brake sensor NISSAN GT-R 1998 Owner's Manual

TCS/ABS SYSTEM
Self-diagnosis for TCS/ABS Control Unit
control System (Cont'd)
Example: Code No. 25 Front left wheel sensor (open-circutt)
lnd~cat~on
start Start code No.
12
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
1. Turn the ianition switch "ON" and start the engine.
ABS warnlng lamp - ON
ABS warning lamp
OFF
2. Drive the iehicle at approx. 30 km/h for appfox. 1 minute to
check that there
is no other malfunction.
3. Stop the vehicle and turn the ignition switch "OFF'. I88
4. Ground the self-diagnostic check terminal 4 on the data link
connector for CONSULT.
5. Turn the ignition switch "ONn to start the self-diagnostic results /,%@A
mode.
I---------- -------------- -?-I 3 06 0.9 03C303 3 3 06 3.6 06 09 030303030303030303
Unit: seconds BRG1185D
Tens drglts Units drgits Code No. 25
I -----l
7. Under the self-diagnostic results mode, the malfunction
memory erase mode starts when the check terminal
is discon-
nected from the ground.
8. Ground the check terminal 3 times or more in succession
-.
self-d~agnosts complete
SLlP ndicator lamp i
I ON r
f OFF - c 4 i
ground J Erase -- - - - - - - - - -i - - - - ---f2.i geconds-- - - - - - - .. t mode
Malfunct~on
memory
Malfunct~on
memory
IS erase mode starts. 1s erased. BRZOO~~D
within 12.5 seconds after the erase mode starts. (Each ground-
ing must be
2 seconds or longer.)
9. Disconnect the grounding cable from the check terminal to
erase the malfunction memory and complete the
self-diagno-
-----
CAUTION:
Keep terminal 4 grounded during self-diagnosis. Do not EL
depress the brake pedal during self-diagnosis. Do not start the
engine.
6. The SLIP indicator lamp starts blinking to indicate the malfunc- SD
tion code No. 3 or 4 seconds after the self-diagnostic results
mode is started.
The indication terminates after 5 minutes. Turning the igni-
tion switch from
"OFF" to "ON" resumes blinking the indi-
cation. During the SLlP indicator lamp operation shown
above,
TCS OFF indicator lamp and ABS warning lamp are
lit.
sis.
10. Rerun the self-diagnostic results mode to verify that the mal-
function codes have been erased.
0 When the malfunction codes have been erased, the start
code No.
12 is only indicated.
11. Disconnect the check terminal from the ground. The self-diag-
nostic results mode is now complete.
12. Drive vehicle at approx. 30 kdh for approx. 1 minute, and then
check that the
TCS OFF indicator lamp, the SLlP indicator
lamp
and the ABS warning lamp are OFF.
13. Turn the ignition switch "OFF.

TCS/ABS SYSTEM
Self-diagnosis for TCSfABS Control Unit
Control System (Cont'd)
MALFUNCTION CODE/SYMPTOM CHART I I I
75, 'I:
'2: '3: '4:
'5:
Fail-safe operation is not activated. A signal from control unit suspends TCS and ABS control operation. Brakes operate
conventionally and the vehicle operates in the same manner as a vehicle without the TCS. After specified battery voltage
resumes, the TCS
OFF indicator lamp and the ABS warning lamp go off, allowing for TCS and ABS control operation.
TCS operation only stops and fail-safe operation is activated, allowing for ABS control operation.
Malfunction is detected only when TCS is in operation.
When there are malfunctions in the self-diagnostic check terminal circuit (terminal
4 of the data link connector for CONSULT)
and SLlP indicator lamp circuit, fail-safe operation is not activated.
Some malfunctions in the
TCS/ABS
control unit cause the SLlP indicator lamp and the
ABS warning lamp to go off sepa-
rately.
Malfunc-
tion code
No.
12
21 22
25
26
31
32
35
36
41
42
45
46
55
56
57
58
61
63
71
75
80
83
84
85
86
NO indi-
cation
(no blink-
ing)
NOTE:
When the
80, 83,
84, 85 or 86 is indicated, perform the self-diaqnosis for ECM-TCM or ECM.
Check
item
Normal
Front right wheel sensor (open-circuit)
Front right wheel sensor (short-circuit)
Front left wheel sensor (open-circuit)
Front left wheel sensor (short-circuit)
Rear right wheel sensor (open-circuit)
Rear right wheel sensor (short-circuit)
Rear left wheel sensor (open-circuit)
Rear left wheel sensor (short-circuit)
Front right outlet solenoid valve and circuit
Front right inlet solenoid valve and circuit
Front left outlet solenoid valve and circuit
Front left inlet solenoid valve and circuit
Rear outlet solenoid valve and circuit
Rear right inlet solenoid valve and circuit
Battery voltage (low)
Throttle control unit system or circuit for the corn-
munication
line between TCSIABS control unit
and
throttle control unit
Actuator motor and motor relay circuit
Actuator relay circuit
TCSIABS
control
unit
Total control signal (multiple signal) for engine,
IVT
and TCS/ABS
Engine speed signal
Monitoring of total control signal (multiple signal) for
engine,
AfT and TCS/ABS
Engine system component fuel condition
Incomplete start process of total control signal (mul-
tiple signal) for engine,
AfT and TCSIABS
Continuous start process of total control signal
(multiple signal) for engine, and
TCS/ABS
Remains OFF: Data link connector circuit
Remains ON: SLIP indicator lamp circuit shorted,
TCSIABS
control unit or self-diagnostic check termi-
nal circuit open
malfunction code No. 58 is indicated, perform the Detection
Engine
running
-
0 -
0
-
0 -
0 -
0
0
0
0
0
0
0
0
0
0
0
0
-
0
0
0
0
0
0
throttle control time
In driving
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 -
0'3
0
0
0
0
0
0
unit
a Fail-safe
operation
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-'I
0
0
0
0
0
0
0
0
0
0
-'4
-'4
code Nos.
ABS
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-*2
0
0
05
-
-
-
-
-
-
-
0
self-diagnosis. Lamp
ON
TCS OFF
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-
0
When the SLlP
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0'5
0
0
0
0
0
0
-
0
malfunction

ELECTRIC SUPER HICAS
Control
Unit Input/Output Signal Specifications
USING CIRCUIT TESTER
Terminal No.
Check item Specification
When control unit is disconnected
: Continuity exists.
Control unit ground circuit
Motor driving output signal
When ignition switch is
ON : Power supply voltage
(In fail-safe mode
: OV)
Motor voltage
When vehicle speed is
0 krn/h : Approx. 4.4 - 6.6V
When vehicle speed is
100 km/h : Approx. 2.4 - 3.6V EPS solenoid driving signal
Battery voltage
I Power supply voltage
Data link connector for CONSULT
(TX) I -
Engine speed signal Measure
tachometer driving signal.
Refer to EC section YECM (TCM) Input/Output Signal
Reference
Value7
.
When ignition switch is ON : Power supply voltage
When ignition switch is OFF
: OV Ignition voltage
Body
/ ground HlCAS waming
lamp When HlCAS warning
lamp is ON
: Approx. OV
When
HlCAS
warning
lamp
is
OFF : Approx. 12V
When ignition switch is ON : Approx. 12V
(In fail-safe mode : Approx. OV)
Output
signal for driving motor relay
Data link connector for CONSULT
(RX) I -
Stop lamp switch signal
(Send brake pedal operation signal to control unit.) When
pedal is depressed : Power supply voltage
When
pedal is not depressed
: OV
Continuity exists.
v Steering angle sensor 2
Steering angle sensor 1
Body
ground When steering wheel
is turned, the voltage changes
between 0 and 5V.
Ground
circuit for rear steering angle sensor
Output signal of rear steering angle sensor
I When neutral : Approx. 2.4V
-
Neutral signal of rear steering angle sensor
When ignition switch is ON
When ignition switch is
OFF
--
When neutral : Appro~. 5V
: Approx. 5V
: Approx. OV Power supply for rear steering angle sensor

ELECTRIC SUPER HlCAS
Control Unit
Input/Output Signal Specifications
(Cont'd)
USING CONSULT
The displayed output signals represent the control unit com-
puted data. If the output circuit (harness) should
be open,
correct values may be displayed.
Monitor item
VHCL SPEED SE
[km/hj
STOP LAMP SW
[ON-OFF] Data monitor
I Condition
Specification
--
STEERING ANG Steering
wheel is turned right Steering angle (degrees) mea-
[R/Ll or left. sured from neutral position
NEUTRAL SIG Steering wheel is in neutral When neutral: ON
[ON-OFF] position
or turned right or left. When
turned (right or left): OFF
Brake pedal operation Check
item
Vehicle is running or driving
wheels are turning.
Steering angle sensor circuit
Approximately
equal to speed-
ometer reading
When pedal is depressed: ON
When pedal is not depressed:
I OFF
In neutral position:
Approx.
2.4V Vehicle
speed sensor circuit
Stop lamp switch circuit
ENGINE SPEED
[r~ml
1"l I Actuator is operating in active I In right lock position:
test. Engine
is running.
Approx. 4.4V
in left lock position:
Approx.
0.4V
Rear steering angle sensing
system
Approximately
equal to tachom-
eter reading
POWER STR SOL
[A1
Wiring
in ECM-HICAS control
unit
MOTOR CURRENT
PI
Vehicle speed is changed from
0 to 100 krnh.
HlCAS RELAY
[ON-OFF]
FAILSAFE
[ON-OFF] At
0 km/h:
Approx. 1.1 0A
At
100 krn/h: Approx. 0.48A
WARNING LAMP
[ON-OFF] System related to power steer-
ing solenoid output signal
RR ST
ANG-VOL
[Vl
MOTOR VOLTAGE
[vl
Actuator is operating in active
test.
Ignition switch is ON or engine
is running.
I Power supply system for
OK
if output current is detected
during operation Motor
and its power supply
system
1 signal from control unit
When ignition
switch is ON: ON
Not in operation HICAS
motor relay
System related to relay driving
Check malfunctioning parts
using self-diagnosis and data
monitor.
Approx.
5V
When warning lamp is ON: ON
When warning lamp is OFF:
OFF
Rear steering angle sensing
system Warning
lamp circuit
Power supply voltage Motor power
supply system
C/U
VOLTAGE
[VI Control unit power supply cir-
cuit
Ignition
switch is ON or engine
is running. Power
supply voltage

ELECTRIC SUPER HICAS
Trouble Diagnosis
with CONSULT (Cont'd)
connector for
'@g SELECT DlAG MODE
SELF-DIAG RESULTS i
DATA MONITOR
ACTIVE TEST
ECM PART NUMBER
u
1 I lhil SELECT MONITOR ITEM I 1
SELECTION FROM MENU
I Il
I
START I
ACTIVE TEST PROCEDURE
After connecting CONSULT to data link connector, start the
engine.
Touch "START", "HICAS and "ACTIVE TEST".
Touch 'SIMULATE" and "SELECT MONITOR ITEM".
Turn the steering wheel right or left to make the rear actuator
operate.
Reference values in normal condition
-- -
0" (Neutral) I 2.4V I 2.4V I No (Approx OV)
Steering angle
sensor
ECM PART NUMBER
Rear steering
angle main sensor
--
R 90"
L 90"
After connecting CONSULT to data link connector, turn ignition
switch ON.
Touch "START', "HICAS" and "ECM PART NUMBER7'.
Part number printed on the control unit label and part number
shown on the CONSULT screen are as follows:
2-door model: 28505
AAI
00
4-door model: 28505 AAll 0
Trouble Diagnosis with Self-diagnosis
Rear steering
angle sub-sensor
4.4V
0.4V
DESCRIPTION
If the system detects some error while vehicle is running, it notifies
the driver of a malfunction
by turning ON the HICAS warning lamp,
and at the same time, it halts the normal control and enters the
fail-safe mode.
Motor current
SELF-DIAGNOSIS PROCEDURE
4.4V
0.4V
1. Start the engine.
2. Within 10 seconds after the engine has started, turn the steer-
ing wheel more than
20" right-to-left and repeat this
5 times or
more, and then depress the brake pedal
5 times or more.
Yes (Variable)