stop start NISSAN GT-R 1998 User Guide

ANTI-LOCK BRAKE SYSTEM
CONSULT (Cont'd)
r I I ABS motor / a UCTIl..!E TEST fj I I Touch "ON" and "OFF on the screen to check that ABS motor - - - - -. . -
relay and ABS actuator relay operate as follows:
- - - - -- --
Operation
ABS actuator relay
brake pedal travel limit may change. This is a normal condition.
"TEST IS
STOPPED" message is displayed 10 seconds after
ABS motor relay I ON
1 the operation is started.
I
ON
ON
OFF OFF G9
ON
EG
If the active test is conducted with brake pedal depressed, the

ANTI-LOCK BRAKE SYSTEM
Self-diagnosis
DESCRIPTION
When a problem occurs in the ABS, the ABS warning lamp on the
instrument panel comes on. To actuate the self-diagnostic results
mode, ground the self-diagnostic check terminal
4 located on the
data
link
connector for
CONSULT. The ABS warning lamp, then,
flashes and indicates the location of the malfunction.
SELF-DIAGNOSIS PROCEDURE
1. Collect information on the concern from the customer, and then
perform basic inspections.
2. Drive vehicle at approx. 30 km/h for approx. 1 minute.
3. Stop vehicle and start diagnosis.
4. Turn ignition switch "OFF'.
5. Ground the self-diagnostic check terminal 4.
6. Turn ignition switch "ON" to start the self-diagnostic results
mode.
CAUTION:
Keep terminal 4 grounded during self-diagnosis.
Do not depress brake pedal. (Self-diagnosis would not
start.)
Do not start engine. (Self-diagnosis would not start.)
7. After 3 or 4 seconds, ABS warning lamp starts blinking to indi-
cate the malfunction code No.
The indication terminates after 5 minutes. Turning the ignition
switch from
"OFF" to "ON" resumes blinking the indication.
8. Verify the location of the malfunction with "MALFUNCTION
CODUSYMPTOM CHART", BR-16. Then make the necessary
repairs.
9. After the malfunctions are repaired, erase the malfunction
codes stored in the control unit. Refer to "HOW
TO ERASE
SELF-DIAGNOSTIC RESULTS" on the next page.
10. Rerun the self-diagnostic results mode to verify that the mal-
function codes have been erased.
11. Disconnect the check terminal from the ground. The self-diag-
nostic results mode is now complete.
12. Drive vehicle at approx. 30 km/h for approx. I minute, and then
check that the ABS warning lamp is off.
HOW TO READ SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
Determine the code No. by observing the time and the fre-
quency that the
ABS warning lamp blinks ON and OFF.
When multiple malfunctions occur at a time, up to three code
numbers can be stored; the latest malfunction will be indicated
first.
The indication begins with the start code No. 12. A maximum
of three code numbers appear in the order of the latest one
first. The indication then returns to the start code No.
12 to
repeat.
The start code No. 12 is only indicated repeatedly when there
is no malfunction.

ANTI-LOCK BRAKE SYSTEM
Self-diagnosis (Cont'd)
Example: Code No. 25 Front left wheel sensor (open-ccrcuit)
lnd~cat~on
s:arl
Start code No. i2
Unit: seconds BRG1185D
ABS warnq lamp ON -
A9S warnrng lamp OFF
Self-d~agnosis complete , C ABS warning lamp !
I i I I I
................ &. j(j(?.:e~o"dd~i!~?!!f!!. . -----... .-.---.--. iiii rase 1 12.5 seconds I mode
Malfunct~on
memory Malfunction memory is Nn. erase mode starts. Is erased BRG0057C
Tens d~g~ts Un~ts digits Code No 25 I I - I
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
r--------- -T---t----t-l-T-l-
1. Turn the ignition switch "ON" and start the engine.
-.
---------- -I--I--t--l-i-"I
2. Drive the vehicle at approx. 30 kmh for approx. 1 minute to
check that there is no other malfunction.
ST
3. Stop the vehicle.
4. Turn the ignition switch "OFF'.
5. Ground the self-diagnostic check terminal. RS'
6. Turn the ignition switch "ON" to start the self-diagnostic results
-
-.
3 06 0.9 03C303 3.3 06 0.6 0.6 09 050303030305030303
-----
mode.
CAUTION:
c--
Do not depress the brake pedal during self-diagnosis. Do not
start the engine. (The self-diagnosis
would not start.)
7. The ABS warning lamp starts to blink 3 or 4 seconds after the EL
self-diagnostic results mode is started.
8. Under the self-diagnostic results mode, the malfunction $jD
memory erase mode starts when the check terminal is discon-
nected from the ground.
9. Ground the check terminal 3 times or more in succession
within 12.5 seconds after the erase mode starts. (Each ground-
ing must
be 1 second or longer.)
10. Disconnect the grounding cable from the check terminal to
erase the malfunction memory and complete the
self-diagno-
sis. The ABS warning lamp
, then, turns off.
11. Turn the ignition switch
"OFF'.

TCSIABS SYSTEM
System
Description
ABS FUNCTION
During ABS operation, the brake pedal pulsates along with a mechanical noise. This ensures that the ABS
is working properly. mP
When starting up the engine or immediately after the vehicle starts to run, the brake pedal pulsates and G'
a motor noise from the engine compartment can be heard. They are caused by the ABS operation check
and should not be considered abnormal.
A vehicle with the ABS may stop in a longer distance than a vehicle without the ABS when the brake is
EC
applied on a bad road, gravel road, or deep fresh snow.
TCS FUNCTION
TCS/ABS control unit monitors the speed of the driving wheels through 4 wheel speed sensors. If driving
wheel slip is detected, fuel to the engine is cut
ol
and the throttle valve is adjusted so that the engine
a
torque is reduced. On vehicles with automatic transmission, transmission shift schedule is also changed
to control the rear wheel driving torque, which results
in the reduction of wheel slip. This system enables
the throttle valve to be controlled so that optimum engine torque can be achieved in accordance with the
driver's acceleration request.
The driver may not feel satisfied with acceleration on some road surfaces. This poor acceleration occurs
because the operating TCS gives priority to maintaining optimum traction. Therefore, this condition should
R8
be considered normal.
When shiftdown is made or the acceleration pedal is depressed while the vehicle is driven on the road
surface that has different friction coefficients, the TCS may operate temporarily.
r-- 4 Lrd[-i
On vehicles with manual transmission, the SLlP indicator lamp and the TCS OFF indicator lamp may light
up when the engine is about to stall in the conditions shown below.
If the lamps go off when engine speed
increases, there is no problem in the system.
At start, the engine almost stalls and the engine speed is much lower than the idle speed.
The vehicle is driven at an extremely low speed with a high-speed gear engaged.
The clutch has been engaged until the vehicle almost stops. 8D
FAIL-SAFE FUNCTION
ABS system
If any malfunction is detected in the system, the ABS warning lamp, the TCS OFF indicator lamp and the SLlP
indicator lamp in the instrument panel is turned on with the TCSIABS deactivated and the vehicle's brake sys-
tem reverts to normal operation.
TCS system
If any malfunction is detected in the system, both the SLlP indicator lamp and the TCS indicator lamp on the
instrument panel light up and the TCS is shut down. The vehicle operates in the same manner as a vehicle
without the
TCS, while the ABS is operational.
If there is a malfunction in the throttle control system, the TCS becomes inoperative while the ABS
remains functional.
When fail-safe operation is activated, perform the self-diagnosis procedure for the TCSIABS first.
Refer to
BR-27 for details.

TCS/ABS SYSTEM
Control Unit InputlOutput Signal Specifications
(Cont'd)
Terminal No.
Specifications'l
- - --
Check item (Refer-
ence)
- - -
Body
ground
-
Approx. 7V - - or higher Communication
line circuit between
TCSIABS control
unit and throttle
control unit
DKV
(throttle angle
output)
Acceleration pedal is released: approx. 1 ms (reference)
ABS warning lamp ABS warning
lamp
and circuit 4B3 warning lamp 0Nr2: Approx. OV
4BS
warning lamp 0FF72: Battery voltage (Approx. 12V)
cictuator
relay is activated (with engine running): Battery voltage
(Approx.
12V)
ktuator
relay is not activated (with fail-safe function activated and engine
70t
running): Approx.
OV
ABS warning lamp
and circuit,
ABS
actuator relay and
circuit
Actuator relay
monitor
48s
motor is running (in
CONSULT active test mode): Less than approx.
2V
4BS motor is stopped: Battery voltage (Approx. 12V)
TCS is not activated: ABS
motor, motor
relay and circuit
ABS
motor relay
Approx. 7V - -
OV I I Communication
line circuit between TCSfABS control
unit and throttle
control unit
DKR
(throttle
motor target angle
signal) Approx. 9 ms (Reference)
Front
right inlet
solenoid
Front right outlet
solenoid
4ctuator
is activated (in CONSULT active test mode), or actuator relay is
lot
activated (with fail-safe function activated and engine not running):
4pprox.
OV
4ctuator
is not activated and actuator relay is activated (with vehicle
stopped and engine running): Battery voltage (Approx.
12V)
Rear inlet solenoid
Rear outlet
sole- ABS solenoid and
circuit
Front left inlet
solenoid
Front left outlet
solenoid
Battery gnition switch
ON: Baitery voltage
(Approx. 12V) Control
unit power
supply circuit
'1: Do not force to oDen a connector terminal when usina a circuit tester for ins~ection. '2: ABS warning lamp ON: When the ignition switch is t6ned ON (before startirig the engine) or a malfunction is detected
ABS warning lamp OFF: When the engine has started (with the system in normal condition)
'3: Tire pressure must be in accordance with specification. '4: TCS OFF indicator lamp ON: When the ignition switch is turned ON (before starting the engine), a malfunction is detected,
or TCS OFF switch is turned ON TCS OFF indicator lamp OFF: When the engine has started (with the system in normal condition) and the TCS OFF switch
is off '5: SLlP indicator lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected
SLlP
indicator lamp OFF: When the engine has started (with the system in normal condition) and the TCS is inoperative

TCS/ABS SYSTEM
CONSULT for TCS/ABS Control Unit Control
System
CONTROL UNIT PART NUMBER
The part number that is shown on the control unit label and CON-
SULT
A/T model: 47850 AA310
M/T model: 47850 AA110
SELF-DIAGNOSIS PROCEDURE rn
Collect information on the concern from the customer, and then
perform basic inspections.
Turn ignition switch OFF and connect CONSULT connector to
data link connector for CONSULT on the vehicle.
ST
Start engine and drive vehicle at approx. 30 km/h for approx.
1 minute.
Stop vehicle with engine running and touch "START", "ABS"
38
and "SELF-DIAG RESULTS" sequentially on the CONSULT
screen.
If "START" is touched immediately after engine is started y;rjn
or ignition switch is turned on, "ABS" may not be dis-
played on "SELECT SYSTEM" screen. To display "ABS", E~
repeat the self-diagnosis procedure from the beginning.
Self-diagnosis results are displayed on the screen. (Touch
"PRINT' to print out the self-diagnosis results,
if necessary.) 8~ If "NO FAIL" is displayed, inspect the SLlP indicator lamp, the
TCS OFF indicator lamp and the ABS warning lamp. Refer to
the previous page.
Perform appropriate inspection from the self-diagnostic results
mode and repair or replace faulty parts.
Start engine and drive vehicle at approx.
30 km/h for approx.
1 minute.
Recheck to ensure that there is no other malfunction.
Turn ignition switch OFF to prepare for erasing the trouble
stored in memory.
Start engine and touch "START",
"ABS", "SELF-DIAG
RESULTS" and "ERASE" sequentially on the CONSULT
screen to erase the trouble stored in memory.
If the trouble stored in memory is not erased, repeat step
6.
Drive vehicle at approx. 30 krn/h for approx. 1 minute and then
confirm that the TCS OFF indicator lamp, the
SLlP indicator
lamp, and the ABS warning lamp are OFF.
TCS OFF switch is not in cancel condition.

TCSfABS SYSTEM
CONSULT for
TCSfABS Control
Unit Control
System (Cont'd)
Diagnostic item
LAN CIRCUIT
1
LAN CIRCUIT 2
Diagnostic item is detected when ... I Check item
NOTE:
If "NO FAILn is displayed as a result of the CONSULT self-diagnosis when the ABS warning lamp is lit, inspect the engine speed
signal circuit.
If "ABSn is not displayed on "SELECT SYSTEM" screen, check ABS control unit and data link connector circuit, and make sure of the CONSULT card number. If "ENGINE SYSTEM", "LAN SIGNAL 1". "LAN SIGNAL 2", "LAN SIGNAL 3, "LAN CIRCUIT 1" or "LAN CIRCUIT 2" is displayed
on the screen, perform the self-diagnosis for the
ECM.TCM
or ECM.
If "THROlTLE CONTROLLER COMMUNICATIONn is displayed on the screen, perform the self-diagnosis for throttle control unit.
Total control signal (multiple signal) for engine, All and TCSIABS is abnormal (open or
shorted communication harness,-faulty connections, abnormal TCSIABS control unit or
ECM.TCM
or ECM).
ECM.TCM
or ECM power is cut
off or decreased for 2 seconds or longer.
Total control signal (multiple signal) for engine,
ArT and TCSIABS is suspected to be
interrupted (open or shorted communication harness, faulty connections, abnormal
TCS/ABS
control unit or ECM TCM or ECM).
ECM.TCM or ECM power is cut off or decreased for 2 seconds or longer.
DATA
a
1.
2.
3.
4.
5.
a
signal 1, 2
(multiple sig-
nal) for
and
TCSI
ABS
MONITOR PROCEDURE
Refer to CONSULT Instruction Manual for details on data
monitor function.
Turn ignition switch OFF.
Connect CONSULT connector to data link connector for
CON-
SU LT.
Turn ignition switch
ON.
Touch "START" on CONSULT screen.
Touch "ABS" on CONSULT screen.
If "START" is touched immediately after engine is started
or ignition switch is turned ON, "ABS" may not be dis-
played on "SELECT SYSTEM" screen. To display "ABS",
repeat the data monitor procedure from the beginning.
Touch "DATA MONITOR".
Touch "SETTING" to set recording condition.
Touch "AUTO TRIG", "LONG TIME" and then
"ENTER".
Return to "SELECT MONITOR ITEM" screen and touch "C/U
INPUT ITEM",
"ALL SIGNALS" or "SELECTION FROM
MENU". Refer to "DATA MONITOR MODE" on the next page.
10. Touch "START".
11. Display data monitor.
12. If necessary, sequentially touch "REC START, "REC STOP",
"DATA DISPLAY", "NUMBER PRINT" and "PRINT" to print out
the data.

TCS/ABS SYSTEM
CONSULT for TCS/ABS Control Unit Control
System (Cont'd)
9. "ACTIVE TEST' screen is displayed.
ABS solenoid valve
a To check that ABS solenoid valves (inlet and outlet) ooerate in
I I I - --
': Solenoid valve stays ON for 1 to 2 seconds after touching the key, and then
turns OFF. =
the following manner, touch "UP", "KEEP" and "DOWN" on the @
screen while observing the monitor.
If the active test is conducted with brake pedal depressed, the ; <
brake pedal travel limit may change. This is a normal condition.
"TEST IS STOPPED" message is displayed 10 seconds after
Y
the operation is started. ST
a If the active test needs to be performed again after "TEST IS
STOPPED" is displayed, repeat step 8. RS
Operation
IN ABS
SN
OUTABS SN
ABS motor
Touch "ON" and "OFF' on the screen to check that ABS motor EL
relay and ABS actuator relay operate as follows:
UP
OFF
OFF
Operation ON
@
KEEP
ON
OFF
ABS actuator relay
ABS
motor relay DOWN
Ee
ON
ON'
A'
a If the active test is conducted with brake pedal depressed, the
brake pedal travel limit may change. This is a normal condition.
a "TEST IS STOPPED" message is displayed 10 seconds after
the operation is started.
ON
ON OFF
ON
OFF

TCS/ABS SYSTEM
Self-diagnostic check ter (Terminal 4 of data link c
Data link connector for CONSULT
Self-diagnosis for TCSfABS Control Unit
Control System
SELF-DIAGNOSIS PROCEDURE
1. Collect information on the concern from the customer, and then
perform basic inspections.
2. Drive vehicle at approx. 30 km/h for approx. 1 minute.
3. Stop vehicle and start diagnosis.
4. Turn ignition switch "OFF.
5. Ground the self-diagnostic check terminal 4 on the data link
connector for CONSULT.
6. Turn ignition switch "ON" to start the self-diagnostic results
mode.
CAUTION:
Keep terminal 4 grounded during self-diagnosis. Do not
depress brake pedal. Do not start engine. (Self-diagnosis
would
not start.)
When SLlP indicator lamp does not start blinking, check
TCSfABS
control unit power supply circuit and ground
circuit.
7. The SLlP indicator lamp starts blinking to indicate the malfunc-
tion code No.
3 or 4 seconds after the self-diagnostic results
mode is started.
The indication terminates after 5 minutes. Turning the igni-
tion switch from
"OFF" to "ON" resumes blinking the indi-
cation.
During the SLIP indicator lamp operation shown above,
TCS
OFF indicator lamp and ABS warning lamp are lit.
8. Vsrify the location of the malfunction with "MALFUNCTION
CODUSYMPTOM
CHART", BR-36. Then make the necessary
repairs.
9. After the malfunctions are repaired, erase the malfunction
codes stored
in the control unit. Refer to "HOW TO ERASE
SELF-DIAGNOSTIC RESULTS on the next page.
10. Rerun the self-diagnostic results mode to verify that the mal-
function codes have been erased.
When the malfunction codes have been erased, the start
code is only indicated.
11. Disconnect the check terminal from the ground. The self-diag-
nostic results mode is now complete.
12. Drive vehicle at approx. 30 km/h for approx. 1 minute, and then
check that the
TCS OFF indicator lamp, the SLlP indicator
lamp and the ABS warning lamp are OFF.
HOW TO READ SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
Determine the code No. by observing the time and the fre-
quency that the SLlP indicator lamp flashes ON and OFF.
Refer to the next page.
When multiple malfunctions occur at a time, up to three code
numbers can
be stored; the latest malfunction will be indicated
first.
The indication begins with the start code No. 12. After that a
maximum of three code numbers appear in the order of the
latest one first. The indication then returns to the start code No.
12 to repeat.
The start code No.
12 is only indicated repeatedly when there
is no malfunction.

TCS/ABS SYSTEM
Self-diagnosis for TCS/ABS Control Unit
control System (Cont'd)
Example: Code No. 25 Front left wheel sensor (open-circutt)
lnd~cat~on
start Start code No.
12
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
(Malfunction codes)
1. Turn the ianition switch "ON" and start the engine.
ABS warnlng lamp - ON
ABS warning lamp
OFF
2. Drive the iehicle at approx. 30 km/h for appfox. 1 minute to
check that there
is no other malfunction.
3. Stop the vehicle and turn the ignition switch "OFF'. I88
4. Ground the self-diagnostic check terminal 4 on the data link
connector for CONSULT.
5. Turn the ignition switch "ONn to start the self-diagnostic results /,%@A
mode.
I---------- -------------- -?-I 3 06 0.9 03C303 3 3 06 3.6 06 09 030303030303030303
Unit: seconds BRG1185D
Tens drglts Units drgits Code No. 25
I -----l
7. Under the self-diagnostic results mode, the malfunction
memory erase mode starts when the check terminal
is discon-
nected from the ground.
8. Ground the check terminal 3 times or more in succession
-.
self-d~agnosts complete
SLlP ndicator lamp i
I ON r
f OFF - c 4 i
ground J Erase -- - - - - - - - - -i - - - - ---f2.i geconds-- - - - - - - .. t mode
Malfunct~on
memory
Malfunct~on
memory
IS erase mode starts. 1s erased. BRZOO~~D
within 12.5 seconds after the erase mode starts. (Each ground-
ing must be
2 seconds or longer.)
9. Disconnect the grounding cable from the check terminal to
erase the malfunction memory and complete the
self-diagno-
-----
CAUTION:
Keep terminal 4 grounded during self-diagnosis. Do not EL
depress the brake pedal during self-diagnosis. Do not start the
engine.
6. The SLIP indicator lamp starts blinking to indicate the malfunc- SD
tion code No. 3 or 4 seconds after the self-diagnostic results
mode is started.
The indication terminates after 5 minutes. Turning the igni-
tion switch from
"OFF" to "ON" resumes blinking the indi-
cation. During the SLlP indicator lamp operation shown
above,
TCS OFF indicator lamp and ABS warning lamp are
lit.
sis.
10. Rerun the self-diagnostic results mode to verify that the mal-
function codes have been erased.
0 When the malfunction codes have been erased, the start
code No.
12 is only indicated.
11. Disconnect the check terminal from the ground. The self-diag-
nostic results mode is now complete.
12. Drive vehicle at approx. 30 kdh for approx. 1 minute, and then
check that the
TCS OFF indicator lamp, the SLlP indicator
lamp
and the ABS warning lamp are OFF.
13. Turn the ignition switch "OFF.