trunk release NISSAN MURANO 2013 2.G User Guide

Black plate (163,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
prevent the Intelligent Key from being left in
the vehicle.
. The door handle request switch is opera-
tional only when the Intelligent Key has been
detected by the Intelligent Key system.
. To prevent the Intelligent Key from being left
inside the vehicle or the trunk, make sure you
carry the key with you and then lock the
doors or the trunk.
. Do not pull the door handle before pushing
the door handle request switch. The door
will be unlocked but will not open. Release
the door handle once and pull it again to
open the door.
. The Intelligent Key system (opening/closing
doors with the door handle request switch)
can be set to remain inactive on the center
display (if so equipped). (See “Vehicle
information and settings” in the “4. Monitor,
heater, air conditioner, audio, phone and
voice recognition systems” section.)
SPA2408
INTELLIGENT KEY OPERATIONGUID-11F409E1-2083-4E3E-98C3-276AB17A6B02You can lock or unlock the doors without taking
the key out from your pocket or bag.
SPA2779
SPA2780
Hardtop models
Pre-driving checks and adjustments3-11
Condition:

Black plate (169,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA2867
Type C
*1LOCK button
*2UNLOCK button
*3Power lift gate button(if so equipped)
*4PANIC button
*5TRUNK button(CrossCabriolet models)
HOW TO USE REMOTE KEYLESS
ENTRY SYSTEM
GUID-C6C8F65F-3152-4763-BF0F-A4447FDA547FWhen you lock or unlock the doors or the lift
gate/trunk lid, the hazard indicator will flash and
the horn (or the outside chime) will sound as a
confirmation. For details, see “Setting hazard
indicator and horn mode” later in this section.
Locking doorsGUID-8CBF74EB-4EC8-465A-B09B-2CA410A11EC01. Move the selector lever to the P (Park)position and push the ignition switch to the
OFF position. Make sure you carry the
Intelligent Key with you.*
2. Close all the doors and lift gate.
3. Push the LOCK
button*1.
4. All the doors and the lift gate will lock.
5. The hazard indicator flashes twice and the horn chirps once.
*: Doors will lock while the ignition switch is in the ACC or ON position.
Unlocking doorsGUID-07D2F8A3-E183-47DE-B2BB-5F0B2765BABE1. Push the UNLOCKbutton*2once.
2. The hazard indicator flashes once. The
driver’s door will unlock.
3. Push the UNLOCK
button*2again
within 1 minute. 4. The hazard indicator flashes once again. All
the doors and the lift gate will unlock.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute after pushing the UNLOCK
button
*2while the doors are locked. If during this 1-
minute time period, the UNLOCK
button*2
is pushed, all doors will be locked automatically
after another 1 minute.
. Opening any door (including the lift gate) or
trunk
. Pushing the ignition switch
Opening windowsGUID-A6DE3912-EF46-4CEA-887C-286260C70F8FThe UNLOCKbutton*2operation also
allows you to open the window that is equipped
with the automatic open/close function. (See
“Power windows” in the “2. Instruments and
controls” section) .
To open the windows, push the door UNLOCK
button*2for about 3 seconds after the
door is unlocked.
To stop opening, release the UNLOCK
button*2.
Windows cannot be closed using the button on
the Intelligent Key.
If the window open operation is stopped in mid-
operation while pushing the UNLOCK
button*2, release and push the UNLOCK
Pre-driving checks and adjustments3-17
Condition:

Black plate (177,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA1915
LIFT GATE RELEASEGUID-1D614743-17EC-4673-B778-F929F5E10CB9If the lift gate cannot be opened due to a
discharged battery, follow these steps.
1. Remove the cover inside of the lift gate witha suitable tool.
2. Move the lever toward the direction
*Aas
illustrated to open the lift gate.
Have the vehicle checked by a NISSAN dealer.
GUID-2C264EE5-CF00-4D99-8287-BE0FA9532E1E
WARNING
. Do not drive with the trunk lid open.
This could allow dangerous exhaust
gases to be drawn into the vehicle.
See “Exhaust gas (carbon monox-
ide)” in the “5. Starting and driving”
section of this manual.
. Closely supervise children when
they are around cars to prevent
them from playing and becoming
locked in the trunk where they could
be seriously injured. Keep the car
locked, with the trunk closed, when
not in use, and prevent children’s
access to Intelligent Keys.
SPA2868
TRUNK LID RELEASE SWITCHGUID-3E3F75C6-3DEC-4CB3-AB7F-5D7232A3354CThe trunk lid release switch*Ais located on
the instrument panel.
To open the trunk lid, push the release switch
down as illustrated. To close, push the trunk lid
down.
Pre-driving checks and adjustments3-25
TRUNK LID (CrossCabriolet models)
Condition:

Black plate (178,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-26Pre-driving checks and adjustments
SPA2866-A
TRUNK OPEN REQUEST SWITCHGUID-B01B03F7-E6F4-4880-AF56-804BF02D2CC4The trunk lid can be opened by pushing the
trunk open request switch
*Awhen the
Intelligent Key is within the operating range of
the trunk lock/unlock function regardless of the
inside lock knob position. (See “Intelligent Key
system” earlier in this section.)
TRUNK BUTTONGUID-BBA61B35-8253-481A-BABD-2C8031AD5525The trunk lid can be opened by pushing the
TRUNK button
on the Intelligent Key for
more than 1 second.
SPA2871
OPENING WITH KEYGUID-A6A5B4FC-5FBC-4C5F-8A27-A149CEEDAF32To open the trunk lid, insert the mechanical key
to the trunk key cylinder and turn the key to the
right side of the vehicle. To close, remove the
key and push the trunk lid down.
SPA2869
TRUNK RELEASE POWER CANCEL
SWITCH
GUID-4D40CB74-0EE0-44CF-9D72-61FB52259054When the switch located inside the glove box is
in the OFF position
*A, the power to the trunk
lid will be canceled and the trunk lid cannot be
opened by the trunk lid release switch, the trunk
open request switch with the Intelligent Key
carried with you or the TRUNK button on the
Intelligent Key.
When you have to leave the vehicle with a valet
and want to keep your belongings safe in the
glove box and the trunk, push this switch to OFF
and lock the glove box with the mechanical key.
Then leave the vehicle and the Intelligent Key
with the valet and keep the mechanical key with
Condition:

Black plate (179,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
you.
See “Keys” earlier in this section.
To connect the power to the trunk lid, push the
switch to the ON
*Bposition.
SPA2870
INTERIOR TRUNK LID RELEASEGUID-76617E49-69A3-42A3-B4CE-6BA318A11DE5
WARNING
Closely supervise children when they
are around cars to prevent them from
playing and becoming locked in the
trunk where they could be seriously
injured. Keep the car locked, with the
trunk lid securely latched, when not in
use, and prevent children’s access to
Intelligent Keys.The interior trunk lid release mechanism allows
opening of the trunk lid in the event that people
become locked inside the trunk or in the event of
the loss of electrical power such as a dis-
charged battery.
Releasing inside the trunkGUID-AF4D5EDF-174E-4F6F-B198-B456683E28BDTo open the trunk lid from the inside, pull the
release handle
*1until the lock releases and
push up on the trunk lid. The release lever is
made of a material that glows in the dark after a
brief exposure to ambient light.
The handle is located on the back of the trunk lid
as illustrated.
Pre-driving checks and adjustments3-27
Condition:

Black plate (184,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-32Pre-driving checks and adjustments
.Do not place anything in the top
storage area. The top will not fit
there properly, and this could da-
mage the top and/or the vehicle
body.
. Do not sit or place anything on the
top, rear parcel shelf, inner flaps,
storage lid and trunk lid, especially
when the top is being operated. The
top may be damaged.
. Do not drive the vehicle with the top
partially opened. Always make sure
the top is either fully opened or
closed before driving.
. Secure items so that they cannot be
blown from the vehicle while driving
with the top open.
. Do not operate the top manually
except for emergency cases. Manual
operation may damage the top.
. Be sure to fully open or fully close
the top. Do not release the switch
half way through the roof opening
or closing process. If the top is only
partially opened, significant da-
mage to the top could occur.
. Do not operate the top if the dual
pop-up roll bars have been acti- vated. Extended dual pop-up roll
bars may interfere with top opera-
tion and could cause damage to the
top or the vehicle body.
Make sure the trunk lid is securely closed before
operating the top.
SPA2874
WHEN OPERATING THE TOPGUID-9783AAEB-D9EE-4150-9CAA-F03901BE51C6
WARNING
Keep hands and other parts of the body
away from moving parts such as the
top, storage lid, inner flap
*Aand
power windows.
Condition:

Black plate (190,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-38Pre-driving checks and adjustments
IF THE TOP DOES NOT OPEN OR
CLOSE ELECTRICALLY
GUID-17B75AAD-7BCD-4553-9A36-FB3FA5E49CAFIf you cannot operate the soft top with the
operating switch, first check whether all the
following operating conditions are met.
.Vehicle is stopped
. Ignition switch is ON (Run the engine when
operating the top.)
. The trunk is closed
. The selector lever is in a position other than
the R (Reverse) position
. The luggage cover is pulled out and hooked
so that the roof storage area is separated
from the trunk.
If the top still does not move under the above
conditions or has any system malfunction, see a
NISSAN dealer as soon as possible. When you
must close the top by yourself, in the event of
emergency or when an immediate dealer service
is not available, close the top manually accord-
ing to the procedures shown in this section.
When closing the soft top manually:
. Move the vehicle to a safe place, away from
traffic.
. Two people should perform this procedure,
as some of the top parts are extremely
heavy.
The top cannot be opened manually.
WARNING
. Do not drive with the top partially
opened.
. If the top cannot be operated prop-
erly, see a NISSAN dealer as soon
as possible to have your vehicle
checked.
CAUTION
The storage lid is extremely heavy. The
storage lid should be manually opened
or closed by two people.
1. Open the trunk lid. In the event of a
discharged battery, the secondary trunk
release mechanism should be operated.
(See “Trunk lid (CrossCabriolet models)”
earlier in this section.)
2. Open the top storage lid.JVP0036X
a. Remove the trunk light*1.
b. Remove the lower trim clips
*3and
remove the upper and lower trim pieces
*2.
c. Remove the two luggage cover hooks
*4
on the left and right side of the trunk.
Then disconnect the connector
*5on
the left side luggage cover hook.
d. Remove the clips
*6behind the luggage
cover hooks.
Condition:

Black plate (191,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVP0037X
Type A
JVP0097X
Type B
e. Release the storage lid locks.
Type A (models with cables):Pull back
the left and right side trim in the trunk room.
Pull the left and right cables
*Ain the
direction of the arrow using the wheel nut
wrench or suitable tool, and release the
storage lid locks
*B.
Type B (models without cables): Pull
back the left and right side trim in the trunk
room. Push linkage
*Aon the left and right
using the wheel nut wrench or suitable tool
to release the storage lid locks
*B.
CAUTION
Use gloves or a cloth to protect your
hands when releasing the storage lid
locks.
Pre-driving checks and adjustments3-39
Condition:

Black plate (192,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-40Pre-driving checks and adjustments
JVP0098X
Make sure that both the left and right locks
*Bare moved to the released position as
shown.
JVP0038X
f. Push and hold the lever*Ctoward the
front of the vehicle to release the storage
lid.
g. Close the trunk lid.
CAUTION
Make sure to close the trunk lid before
opening the storage lid. The storage lid
may contact the trunk lid and damage it.
JVP0039X
h. With two people, manually lift the storage lid by hand on the left and right side of
the vehicle at lid edge
*D.
Condition:

Black plate (404,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-14In case of emergency
SCE0871
6.Push the ignition switch to the “ACC”
position. Then turn the compressor switch
to the ON (−) position and inflate the tire up
to the pressure that is specified on the tire
and loading information label affixed to the
driver’s side center pillar if possible, or to the
minimum of 180 kPa (26 psi) . Turn the air
compressor off briefly in order to check the
tire pressure with the pressure gauge.
If the tire is inflated to higher than the
specified pressure, lower the tire pressure
by releasing air with the pressure release
valve. NOTE:
The compressor tire pressure gauge
may show a pressure reading of 87 psi
(600 kPa) for about 30 seconds while
inflating the tire. The pressure gauge is
indicating the pressure inside the sea-
lant can. When the sealant has been
injected into the tire the pressure
gauge will drop and indicate actual tire
pressure.
WARNING
.
To avoid serious personal injury
while using the emergency tire
puncture repair kit:
— Securely tighten the compressor
hose to the tire valve. Failure to
do so can cause the sealant to
spray into the air and get into
your eyes or on the skin.
. Do not stand directly beside the
damaged tire while it is being
inflated because of the risk of the
rupture. If there are any cracks or
bumps, turn the compressor off
immediately.
If the tire pressure does not increase to 180kPa (26 psi) within 10 minutes, the tire
may be seriously damaged and
the tire
cannot be repaired with this tire repair
kit. Contact a NISSAN dealer.
7. When the tire pressure is at the specified amount, turn the air compressor off. If the
pressure cannot be inflated to the specified
amount, the air compressor can be turned
off at the minimum of 180 kPa (26 psi) .
Remove the power plug from the power
outlet and quickly remove the hose from the
tire valve. Attach the protective cap and
valve cap. Properly stow the emergency tire
puncture repair kit in the trunk.
CAUTION
To avoid serious personal injury when
stowing the emergency tire puncture
repair kit:
.Keep the sealant bottle screwed
into the compressor. Failure to do
so can cause the sealant to spray
into the air and get into your eyes or
on the skin.
8. Immediately drive the vehicle for 10 minutes or 3 km (2 miles) at a speed of 80 km/h (50
MPH) or less.
Condition: