)
Indicator lamp : ON
Power window down request signal : ON
Seat back position signal : OFF → ON
Item Condition
5th bow unlock actuator : ON

SOFT TOP
RF-23
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Indicator LampNIS0006E
The indicator lights, turns off or blinks according to the operating state.
*: The soft top operates for approximately 30 seconds after turn ignition switch OFF.
Turns OFF : The open / close operation stops or completes or any switch is malfunctioning
Lights : The soft top is operating or the operation stops on the way
Blinks : The soft top cannot be operated, do not response or front lock is unlocked at
the fully closed position
State of roofThe operation stops when the soft top is,
Operation
full open or
full closein position on
the way
Operational condition Turning off Lighting Lighting
Out of operational
conditionWhen battery voltage decreases remarkably Turning off Lighting Lighting
Brake pedal is not depressed Turning off Lighting Lighting
Vehicle speed is 5 km/h (3 MPH) or more Turning off Lighting Lighting
Ignition switch: OFF Turning off Turning off* Turning off*
Malfunction ofany switch of the system Turning off Lighting Blinking
soft top control unit Blinking Blinking Blinking
vehicle speed signal Blinking Blinking Blinking

SOFT TOP
RF-33
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Terminal and Reference Value of Soft Top Control UnitNIS0006H
CLOSE → OPEN OPERATION
The operation chart for roof position. Refer to RF-19, "State Chart" .
Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: OP)Value (V)
(Approx.)
Signal nameInput/
Output
1 W/R Battery power supply Input — Battery voltage
3RRoof actuator RH
(OPEN) signalOutputOP8 → OP11 0 → Battery voltage → 0
Other than above 0
4G/R5th bow closure motor
(CLOSE) signalOutput — 0
5R/BStorage lid actuator RH
(OPEN) signalOutputOP6 → OP7
0 → Battery voltage → 0
OP12
Other than above 0
6 R 5th bow unlock actuator signal OutputOP2 → OP3 0 → Battery voltage → 0
Other than above 0
7 B Ground — — 0
8 W/R Battery power supply Input — Battery voltage
10 YRoof actuator RH
(CLOSE) signalOutput — 0
12 G/Y5th bow closure motor
(OPEN) signalOutputOP4 0 → Battery voltage → 0
Other than above 0
13 L/RStorage lid actuator RH
(CLOSE) signalOutputOP11 → OP12 0 → Battery voltage → 0
Other than above 0
14 W Speed signal (8 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40km/h (25 MPH)]
15 ORStorage lid unlock actuator LH and
RH signalOutputOP5 → OP6 0 → Battery voltage → 0
Other than above 0
16 B Ground — — 0
17 RIgnition switch
(ON or START)InputIgnition switch
(ON or START position)Battery voltage
18 SBSoft top switch
(OPEN) signalInputSoft top switch
open operate0
Other than above 5
19 R/WSoft top switch
(CLOSE) signalInputSoft top switch
close operate0
Other than above 5
20 W/BRoof full close detection switch
signalInput OP8 5 → 0
21 W/LRoof full open detection switch
signalInput OP11 5 → 0
22 W/RRoll bar interference prevention
switch signalInput OP9 5 → 0
PKIA1935E

RF-34
SOFT TOP
Revision: 2006 November2007 350Z
23 W/G Speed signal (2 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40 km/h (25 MPH)]
24 GStorage lid full close
detection switch (RH) signalInput OP5 → OP12 5 → 0 → 5
25 L/YStorage lid full close
detection switch (LH) signalInput OP6 → OP11 5 → 0 → 5
26 LG5th bow full open detection
switch signalInputOP5 → OP7 5 → 0 → 5
OP10 5 → 0
27 GY5th bow full close detection
switch signalInputOP4 → OP8 5 → 0 → 5
OP9 5 → 0
28 LG/BSoft top front lock detection
switch signalInput Front lock: Lock 5
: Unlock 0
29 R/Y 5th bow ending switch signal Input OP4 5 → 0
30 Y/R 5th bow full-latch switch signal Input OP4 5 → 0
31 L 5th bow half-latch switch signal Input OP3 5 → 0
32 WBody interference
prevention switch signalInput OP10 5 → 0
33 BRStorage lid full open
detection switch signalInput OP7 → OP11 5 → 0 → 5
34 L/W Seat back position signal InputWhen passenger seat
inclines forward0
Other than above 5
35 Y Indicator lamp signal InputOP1 → OP12 0
Other than above Battery voltage
36 PU Power window down signal OutputOP1→OP11 0
Other than above 5
37 RRoof actuator LH
(OPEN) signalOutputOP8 → OP11 0 → Battery voltage → 0
Other than above 0
38 W Brake pedal signal Input Brake pedal: Depressed Battery voltage
: Released 0
41 R/LStorage lid actuator LH
(OPEN) signalOutputOP6 → OP7
0 → Battery voltage → 0
OP12
Other than above 0
42 YRoof actuator LH
(CLOSE) signalOutput — 0
44 G/R5th bow actuator
(DOWN) signalOutputOP7 → OP8 0 → Battery voltage → 0
Other than above 0
45 G/Y5th bow actuator
(UP) signalOutputOP3 → OP5
0 → Battery voltage → 0
OP9 → OP10
Other than above 0 Termi-
nal No.Wire
colorDescription
Condition
(Roof position: OP)Value (V)
(Approx.)
Signal nameInput/
Output
PIIB0078J

SOFT TOP
RF-35
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
OPEN → CLOSE OPERATION
The operation chart for roof position. Refer to RF-21, "State Chart" .
48 Y/BStorage lid actuator LH
(CLOSE) signalOutputOP11 → OP12 0 → Battery voltage → 0
Other than above 0 Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: OP)Value (V)
(Approx.)
Signal nameInput/
Output
Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
1 W/R Battery power supply Input — Battery voltage
3RRoof actuator RH
(OPEN) signalOutput — 0
4 G/R5th bow closure motor
(CLOSE) signalOutputCL10 0 → Battery voltage → 0
Other than above 0
5R/BStorage lid actuator RH
(OPEN) signalOutputCL2 → CL3
0 → Battery voltage → 0
CL8
Other than above 0
6 R 5th bow unlock actuator signal Output — 0
7 B Ground — — 0
8 W/R Battery power supply Input — Battery voltage
10 YRoof actuator RH
(CLOSE) signalOutputCL3 → CL6 0 → Battery voltage → 0
Other than above 0
12 G/Y5th bow closure motor
(OPEN) signalOutput — 0
13 L/RStorage lid actuator RH
(CLOSE) signalOutputCL7 → CL8 0 → Battery voltage → 0
Other than above 0
14 W Speed signal (8 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40 km/h (25 MPH)]
15 ORStorage lid unlock actuator LH
and RH signalOutputCL1 → CL2 0 → Battery voltage → 0
Other than above 0
16 B Ground — — 0
17 RIgnition switch
(ON or START)InputIgnition switch
(ON or START position)Battery voltage
18 SBSoft top switch
(OPEN) signalInputSoft top switch
open operate0
Other than above 5
19 R/WSoft top switch
(CLOSE) signalInputSoft top switch
close operate0
Other than above 5
20 W/BRoof full close detection
switch signalInput CL6 0 → 5
21 W/LRoof full open detection switch
signalInput CL3 0 → 5
PKIA1935E

RF-36
SOFT TOP
Revision: 2006 November2007 350Z
22 W/RRoll bar interference prevention
switch signalInput CL5 0 → 5
23 W/G Speed signal (2 pulse)Input/
OutputSpeed meter operate
[When vehicle speed is
Approx. 40 km/h (25 MPH)]
24 GStorage lid full close
detection switch (RH) signalInput CL1 → CL8 5 → 0 → 5
25 L/YStorage lid full close
detection switch (LH) signalInput CL2 → CL7 5 → 0 → 5
26 LG5th bow full open detection
switch signalInputCL4 0 → 5
CL7 5 → 0
CL8 0 → 5
27 GY5th bow full close
detection switch signalInputCL5 → CL6 0 → 5 → 0
CL9 0 → 5
28 LG/BSoft top front lock detection
switch signalInput Front lock: Lock 5
: Unlock 0
29 R/Y 5th bow ending switch signal Input CL10 0 → 5
30 Y/R 5th bow full-latch switch signal Input CL10 0 → 5
31 L 5th bow half-latch switch signal Input CL9 → CL10 0 → 5
32 WBody interference
prevention switch signalInput CL3 0 → 5
33 BRStorage lid full open
detection switch signalInput CL3 → CL7 5 → 0 → 5
34 L/W Seat back position signal InputWhen passenger seat
inclines forward0
Other than above 5
35 Y Indicator lamp signal InputCL1 → CL10 0
Other than above Battery voltage
36 PU Power window down signal OutputCL1 → CL10 0
Other than above 5
37 RRoof actuator LH
(OPEN) signalOutput — 0
38 W Brake pedal signal Input Brake pedal: Depressed Battery voltage
: Released 0
41 R/LStorage lid actuator LH
(OPEN) signalOutputCL2 → CL3
0 → Battery voltage → 0
CL8
Other than above 0
42 YRoof actuator LH
(CLOSE) signalOutput CL3 → CL6 0 → Battery voltage → 0
44 G/R5th bow actuator
(DOWN) signalOutputCL4 → CL5
0 → Battery voltage → 0
CL8 → CL10
45 G/Y5th bow actuator
(UP) signalOutput CL6 → CL7 0 → Battery voltage → 0 Termi-
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
PIIB0078J

SOFT TOP
RF-37
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Work FlowNIS0006I
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to RF-12, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to RF-37,
"Trouble Diagnosis Chart by Symptom" .
4. Does soft top system operate normally? If Yes, GO TO 5. If No, GO TO 3.
5. INSPECTION END.
Trouble Diagnosis Chart by SymptomNIS0006J
(CLOSE → OPEN)
The operation chart for roof position. Refer to RF-19, "State Chart" .
48 Y/BStorage lid actuator LH
(CLOSE) signalOutputCL7 → CL8 0 → Battery voltage → 0
Other than above 0 Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
Symptom Diagnostic procedure and repair order Roof position Refer to page
Roof does not operate1. Check soft top control unit power supply OP1RF-40
2. Check soft top switch (Open) OP1RF-40
3. Check operation permission condition OP1RF-78
4. Check each switch condition (Open operate) Full closeRF-80
5. Check seat back position signal OP1RF-83
6. Check 5th bow unlock actuator (Open operate) OP2RF-44
7. Check 5th bow half-latch switch (Open operate) OP2RF-44
8. Check 5th bow actuator (Open operate) OP3RF-46
5th bow operation stops at full
open position1. Check 5th bow full close detection switch
(Open operate)OP4RF-46
2. Check 5th bow full open detection switch
(Open operate)OP5RF-48
3. Check storage lid unlock actuator
(Open operate)OP5RF-49
4. Check storage lid full close detection switch (LH
and RH) (Open operate)OP5.6RF-50
5. Check storage lid actuator (Open operate) OP6RF-52
Storage lid operation stops at
full open positionCheck storage lid full open detection switch (Open
operate)OP7RF-53
Roof does not operate Check roof actuator (Open operate) OP8RF-55
Roof stops on the wayCheck roll bar interference prevention switch
(Open operate)OP8RF-56
Storage lid operation stops at
full open position after the roof
is stored.1. Check body interference prevention switch
(Open operate)OP10RF-57
2. Check roof full open detection switch OP10RF-58
Passenger side seat back does
not operate.1. Check passenger side seat cancel switch OP1SE-52
2. Check passenger side seat operate signal 1 OP1RF-82
Passenger side seat bock does
not return to former stateCheck passenger side seat operate signal 2 OP10RF-83
Power window down does
not operate.Check power window harness OP1RF-82

RF-40
SOFT TOP
Revision: 2006 November2007 350Z
Check Soft Top Control Unit Power Supply (OP, CL)NIS0006K
1. CHECK FUSE

Check 10A fuse [No.12, located in the fuse block (J/B)]

Check 40A fusible link (letter G located in the fuse and fusible link box.)
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Start engine.
2. Check voltage between soft top control unit connector B66, 67
terminal 1, 8, 17 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check soft top control unit power supply circuit for open
or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit connector.
3. Check continuity between soft top control unit connector B66
terminal 7, 16 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check soft top control unit ground circuit for open or
short.
Check Soft Top Switch (OPEN)NIS0006L
1. CHECK SOFT TOP OPEN SWITCH SIGNAL
1. Start engine.
2. Check soft top control unit connector and ground.
OK or NG
OK >> Soft top switch (OPEN) is OK.
NG >> GO TO 2.1 (W/R) - Ground : Battery voltage
8 (W/R) - Ground : Battery voltage
17 (R) - Ground : Battery voltage
PIIA7886E
7 (B) - Ground : Continuity should exist.
16 (B) - Ground : Continuity should exist.
PIIA7887E
ConnectorTerminal (Wire color)
Soft top switch
ConditionVoltage (V)
(Approx.)
(+) (-)
B67 18 (SB) GroundOPEN 0
Other than above 5
PIIA7888E