brake sensor NISSAN GT-R 1998 User Guide

ANTI-LOCK BRAKE SYSTEM
ABS control unit connector
Terminal No.
Control Unit InputlOutput Signal Specifications
USING CIRCUIT TESTER
To perform the following inspection, the ignition switch should be
turned
ON with ABS control unit connector and actuator connector
properly connected.
Item Specifications*l
Battery Ignition switch ON: Battery voltage (Approx. 12V)
Brake pedal is depressed: Battery voltage (Approx. 12V)
Stop lamp signal
Brake pedal is not depressed: Less than approx.
2V
ABS motor is running
ABS motor relay (in
CONSULT active test mode): Less than approx.
2V
ABS motor is stopped: Battery voltage (Approx.
12V)
Actuator relay is activated (with engine running): Less than approx. 2V
Actuator relay Actuator
relay is not activated (with fail-safe function activated and engine
not running): Battery voltage (Approx. 12V)
Actuator relay is activated (with engine running): Battery voltage (Approx.
Actuator relay 1 2V)
monitor Actuator
relay is not activated (with fail-safe function activated and engine
not running): Approx. OV
Front
right inlet
Actuator is activated (in CONSULT active test mode), or actuator relay is
solenoid not activated (with fail-safe function activated and engine not running):
Rear inlet solenoid Approx. OV
Front
left inlet Actuator
is not activated and actuator relay is activated (with vehicle
solenoid stopped
and engine running): Battery voltage (Approx. 12V)
ABS motor is running (in CONSULT active test mode): Battery voltage
ABS motor monitor (Approx. 12V)
ABS motor is stopped (with ignition switch
ON): Approx. OV
ABS warning lamp
ON'2:
Approx. OV
ABS warning lamp
ABS warning lamp
OFF'2:
Battery voltage (Approx. 12V)
Front right wheel
sensor Wheels are turning (Approx. 30
krn/h)*3: Pulse generates.
Front: Approx. 200
Hz
sensor
Rear: Approx. 400 Hz
Front right outlet
Actuator is activated (in CONSULT active test mode), or actuator relay is
not activated (with fail-safe function activated and engine not running):
Rear outlet
sole-
Approx. OV
I lUlU / Actuator is not activated and actuator relay is activated (with vehicle Front left Outlet stopped and engine running): Battery voltage (Approx. 12V)
solenoid
'1:e
to
tooen
a connector terminal when
using a circuit tester for inspection. Control
I
unit
power
supply circuit
ST
Stop lamp switch
and circuit
ABS motor, motor
R8
relay and circuit
ABS actuator relay
and circuit
pL
ABS warning lamp
and circuit, ABS
actuator relay
SD monitor circuit
ABS solenoid and
circuit
ABS motor monitor
circuit
ABS warning lamp
and circuit
Wheel sensors and circuit
ABS solenoid and
circuit
'2: ABS warning lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected ABS warning lamp OFF: One second after the ignition switch is turned ON (with the system in normal condition) *3: Tire pressure must be in accordance with specification.

ANTI-LOCK BRAKE SYSTEM
Control Unit InputfOutput Signal Specifications
(Cont'd)
USING CONSULT
Indicated are the control unit computed data. If the output circuit (harness) should be open or short-
circuited, correct values may be displayed.
Check item (Reference)
Data monitor
Display Condition
Monitor
item
Specifications
Vehicle is stationary.
I 0 kdh
FR RH SENSOR
FR LH SENSOR
RR SENSOR
[kdh]
Virtually the same speed
as speedometer (within
+I 0%)
Wheel sensor and circuit
Wheel speed
Vehicle is
drivem'l
Brake pedal is
depressed. Stop lamp switch and
circuit
STOP
LAMP SW
[ON-OFF] Brake pedal status
Brake pedal is not
depressed. OFF
-- --
Actuator (solenoid)
is
activated (at CONSULT
active test),
or
actuator relay is not
activated (with fail-safe
function activated and
engine not running).
FR
RH IN SOL
FR
LH IN SOL
REAR IN SOL
[ON-OFF]
ABS solenoid and circuit
Solenoid status
FR RH OUT SOL
FR
LH OUT SOL
REAR OUT SOL
[ON-OFF]
-- -- - -- -
Actuator (solenoid) is not
activated and actuator
relay is activated (with
vehicle stopped and
engine running).
Actuator relay is acti-
vated (with engine run-
ning).
Actuator relay is not acti-
vated (with fail-safe
function activated and
engine not running).
ABS actuator relay and
circuit
OFF
ON
OFF
ACTUATOR
RLY
[ON-OFF] Actuator
relay status
Motor relay and motor
are activated (at CON-
SULT active test). ABS
motor, motor relay,
and circuit
MOTOR
RLY
[ON-OFF] Motor
relay and motor
status Motor relay and motor
are not activated. OFF
ABS warning lamp and
circuit
- -
Waming lamp ON'2 1 ON
WARNING LAMP
[ON-OFF] ABS
warning lamp sta-
tus
Power supply voltage
provided for control unit -- -
Warning lamp OFF'2 1 OFF
Control unit power sup-
ply circuit - -
BAlTERY VOLT [V] Ignition switch
ON
'1: Tire pressure must be in accordance with specification. "2: ABS warning lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected ABS warning lamp OFF: One second after the ignition switch is turned ON (with the system in normal condition)

ANTI-LOCK BRAKE SYSTEM
CONSULT
(Cont'd)
SELF-DIAGNOSTIC RESULTS MODE
Diagnostic item I Diagnostic item is detected when ... I Check item
FR RH SENSOR
[OPEN] Circuit
for front right wheel sensor is open. Or an abnormally high input voltage is
entered due to short to battery.
FR LH SENSOR
[OPEN]
- -- -- - - - ---
Circuit for front left wheel sensor is open. Or an abnormally high input voltage is entered
due to short to battery.
1
FR RH SENSOR
[SHORTJ'I
, '2
REAR SENSOR
[OPEN] Circuit
for rear wheel sensor is open. Or an abnormally high input voltage is entered due
to short to battery.
1
FR LH SENSOR
[SHORT] Front
right wheel sensor is short-circuited or shorted to ground, or gap between the
wheel sensor and the sensor rotor is large. An abnormally low
input voltage is entered
and input signal is abnormal.
Front left wheel sensor is short-circuited or shorted to ground, or gap between the wheel
sensor and the sensor rotor is large. An abnormally low input voltage is entered and
input signal is abnormal. Wheel
sen-
sor and cir-
cuit
REAR SENSOR
[SHORT
11'1, '2
Rear wheel sensor is short-circuited or shorted to ground, or gap between the wheel
sensor and the sensor rotor is large.
An abnormally low input voltage is entered and
input signal is abnormal.
FR RH IN ABS SOL
[OPEN]
FR LH IN ABS SOL
[OPEN] Circuit
for front right inlet solenoid valve is open, or an output voltage is much lower than
the specified value due to short to ground.
Circuit for front left inlet solenoid valve is open, or an output voltage is much lower than
the specified value due to short to ground.
REAR IN ABS SOL
[OPEN] Circuit
for rear inlet solenoid valve is open, or
an output voltage is much lower than the
specified value due to short to ground.
FR RH IN ABS SOL
[SHORT] Circuit
for front right inlet solenoid valve is shorted, or an output voltage is much higher
than the specified value due to short to battery.
FR LH IN ABS SOL
[SHORT] Circuit for front
left inlet solenoid valve is shorted, or an output voltage is much higher
than the specified value due to short to battery.
REAR IN ABS SOL
[SHORTJ
FR RH OUT ABS SOL
[OPEN]
FR
LH OUT ABS SOL
[OPEN]
REAR OUT ABS SOL
[SHORT]
FR RH OUT ABS SOL
[SHORT]
FR LH OUT ABS SOL
[SHORT]
RWR OUT ABS SOL
[SHORT] Circuit for
rear inlet solenoid valve is shorted, or an output voltage is much higher than
the specified value due to short to battery.
Circuit for front right outlet solenoid valve
is open, or an output voltage is much lower
than the specified value due to short to ground.
Circuit for front left outlet solenoid valve is open, or an output voltage is much lower than
the specified value due to short to ground.
Circuit for rear outlet solenoid valve is open, or an output voltage is much lower than the
specified value due to short to ground.
Circuit for front right outlet solenoid valve
is shorted, or an output voltage is much higher
than the specified value due to short to battery.
Circuit for front left outlet solenoid valve is shorted, or an output voltage is much higher
than the specified value due to short to battery.
- -- -- - - Circuit for rear outlet solenoid valve is shorted, or an output voltage is much higher than
the specified value due to short to battery.
ABS MOTOR
[ON FAILURE]
ABS MOTOR
[OFF FAILURE] ABS
sole-
noid
and cir-
cuit
ABS ACTUATOR RELAY
[ON FAILURE]
ABS ACTUATOR RELAY
[OFF FAILURE] ABS
motor turns ON when control unit sends OFF signal. ABS motor circuit is open or
shorted to ground.
ABS motor turns OFF when control unit sends ON signal. Relay control wire is broken. ABS motor,
motor relay
and circuit
ABS actuator relay tums ON when control unit sends OFF signal. Actuator relay is
short-
circuited to ground.
ABS actuator relay tums OFF when control unit sends ON signal. Relay control wire is
broken. ABS
actuator
relay and
circuit

ANTI-LOCK BRAKE SYSTEM
CONSULT (Cont'd) - -
Diagnostic item
CONTROL UNIT --
BAnERY "OLTAGE
[VB-HIGH]
"OLTAGE
[VB- LO
W]
Function of calculation in ABS control unit has failed.
Diagnostic
item is detected when
...
Control unit,
control
unit
power supply
and ground
circuit
Check item
ABS control unit battery voltage
is abnormally high.
ABS control unit battery voltage is abnormally low.
. ABS MOTOR
[LOCK FAILURE] Control
unit
power supply
circuit ABS motor speed is abnormally low. AES motor,
motor relay
and circuit
1 I
'1 : ABS warning lamp turns on if a wheel or wheels spin for I0 to 80 seconds (depending on the wheel speed) with the vehicle
stuck in snow. ice, or mud. This is a normal condition.
'2: After repairing short-circuited sensor, turning ignition switch ON lights up ABS warning lamp. Check that ABS warning lamp
turns
off when the vehicle is driven at approx. 30 krnh for approx. 1 minute as shown in the self-diagnosis procedure. NOTE: If "ABSn is not displayed on "SELECT SYSTEM" screen, check ABS control unit and data link connector circuit, and make sure
of the CONSULT card number.
DATA MONITOR PROCEDURE
Refer to CONSULT Instruction Manual for details on data
monitor function.
1. Turn ignition switch OFF.
2. Connect CONSULT connector to data link connector for CON-
SULT.
3. Turn ignition switch ON.
4. Touch "START' on CONSULT screen.
5. Touch "ABS" on CONSULT screen.
If "START" is touched immediately after engine is started
or ignition switch is turned on,
"ABS" may not be dis-
played on "SELECT SYSTEM" screen. To display "ABS",
repeat the data monitor procedure from the beginning.
6. Touch "DATA MONITORn.
7. Touch "SETTING" to set recording condition.
8. Touch "AUTO TRIG", "LONG TIME" and then "ENTER".
9. Return to "SELECT MONITOR ITEM" screen and touch "CIU
INPUT ITEM", "ALL SIGNALS" or 'SELECTION FROM
MENU". Refer to "DATA MONITOR MODE" on the next page.
10. Touch "START'.
11. Display data monitor.
12. If necessary, sequentially touch "REC START, "REC STOP",
"DATA DISPLAY", "NUMBER PRINT' and "PRINT' to print out
the data.

ANTI-LOCK BRAKE SYSTEM
CONSULT (Cont'd)
DATA MONITOR MODE
MONITOR ITEM I CONDITION
FR RH SENSOR
FR
LH SENSOR
RR SENSOR Drive vehicle.
(Each wheel is rotating.)
STOP LAMP SW Turn
ignition switch ON and
depress brake pedal.
FR RH
IN SOL
FR RH OUT SOL
FR
LH IN SOL
FR LH OUT SOL
REAR IN SOL
REAR OUT SOL Ignition
switch is turned ON or
engine is running.
ACTUATOR RLY
MOTOR RLY
Ignition switch is turned ON or
engine is running.
WARNING LAMP
BATTERY VOLT
I
VOLTAGE Indicates
the voltage mea-
sured with a voltage probe.
PLS WIDTH-H
I
Refer to CONSULT Instruction
Manual.
NlSSAN
CONSULT
START I --
1 SUB MODE BR455C
$ SELECT SYSTEM 0-
ENGINE
A/T
I - ABS I
SPECIFICATION
Displays computed vehicle speed from wheel sensor signal.
Almost the same speed as speedometer.
Depress the pedal: ON
Release the pedal: OFF
EC ;
Operating conditions for each solenoid valve are indicated. ABS is AT '
not operating: OFF
Displays ON/OFF condition of ABS actuator relay.
When turning ignition switch ON,
ABS actuator relay
is operated. 2
ABS is not operating: OFF
ABS
is operating: ON
Warning lamp is turned on: ON
R8 $
Warning lamp is turned off: OFF
Power supply voltage for control unit
~~~~
ACTIVE TEST PROCEDURE
When conducting Active test, vehicle must be stationary.
Confirm that brakes have been bled completely.
When ABS warning lamp stays on, never conduct Active test.
Turn ignition switch OFF.
Connect CONSULT to Data Link Connector for CONSULT.
Start engine.
Touch "START' on CONSULT screen.
Touch
"ABS".

ANTI-LOCK BRAKE SYSTEM
Self-diagnosis (Cont'd)
Example: Code No. 25 Front left wheel sensor (open-ccrcuit)
lnd~cat~on
s:arl
Start code No. i2
Unit: seconds BRG1185D
ABS warnq lamp ON -
A9S warnrng lamp OFF
Self-d~agnosis complete , C ABS warning lamp !
I i I I I
................ &. j(j(?.:e~o"dd~i!~?!!f!!. . -----... .-.---.--. iiii rase 1 12.5 seconds I mode
Malfunct~on
memory Malfunction memory is Nn. erase mode starts. Is erased BRG0057C
Tens d~g~ts Un~ts digits Code No 25 I I - I
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
r--------- -T---t----t-l-T-l-
1. Turn the ignition switch "ON" and start the engine.
-.
---------- -I--I--t--l-i-"I
2. Drive the vehicle at approx. 30 kmh for approx. 1 minute to
check that there is no other malfunction.
ST
3. Stop the vehicle.
4. Turn the ignition switch "OFF'.
5. Ground the self-diagnostic check terminal. RS'
6. Turn the ignition switch "ON" to start the self-diagnostic results
-
-.
3 06 0.9 03C303 3.3 06 0.6 0.6 09 050303030305030303
-----
mode.
CAUTION:
c--
Do not depress the brake pedal during self-diagnosis. Do not
start the engine. (The self-diagnosis
would not start.)
7. The ABS warning lamp starts to blink 3 or 4 seconds after the EL
self-diagnostic results mode is started.
8. Under the self-diagnostic results mode, the malfunction $jD
memory erase mode starts when the check terminal is discon-
nected from the ground.
9. Ground the check terminal 3 times or more in succession
within 12.5 seconds after the erase mode starts. (Each ground-
ing must
be 1 second or longer.)
10. Disconnect the grounding cable from the check terminal to
erase the malfunction memory and complete the
self-diagno-
sis. The ABS warning lamp
, then, turns off.
11. Turn the ignition switch
"OFF'.

ANTI-LOCK BRAKE SYSTEM
Self-diagnosis (Cont'd)
MALFUNCTION CODEISYMPTOM CHART
Malfunction code No. Malfunctioning
part ABS warning
lamp
ON
Fail-safe
operation
18 1 Different number of teeth of sensor rotors 1010
2 1
26 I Front left wheel sensor (short-circuiQ.4 1010
- --
22
25
3 1 I Rear wheel sensor (open-circuit) 1010
Front right wheel sensor (open-circuit)
32 Rear wheel sensor (short-circuit)'4 1 0 1 0
Front right wheel sensor (short-circuit)'4
Front left wheel sensor (open-circuit)
41
I Front right outlet ABS solenoid valve and circuit 1010
0 0
0
0
0
0
- -
42
-- - -
46 Front left inlet ABS solenoid valve and circuit 0 1 0
45 Front
left outlet ABS solenoid valve and circuit
55
1 Rear outlet ABS solenoid valve and circuit 1010
Front right inlet ABS solenoid valve and circuit
56
1 Rear inlet ABS solenoid valve and circuit 1010
0
57 1 Power supply (Low or high voltage)*2 I 0 I -'I
0
0
0
I At self-diagno- ( ABS control unit or data link connector for CONSULT is poorly 1 I
61
63
At self-diagno-
I ABS control unit
sis only
ABS
actuator motor or motor relayg3
ABS
actuator relay
No indication
I I ABS control unit1ABS actuator relay is stuck to OFFJABS I Stays ON power supply circuit, ABS actuator relay drive side power sup-
lgnition switch
ply (coil side) circuit, and ABS warning lamp circuit are
short-
circuited./ABS control unit connector is disconnected or poorly
0
0
I
sis only
Ignition switch
ON
I I connected. I I
0
0
connected.
ABS control
unit1Fuse is blown or ABS warning lamp has an
open circuit.
- -- '1: Fail-safe operation does not activate. A signal from ABS control unit suspends ABS control operation. Brakes operate con-
ventionally. After specified power supply voltage resumes, ABS warning lamp goes out, allowing for ABS control operation. '2: The code No. does not indicate a malfunction related to the ABS control unit. Do not replace the ABS control unit even if the code No. appears. '3: The code No. can sometimes appear when the ABS motor ground circuit is loose or disconnected. When it appears, always
check the ground circuit for improper installation.
'4: ABS warning lamp turns on if a wheel or wheels spin for 10 to 80 seconds (depending on the wheel speed) with the vehicle
stuck in snow, ice, or mud. This is a normal condition. After repairing short-circuited sensor, turning ignition switch ON lights
up
ABS warning lamp. Check that ABS warning lamp turns off when the vehicle is driven at approx. 30 krnlh for approx. 1 minute as shown in the self-diagnosis procedure.

TCSIABS SYSTEM
System
Description
ABS FUNCTION
During ABS operation, the brake pedal pulsates along with a mechanical noise. This ensures that the ABS
is working properly. mP
When starting up the engine or immediately after the vehicle starts to run, the brake pedal pulsates and G'
a motor noise from the engine compartment can be heard. They are caused by the ABS operation check
and should not be considered abnormal.
A vehicle with the ABS may stop in a longer distance than a vehicle without the ABS when the brake is
EC
applied on a bad road, gravel road, or deep fresh snow.
TCS FUNCTION
TCS/ABS control unit monitors the speed of the driving wheels through 4 wheel speed sensors. If driving
wheel slip is detected, fuel to the engine is cut
ol
and the throttle valve is adjusted so that the engine
a
torque is reduced. On vehicles with automatic transmission, transmission shift schedule is also changed
to control the rear wheel driving torque, which results
in the reduction of wheel slip. This system enables
the throttle valve to be controlled so that optimum engine torque can be achieved in accordance with the
driver's acceleration request.
The driver may not feel satisfied with acceleration on some road surfaces. This poor acceleration occurs
because the operating TCS gives priority to maintaining optimum traction. Therefore, this condition should
R8
be considered normal.
When shiftdown is made or the acceleration pedal is depressed while the vehicle is driven on the road
surface that has different friction coefficients, the TCS may operate temporarily.
r-- 4 Lrd[-i
On vehicles with manual transmission, the SLlP indicator lamp and the TCS OFF indicator lamp may light
up when the engine is about to stall in the conditions shown below.
If the lamps go off when engine speed
increases, there is no problem in the system.
At start, the engine almost stalls and the engine speed is much lower than the idle speed.
The vehicle is driven at an extremely low speed with a high-speed gear engaged.
The clutch has been engaged until the vehicle almost stops. 8D
FAIL-SAFE FUNCTION
ABS system
If any malfunction is detected in the system, the ABS warning lamp, the TCS OFF indicator lamp and the SLlP
indicator lamp in the instrument panel is turned on with the TCSIABS deactivated and the vehicle's brake sys-
tem reverts to normal operation.
TCS system
If any malfunction is detected in the system, both the SLlP indicator lamp and the TCS indicator lamp on the
instrument panel light up and the TCS is shut down. The vehicle operates in the same manner as a vehicle
without the
TCS, while the ABS is operational.
If there is a malfunction in the throttle control system, the TCS becomes inoperative while the ABS
remains functional.
When fail-safe operation is activated, perform the self-diagnosis procedure for the TCSIABS first.
Refer to
BR-27 for details.

TCSIABS SYSTEM
Control Unit
InputlOutput Signal Specifications
USING CIRCUIT TESTER
TCS/ABS control unit - -
To perform the following inspection, the ignition switch should be turned ON with TCS/ABS control unit con-
nector and actuator connector properly connected.
I
TCS/ABS contro! unit connector
Terminal No.
P Front right wheel I
Item
sensor
I
Specifications'l
Rear right wheel Wheels are turning (Approx.
30 km/h)'3: Pulse generates.
Front: Approx. 200
Hz
Rear: ADDrox. 200 Hz I . , sensor
Rear left wheel
sensor
I
I
Brake pedal is depressed: Battery voltage (Approx. 12V)
Stop lamp signal Brake pedal is not depressed: Less than approx. 2V
Actuator relay is activated (with engine running): Less than approx.
2V
Actuator relay Actuator relay
is not activated (with fail-safe function activated and engine
not running): Battery voltage (Approx.
12V)
ABS motor is running (in CONSULT active test mode): Battery voltage
ABS motor monitor (Approx. 12V)
ABS motor is stopped (with ignition switch ON): Approx. OV
SLIP
indicator
SLIP
indicator lamp
ON'S: OV
lamp
SLIP
indicator lamp
OFF'5: Battery voltage (Approx. 12V)
TCS OFF indicator TCS OFF indicator lamp
ON'4: OV
lamp TCS OFF indicator lamp
OFF'4: Battery voltage (Approx. 12V)
TCS OFF switch TCS OFF switch is pressed: Approx. OV
signal TCS OFF switch is not pressed: Approx. 4
- 5V
Engine speed sig-
nal Pulse generates.
Refer to EC section
("ECM.TCM Input/Outout Reference Value")
Total control signal
(Multiple communi-
cation) for engine,
A/T and TCSIABS Check item (Refer-
ence)
Wheel sensors
and circuit Stop lamp switch
and circuit
ABS actuator relay
and circuit
ABS motor monitor
circuit
SLlP indicator
lamp and circuit
TCS OFF indicator
lamp and circuit
TCS OFF switch
and circuit
Engine speed sig-
nal circuit
Circuit for total
control signal (Mul-
tiple communica-
tion) for engine, A/T and TCSIABS

TCSlABS SYSTEM
Control Unit InputfOutput Signal Specifications
(Cont'd)
USING CONSULT
Indicated are the controi unit computed data. If the output circuit (harness) should be open or short-
circuited, correct values may be displayed.
TCS/ABS control unit
Display
I Vehicle is stationary.
REVOLUTION SENSOR
W/hI
STOP LAMP SW [ON-OFF] Check
item (Reference)
Data monitor
the
same 'peed Wheel sensor circuit
as speedometer (within
~onttor
ltem
Wheel
speed'l
Vehicle is
driven.'l
Condition
Brake pedal is
Brake pedal is not
depressed.
Engine is stopped.
Engine is running at
more than
400 rpm.
Actuator (solenoid) is
activated (at CONSULT Specifications
Brake pedal status
-1 Engine speed signal cir-
cuit
ENG
RPM SIGNAL
[STOP-RUN] Engine operation
active test), or actuator
relay is not activated
(with fail-safe function
activated and engine not
running). Solenoid circuit
IN
ABS SOLENOID
[ON-OFF]
Solenoid status Actuator (solenoid) is
not
activated and actuator
relay
is activated (with
vehicle stopped and
engine running).
OUT
ABS SOLENOID
[ON-OFF] OFF
Actuator relay is acti-
vated (with engine run-
ning).
ABS ACTUATOR RELAY
[ON-OFF]
- Actuator relay and circuit
Actuator
relay status
Actuator relay is not acti-
vated (with fail-safe
function activated and
engine not running).
Motor relay and motor
are activated (at CON-
SULT active test).
Motor relay and motor
are not activated. OFF
I ABS
motor, motor relay
ABS MOTOR
RELAY
[ON-OFF]
Motor
relay
and motor
status
OFF and circuit
ABS warning lamp cir-
cuit
Controi unit power
sup-
WARNING LAMP
[ON-OFF]
4BS
warning lamp
sta-
:us'2
Warning lamp ON Warning lamp OFF
'ewer supply voltage
~rovided for control unit
BATERY
BOLT [V] Ignition switch ON
Acceleration pedal is not
depressed. (Ignition
switch
ON)
10 - 16V
I
Communication line cir-
cuit between TCS/ABS
control unit and throttle
I - 10096 control unit ply circuit and ground
circuit
rhrottle
angle condition
linked with acceleration
~edal)
THRTL OPENING
[%]
Acceleration pedal is
depressed. (Ignition
switch ON)