Display NISSAN NOTE 2016 Service Manual Online

AV-144
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
3. While pressing the APPS button, turn the TUNE dial counter-
clockwise 5 or more clicks, then clockwise 5 or more clicks, then
counterclockwise 5 or more clicks. Shifting from current screen
to previous screen is performed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Version, User Configuration, Radio, Syst em State or Self Test can be
selected.
CONSULT FunctionINFOID:0000000012433016
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-151, "DTC Index".
DATA MONITOR
CONFIGURATION
Refer to AV-175, "CONFIGURATION (AV CONTROL UNIT) : Description".
CAN DIAG SUPPORT MNTR
AWNIA3744ZZ
AWNIA3745ZZ
Direct Diagnostic Mode Description
ECU Identification The AV control unit part number is displayed.
Self Diagnostic Result The AV control unit self diagnostic results are displayed.
Data Monitor The AV control unit input/output data is displayed in real time.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr • The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off] Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off] Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off] Indicates condition of ignition signal.
REV SIG [On/Off] Indicates condition of reverse signal received from transmission range switch (with CVT)
or park/neutral position (PNP) switch (back-up) (with M/T).
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-146
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)
DIAGNOSIS SYSTEM (AROUND VI
EW MONITOR CONTROL UNIT)
CONSULT FunctionINFOID:0000000012433017
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the around view monitor control unit.
ECU IDENTIFICATION
The part number of around view monitor control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-154, "DTC Index".
DATA MONITOR
WORK SUPPORT
Direct Diagnostic Mode Description
ECU Identification The around view monitor control unit part number is displayed.
Self Diagnostic Result The around view monitor control unit self diagnostic results are displayed.
Data Monitor The around view monitor control unit input/output data is displayed in real time.
Work support The settings for around view monitor control unit functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing around view monitor control unit.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item Description
ST ANGLE SENSOR SIGNAL [On/Off] Indicates condition of steering angle sensor signal.
REVERSE SIGNAL [On/Off] Indicates selector lever position.
VEHICLE SPEED SIGNAL [mph/km/h] Indicate s condition of vehicle speed signal.
CAMERA SWITCH SIGNAL [On/Off] Indicates condition of camera switch signal.
CAMERA OFF SIGNAL [On/Off] Indicates condition of camera OFF signal.
ST ANGLE SENSOR TYPE [Absolute] Indicates steering angle sensor type.
STEERING GEAR RATIO TYPE [Type
0] Indicates steering gear ratio type.
STEERING POSITION [LHD/RHD] Indi cates LH or RH drive type.
REAR CAMERA IMAGE SIGNAL [OK/
NG] Indicates condition of camera image signal.
F-CAMERA IMAGE SIGNAL [OK/NG] Indicates condition of camera image signal.
DR-SIDE CAMERA IMAGE SIG [OK/
NG] Indicates condition of camera image signal.
PA-SIDE CAMERA IMAGE SIG [OK/
NG] Indicates condition of camera image signal.
Support Item
Setting Description
NON-VIEWABLE AREA REMINDER ON
ON/OFF setting of non-viewable area can be performed.
OFF
PREDICTIVE COURSE LINE
DISPLAY ON
ON/OFF setting of predictive course line display can be performed.
OFF
INITIALIZE CAMERA IMAGE
CALIBRATION — Factory image calibration restoration can be performed.
STEERING ANGLE SENSOR
ADJUSTMENT — Steering angle sensor neutral position adjustment can be performed.
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-150
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AV CONTROL UNIT
28
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
30
(Y) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
31
(G) Ground AUX ground
— ON— 0V
32
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
33
(B) Ground Camera ground
— ON — 0 V
34
(L) Ground Camera power supply Output ON Camera image displayed
6.0 V
Except for above 0 V
35
(Shield) —Camera image signal
shield —— —
—
36
1
(Y)
Ground Camera image signal Input ON When camera image is dis-
played
36
2
(G)
37
(BG) Ground Ignition power supply Input ON
—Battery voltage
42
(L) Ground MIC VCC
Output ON—5 V
43
(P) 41
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
45
(W) — V BUS signal
— —— —
46
(G) — USB ground
— —— —
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB2251J
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
AV CONTROL UNITAV-151
< ECU DIAGNOSIS INFORMATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
1: Without around view monitor
2: With around view monitor
DTC IndexINFOID:0000000012433019
47
(L) — USB D+ signal
— —— —
48
(R) — USB D
− signal — — — —
49
(Shield) — USB shield
— —— —
50
(B) Ground Antenna amp. ON signal Output ON
AV control unit ON, FM-AM
selected.Battery voltage
51
(B) Ground AM-FM main antenna Input ON AV control unit ON, FM-AM
selected.5.0 V
52
(Shield) —AM-FM main antenna
shield
—— —
—
55
(B) Ground GPS antenna signal Input ON
AV control unit ON, NAV se-
lected.5.0 V
56
(Shield) — GPS antenna shield
— —— —
57
(B) Ground Satellite antenna signal Input ON AV control unit ON, XM se-
lected.
5.0 V
58
(Shield) — Satellite antenna shield — —
——
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
CONSULT Display
Reference Page
U1000: CAN COMM CIRCUIT AV-186, "
AV CONTROL UNIT : DTC Logic"
U1010: CONTROL UNIT (CAN)AV-187, "AV CONTROL UNIT : DTC Logic"
U1200: Cont Unit AV- 1 9 8 , "DTC Logic"
U1217: BLUETOOTH MODULEAV- 1 9 9 , "DTC Logic"
U1229: iPod CERTIFICATIONAV- 2 0 0 , "DTC Logic"
U122F: Digital broadcasting connection errorAV- 2 0 1 , "DTC Logic"
U1244: GPS ANTENNA CONNAV- 2 0 3 , "DTC Logic"
U1258: XM ANTENNA CONNAV- 2 0 4 , "DTC Logic"
U1263: USB OVERCURRENTAV- 2 0 5 , "DTC Logic"
U1264: ANTENNA AMP TERMINALAV- 2 0 6 , "DTC Logic"
U12AA: Configuration ErrorAV- 2 0 7 , "DTC Logic"
U12AC: Display Temperature too High AV- 2 0 8 , "DTC Logic"
U12AD: ECU Temperature too High AV- 2 0 9 , "DTC Logic"
U12AE: Internal Amplifier temperature WarningAV- 2 1 0 , "DTC Logic"
U12AF: CD Mechanism Temperature Warning AV- 2 11 , "DTC Logic"
U12B0: Supply Voltage Goes below 9V > 20sAV- 2 1 2 , "DTC Logic"
U12B1: Supply Voltage Goes High > 16V for 20sAV- 2 1 3 , "DTC Logic"
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-154
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AROUND VIEW MONITOR CONTROL UNIT
DTC Index
INFOID:0000000012433021
34
(L) Ground Side camera RH power
supply Output ONCAMERA selected
or
Shift selector in R (reverse)
position. 6.0 V
36
(Y) 35
(Shield) Side camera RH image sig-
nal
Input ONCAMERA selected
or
Shift selector in R (reverse)
position.
37
(B) Ground Front camera ground — ON
—0 V
38
(W) Ground Front camera power supply Output ON CAMERA selected
or
Shift selector in R (reverse)
position.6.0 V
40
(R) 39
(Shield) Front camera image signal Input ON CAMERA selected
or
Shift selector in R (reverse)
position.
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
JSNIA0834GB
JSNIA0834GB
CONSULT Display
Reference Page
U0428: ST ANG SEN CALIB AV-185, "
DTC Logic"
U1000: CAN COMM CIRCUITAV- 1 8 6 , "AROUND VIEW MONITOR CONTROL UNIT :
DTC Logic"
U1010: CONTROL UNIT (CAN)AV- 1 8 7 , "AROUND VIEW MONITOR CONTROL UNIT :
DTC Logic"
U111A: Rear display output signal diagnosis (Harness disconnection)
AV-188, "DTC Logic"
U111B: Right side display output signal diagnosis (Harness disconnection)AV-192, "DTC Logic"
U111C: Front display output signal diagnosis (Harness disconnection)AV-194, "DTC Logic"
U111D: Left side display output signal diagnosis (Harness disconnection)AV-196, "DTC Logic"
U1232: ST ANG SEN CALIBAV-202, "DTC Logic"
U1304: Non-completion of the calibrationAV-214, "DTC Logic"
U1305: Non-completion of the configurationAV-215, "DTC Logic"
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-172
< BASIC INSPECTION >[NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
2. Depending on system being diagnosed, perform Self Diagnostic Result for:
-MULTI AV.
-AVM.
Are any DTCs displayed?
YES >> Refer to AV-151, "DTC Index" (MULTI AV) or
AV-154, "DTC Index" (AVM).
NO >> GO TO 4.
4.PERFORM SYMPTOM DIAGNOSIS
Refer to AV-228, "
Symptom Table".
>> GO TO 5
5.FINAL CHECK
Refer to symptom described by the customer in step 1.
Is the symptom still present?
YES >> GO TO 2
NO >> Inspection End.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
INSPECTION AND ADJUSTMENTAV-173
< BASIC INSPECTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLAC ING AV CONTROL UNIT : Description
INFOID:0000000012433024
BEFORE REPLACEMENT
When replacing AV control unit, save or print current vehicle specification with CONSULT configuration before
replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing AV control unit.
AFTER REPLACEMENT
CAUTION:
When replacing AV control unit, you must perform “After Replace ECU” with CONSULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Re place ECU”, incidents might occur.
• Configuration is different for each vehicle model. Confirm conf iguration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Work Procedure
INFOID:0000000012433025
1.SAVING VEHICLE SPECIFICATION
-CONSULT
Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing AV control unit.
>> GO TO 2.
2.REPLACE AV CONTROL UNIT
Replace AV control unit. Refer to AV-241, "
Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT
1. Enter "Re/Programming, Configuration".
2. If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle
specification. Refer to AV-175, "
CONFIGURATION (AV CONTROL UNIT) : Work Procedure".
3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to AV-175, "
CONFIGURATION (AV CONTROL UNIT) : Work Pro-
cedure".
>> GO TO 4.
4.REGISTER AV CONTROL UNIT
Perform AV control unit registration. Refer to AV-177, "
REGISTRATION (AV CONTROL UNIT) : Work Proce-
dure".
>> GO TO 5.
5.OPERATION CHECK
Check that the operation of the AV control uni t and camera images (fixed guide lines) are normal.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-174
< BASIC INSPECTION >[NAVIGATION]
INSPECTION AND ADJUSTMENT
>> Work End.
ADDITIONAL SERVICE WHEN REPL
ACING AROUND VIEW MONITOR CON-
TROL UNIT
ADDITIONAL SERVICE WHEN REPLAC ING AROUND VIEW MONITOR CONTROL
UNIT : Description
INFOID:0000000012433026
BEFORE REPLACEMENT
When replacing around view monitor control unit, save or print current vehicle specification with CONSULT
configuration before replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing around view monitor control unit.
AFTER REPLACEMENT
CAUTION:
When replacing around view moni tor control unit, you must perform “After Replace ECU” with CON-
SULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Replace ECU”, incidents might occur.
• Configuration is different for each vehicle mode l. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CONTROL
UNIT : Work Procedure
INFOID:0000000012433027
1.SAVING VEHICLE SPECIFICATION
-CONSULT
Enter “Re/Programming, Configuration” and perform “Befor e Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing around view monitor control unit.
>> GO TO 2.
2.REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to AV-249, "
Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT
1. Enter "Re/Programming, Configuration".
2. If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "S aved Data List" and press “Confirm” to write vehicle
specification. Refer to AV-176, "
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work
Procedure".
3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to AV-176, "
CONFIGURATION (AROUND VIEW MONITOR
CONTROL UNIT) : Work Procedure".
>> GO TO 4.
4.OPERATION CHECK
Check that the operation of the around view monito r control unit and camera images (fixed guide lines and
predictive course lines) are normal.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-176
< BASIC INSPECTION >[NAVIGATION]
INSPECTION AND ADJUSTMENT
4.OPERATION CHECK
Confirm that each function controlled by AV control unit operates normally.
>> Work End.
CONFIGURATION (AV CONTROL UNIT) : Configuration ListINFOID:0000000012433030
CAUTION:
Thoroughly read and understand the vehicle specifi cation. Incorrect settings may result in abnormal
control of ECU.
⇔ : Items which confirm vehicle specifications
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Description
INFOID:0000000012433031
Vehicle specification needs to be written with CONSULT because it is not written after replacing around view
monitor control unit.
Configuration has three functions as follows:
CAUTION:
• When replacing around view moni tor control unit, you must perform “Select Saved Data List” or
"After Replace ECU" with CONSULT.
• Complete the procedure of “Select Saved Da ta List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle mode l. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new around view monitor
control unit.
CONFIGURATION (AROUND VI EW MONITOR CONTROL UNIT) : Work Procedure
INFOID:0000000012433032
1.WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of around view monitor control unit.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.PERFORM “SAVED DATA LIST”
CONSULT
Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select
applicable file from the “Save Data List” and press “Confirm”.
>> Work End.
MANUAL SETTING ITEM
Items Setting value
SOUND SYSTEM BASE ⇔ BOSE
CAMERA SYSTEM NONE/AVM ⇔ REAR CAMERA
Function Description
"Before Replace ECU" • Reads the vehicle configuration of current around view monitor control unit.
• Saves the read vehicle configuration.
"After Replace ECU" Writes the vehicle configuration with manual selection.
"Select Saved Data List" Writes the vehicle configuration with saved data.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-180
< BASIC INSPECTION >[NAVIGATION]
INSPECTION AND ADJUSTMENT
View in the incomplete calibration state is indicated by “ ” on the
around view monitor.
CALIBRATION PROCEDURE
1.AROUND VIEW MONITOR SCREEN CONFIRMATION
Check that there is no indication of “Incomplete calibration”.
Is the
“Incomplete calibration” display visible?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK THAT AROUND VIEW MONI TOR CONTROL UNIT IS REPLACED
Check that the around view monitor control unit is replaced.
Is the around view monitor control unit replaced?
YES >> GO TO 3.
NO >> GO TO 5.
3.CANCEL THE INDICATION OF INCO MPLETE CALIBRATION (PERFORM THIS ONLY AFTER REPLAC-
ING AROUND VIEW MONITOR CONTROL UNIT.)
CONSULT work support
1. On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRA TING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2. On the adjustment screen of each camera, touch “APPLY” but-
ton. After this, touch “OK” button.
CAUTION:
• Never perform operations other than those mentionedabove.
• Never perform “Initialize Camera Image Calibration”.
3. Display the around view monitor screen to check that there is no
errors, such as deviations among the camera images.
Is there a malfunction?
YES >> Calibration end
NO >> GO TO 1.
4.PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMEN T BY “FINE TUNING OF BIRDS-EYE VIEW”
1. Put target line 1 on the ground beside each axle using packing tape, etc.
2. Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away fr om the vehicle (make the line as parallel with the
vehicle as possible)
AWNIA2590GB
AWNIA2590GB
JSNIA4212ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com