Display NISSAN NOTE 2016 Service Owners Manual

AV
INSPECTION AND ADJUSTMENTAV-181
< BASIC INSPECTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
Preparation of simplified target line
3. CONSULT work support Touch “FINE TUNING OF BIRDS- EYE VIEW” on the CONSULT screen.
4. On the CONSULT screen, touch “SELECT” button to select right or left camera and perform camera cali- bration as instructed below:
- If the marker on the screen deviates from Target li ne 1, touch “AXIS X” button and “AXIS Y” button to
adjust so that the marker is placed on the Target line 1.
- If Target line 2 is misaligned among the cameras, adjust each camera image to bring Target line 2 into a straight line.
CAUTION:
Never adjust the front camera and rear view cam era. Only adjust the right and left cameras.
Simplified target line adjustment method
5. Adjust right and left cameras. Touch "APPLY" on the CONSULT screen to display adjustment results.
6. After adjusting right and left cameras, check that the marker is properly placed on the screen and there is
no deviation in Target line 1.
NOTE:
• It can be initialized to the NISSAN factory default c ondition with “Initialize Camera Image Calibration”.
• The adjustment value is cancelled on this mode by performing “Initialize Camera Image Calibration”.
JSNIA0927ZZ
1. Target lines 12. Target lines 2
A. Approx. 30 cm (11.8 in) B. Approx. 1.0 m (39.3 in)
JSNIA0929ZZ
1. Target lines 1 2. Target lines 23. Marker for target line 1
4. Boundary between cameras 5. Crosshairs cursor
(mark indicated
the selected camera)
A. Adjustment method for target lines 1
(right) B.Adjustment method for target lines 2
(right)
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
INSPECTION AND ADJUSTMENTAV-183
< BASIC INSPECTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
6. Draw the lines of the points FL – RL and FR – RR with vinyl string, and fix it with packing tape.
7. Put a mark on the center of each axle, draw vertical lines to the lines of the points FL – RL and FR – RR from the marks on the center of the axle using a triangle scale, and then fix the lines using packing tape.
Target line preparation procedure 3
Perform “Calibrating Camera Image”
CONSULT work support
1. On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRA TING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2. On the adjustment screen of each camera, adjust the parameter by touching the “AXIS X” but ton, “AXIS Y” button, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
3. Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
4. Touch “OK” button on the CONSUL T screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
>> GO TO 6.
6.PERFORM “FINE TUNING OF BIRDS-EYE VIEW”
7. Point RR (mark)
A. 75 cm (29.5 in) B. Approx. 1.5 m (59 in)C.30 cm (11.8 in)
[Vehicle width/ 2 + 30 cm (11.8 in)
from the points FM and RM]
JSNIA0922ZZ
1. Point FL
2. Point FR3. Point RL
4. Point RR 5. Center position of axle6. Triangle scale
Adjustment range
Rotation direction (Center dial) : 31 patterns (16 on the center)
Upper/lower direction (upper/lower
switch) :
−22 – 22
Left/right direction (left/right switch) : −22 – 22
JSNIA4212ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-184
< BASIC INSPECTION >[NAVIGATION]
INSPECTION AND ADJUSTMENT
This mode is designed to align the boundary between each camera image that could not be aligned in the
“Calibrating Camera Image” mode.
CONSULT work support
1. Select “FINE TUNING OF BIRDS- EYE VIEW” by touching CONSULT screen.
2. On the adjustment screen of each camera, adjust the parameter by touching the “AXIS X” button, “AXIS Y” button”, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
NOTE:
Touch “SELECT” button on the CONSULT screen to select the
target camera.
3. Touch “APPLY” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are shown on the camera
screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other
operations while “PRCSNG” is displayed.
4. Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
• Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis- played.
• After pressing the “OK” button, never press buttons other than the “BACK” button.
NOTE:
• It can be initialized to the NISSA N factory default condition with “Initialize Camera Image Calibration”.
• The adjustment value is cancelled in this mode by performing “Initialize Camera Image Calibration”.
>> Calibration end
JSNIA4214ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
U0428 STEERING ANGLE SENSORAV-185
< DTC/CIRCUIT DIAGNOSIS > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
DTC/CIRCUIT DIAGNOSIS
U0428 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000012433040
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012433041
1.ADJUST THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
When U0428 is detected, adjust the neutral position of the steering angle sensor.
>> Perform adjustment of the neutral position of the steering angle sensor. Refer to AV-146, "
CON-
SULT Function".
CONSULT Display DTC Detection Condition Possible Cause
ST ANG SEN CALIB
[U0428] The neutral position adjustment of the steering
angle sensor is incomplete. Adjust neutral position of the steering angle sen-
sor.
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-186
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
U1000 CAN COMM CIRCUIT
U1000 CAN COMM CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : DTC LogicINFOID:0000000012433042
DTC DETECTION LOGIC
AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000012433043
1.PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Perform Self Diagnostic Result for MULTI AV.
Is CAN COMM CIRCUIT displayed?
YES >> Refer to LAN-16, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-42, "
Intermittent Incident".
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : DTC LogicINFOID:0000000012433044
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTRO L UNIT : Diagnosis ProcedureINFOID:0000000012433045
1.PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Perform Self Diagnostic Result for AVM.
Is CAN COMM CIRCUIT displayed?
YES >> Refer to LAN-16, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-42, "
Intermittent Incident".
CONSULT Display DTC Detection Condition Possible Cause
CAN COMM CIRCUIT
[U1000] AV control unit is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
CONSULT Display
DTC Detection Condition Possible Cause
CAN COMM CIRCUIT
[U1000] Around view monitor control unit is not transmit-
ting or receiving CAN communication signal for 2
seconds or more.
CAN communication system.
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
U1010 CONTROL UNIT (CAN)AV-187
< DTC/CIRCUIT DIAGNOSIS > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
U1010 CONTROL UNIT (CAN)
AV CONTROL UNIT
AV CONTROL UNIT : DTC LogicINFOID:0000000012433046
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CO NTROL UNIT : DTC LogicINFOID:0000000012433047
DTC DETECTION LOGIC
CONSULT Display DTC Detection Condition Possible Cause
CONTROL UNIT (CAN)
[U1010] Error during CAN controller hardware initializa-
tion (VCAN). Replace the AV control unit if the malfunction oc-
curs constantly.
Refer to AV- 2 4 1 , "
Removal and Installation".
CONSULT Display
DTC Detection Condition Possible Cause
CONTROL UNIT (CAN)
[U1010] Error during CAN controller hardware initializa-
tion (VCAN). Replace the Around view monitor control unit if
the malfunction occurs constantly.
Refer to AV- 2 4 9 , "
Removal and Installation".
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-188
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DTC LogicINFOID:0000000012433048
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012433049
Regarding Wiring Diagram information, refer to
AV-155, "Wiring Diagram".
WITH AROUND VIEW MONITOR
1.CHECK REAR VIEW CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
3. Check continuity between around view monitor control unit connector B54 and rear view camera connec- tor D501.
4. Check continuity between around view m onitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK REAR VIEW CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and rear view camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace around view monitor control unit. Refer to AV-249, "
Removal and Installation".
3.CHECK REAR VIEW CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
CONSULT Display DTC Detection Condition Possible Cause
Rear display output signal diag-
nosis (Harness disconnection)
[ U 111 A ] Rear view camera image signal circuit open or
short.
Check rear view camera image signal circuit.
Around view monitor control unit
Rear view camera
Continuity
Connector TerminalsConnector Terminals
B54 26
D501 2
Ye s
25 1
Around view monitor control unit
GroundContinuity
Connector Terminal
B54 26 No
Around view monitor control unit
GroundCondition Vol tag e
(Approx.)
Connector Terminal
B54 26—CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-192
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
U111B SIDE CAMERA RH
IMAGE SIGNAL CIRCUIT
DTC LogicINFOID:0000000012433050
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012433051
Regarding Wiring Diagram information, refer to AV-155, "Wiring Diagram".
1.CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector B54 and RH side camera connector D107.
4. Check continuity between around view m onitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace around view monitor control unit. Refer to AV-249, "
Removal and Installation".
3.CHECK RH SIDE CAMERA IMAGE SIGNAL A ND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
CONSULT Display DTC Detection Condition Possible Cause
Right side display output signal
diagnosis (Harness disconnec-
tion)
[ U 111 B ] Right side camera image signal circuit open or
short.
Check right side camera image signal circuit.
Around view monitor control unit
RH side camera
Continuity
Connector TerminalsConnector Terminals
B54 34
D107 2
Ye s
33 1
Around view monitor control unit
GroundContinuity
Connector Terminal
B54 34 No
Around view monitor control unit
GroundCondition Vol tag e
(Approx.)
Connector Terminal
B54 34—CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-194
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DTC LogicINFOID:0000000012433052
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012433053
Regarding Wiring Diagram information, refer to
AV-155, "Wiring Diagram".
1.CHECK FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and front camera connectors.
3. Check continuity between around view monitor c ontrol unit connector B54 and front camera connector
E71.
4. Check continuity between around view m onitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK FRONT CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and front camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace around view monitor control unit. Refer to AV-249, "
Removal and Installation".
3.CHECK FRONT CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GRO UND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and front camera connectors.
CONSULT Display DTC Detection Condition Possible Cause
Front display output signal diag-
nosis (Harness disconnection)
[ U 111 C ] Front camera image signal circuit open or short. Check front camera image signal circuit.
Around view monitor control unit
Front camera
Continuity
Connector TerminalsConnector Terminals
B54 38
E71 1
Ye s
37 2
Around view monitor control unit
GroundContinuity
Connector Terminal
B54 38 No
Around view monitor control unit
GroundCondition Vol tag e
(Approx.)
Connector Terminal
B54 38—CAMERA switch is ON or
selector lever in R (re-
verse). 6.0 V
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-196
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC LogicINFOID:0000000012433054
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012433055
Regarding Wiring Diagram information, refer to
AV-155, "Wiring Diagram".
1.CHECK LH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector B54 and LH side camera connector D4.
4. Check continuity between around view m onitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector B54 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace around view monitor control unit. Refer to AV-249, "
Removal and Installation".
3.CHECK LH SIDE CAMERA IMAGE SIGNAL A ND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
CONSULT Display DTC Detection Condition Possible Cause
Left side display output signal
diagnosis (Harness disconnec-
tion)
[ U 111 D ] Left side camera image signal circuit open or
short.
Check left side camera image signal circuit.
Around view monitor control unit
LH side camera
Continuity
Connector TerminalsConnector Terminals
B54 30
D4 2
Ye s
29 1
Around view monitor control unit
GroundContinuity
Connector Terminal
B54 30 No
Around view monitor control unit
GroundCondition Vol tag e
(Approx.)
Connector Terminal
B54 30—CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Revision: August 2015
2016 Versa Note

cardiagn.com