heater NISSAN NOTE 2016 Service User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 1190 of 3641
![NISSAN NOTE 2016 Service User Guide DIAGNOSIS SYSTEM (ECM)EC-63
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
OLOAD SIGNAL ON/OFF
• Indicates [ON/OFF] condition of the electrical
lode signal.
- ON: Rear window defogge](/img/5/57363/w960_57363-1189.png "NISSAN NOTE 2016 Service User Guide DIAGNOSIS SYSTEM (ECM)EC-63
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
OLOAD SIGNAL ON/OFF
• Indicates [ON/OFF] condition of the electrical
lode signal.
- ON: Rear window defogge")
DIAGNOSIS SYSTEM (ECM)EC-63
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
OLOAD SIGNAL ON/OFF
• Indicates [ON/OFF] condition of the electrical
lode signal.
- ON: Rear window defogger switch is ON and/or lighting switch is 2nd position.
- OFF: Both rear window defogger switch and light-
ing switch are OFF.
IGNITION SW ON/OFFIndicates [ON/OFF] condition from ignition switch
signal.
HEATER FAN SW ON/OFF Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW ON/OFFIndicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1 msecIndicates the actual fuel injection pulse width com-
pensated by ECM according to the input signals. When the engine is stopped, a certain
computed value is indicated.
IGN TIMING BTDCIndicates the ignition timing computed by ECM ac-
cording to the input signals. When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE %“Calculated load value” indicates the value of the
current air flow divided by peak air flow.
MASS AIRFLOW g/sIndicates the mass air flow computed by ECM ac-
cording to the signal voltage of the mass air flow
sensor.
PURG VOL C/V %• Indicates the EVAP canister purge volume con-
trol solenoid valve control value computed by the
ECM according to the input signals.
• The opening becomes larger as the value in-
creases.
INT/V TIM(B1) °CA Indicates [ °CA] of intake camshaft advance angle.
EXH/V TIM B1 °CA Indicates [ °CA] of exhaust camshaft retard angle.
INT/V SOL(B1) %• The control value of the intake valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value increases.
AIR COND RLY ON/OFF The air conditioner relay control condition (deter-
mined by ECM according to the input signals) is in-
dicated.
FUEL PUMP RLY ON/OFF Indicates the fuel pump relay control condition de-
termined by ECM according to the input signals.
VENT CONT/V ON/OFF • The control condition of the EVAP canister vent
control valve (determined by ECM according to
the input signals) is displayed.
- ON: Closed
-OFF: Open
THRTL RELAY ON/OFF Indicates the throttle control motor relay control
condition determined by the ECM according to the
input signals.
COOLING FAN HI/LOW/OFF • Indicates the condition of the cooling fan (deter-
mined by ECM according to the input signals).
- HI: High speed operation
- LOW: Low speed operation
-OFF: Stop
HO2S2 HTR (B1) ON/OFF Indicates [ON/OFF] condition of heated oxygen
sensor 2 heater determined by ECM according to
the input signals.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1191 of 3641
![NISSAN NOTE 2016 Service User Guide EC-64
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
ALT DUTY SIG ON/OFF• The control condition of the power generation
voltage variable control (determined by ECM ac-
cording to the input s](/img/5/57363/w960_57363-1190.png "NISSAN NOTE 2016 Service User Guide EC-64
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
ALT DUTY SIG ON/OFF• The control condition of the power generation
voltage variable control (determined by ECM ac-
cording to the input s")
EC-64
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
ALT DUTY SIG ON/OFF• The control condition of the power generation
voltage variable control (determined by ECM ac-
cording to the input signals) is indicated.
- ON: Power generation voltage variable control is active.
- OFF: Power generation voltage variable control is inactive.
I/P PULLY SPD rpmIndicates the engine speed computed from the in-
put speed sensor signal.
VEHICLE SPEED km/h or mph The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN YET/CMPLT • Displays the condition of Idle Air Volume Learn-
ing.
- YET: Idle air volume learning has not been per-
formed yet.
- CMPLT: Idle air volume learning has already been performed successfully.
TRVL AFTER MIL km or mile Distance traveled while MIL is activated.
ENG OIL TEMP °C or °F The engine oil temperature (determined by the sig-
nal voltage of the engine oil temperature sensor) is
indicated.
A/F S1 HTR(B1) %• Air fuel ratio (A/F) sensor 1 heater control value
computed by ECM according to the input signals.
• The current flow to the heater becomes larger as the value increases.
VHCL SPEED SE km/h or mph The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
SET VHCL SPD km/h or mph The preset vehicle speed is displayed.
MAIN SW ON/OFFIndicates [ON/OFF] condition from ASCD MAIN
switch signal.
CANCEL SW ON/OFFIndicates [ON/OFF] condit
ion from CANCEL switch
signal.
RESUME/ACC SW ON/OFF Indicates [ON/OFF] condition from ACCEL/RES
switch signal.
SET SW ON/OFFIndicates [ON/OFF] condition from COAST/SET
switch signal.
BRAKE SW1 ON/OFFIndicates [ON/OFF] condition from ASCD brake
switch signal.
BRAKE SW2 ON/OFFIndicates [ON/OFF] condition of stop lamp switch
signal.
VHCL SPD CUT NON/CUT • Indicates the vehicle cruise condition.
- NON: Vehicle speed is maintained at the ASCD
set speed.
- CUT: Vehicle speed decreased to excessively
low compared with the ASCD set speed, and
ASCD operation is cut off.
LO SPEED CUT NON/CUT • Indicates the vehicle cruise condition.
- NON: Vehicle speed is maintained at the ASCD
set speed.
- CUT: Vehicle speed decreased to excessively low, and ASCD operation is cut off.
AT OD MONITOR ON/OFF Indicates [ON/OFF] condition of CVT O/D accord-
ing to the input signal from the TCM.
AT OD CANCEL ON/OFF Indicates [ON/OFF] condition of CVT O/D cancel
request signal.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1199 of 3641
![NISSAN NOTE 2016 Service User Guide EC-72
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
EVAP SYS PRES • Ignition switch: ON
Approx. 1.8 - 4.8 V
FUEL LEVEL SE • Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL • I](/img/5/57363/w960_57363-1198.png "NISSAN NOTE 2016 Service User Guide EC-72
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
EVAP SYS PRES • Ignition switch: ON
Approx. 1.8 - 4.8 V
FUEL LEVEL SE • Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL • I")
EC-72
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
EVAP SYS PRES • Ignition switch: ON
Approx. 1.8 - 4.8 V
FUEL LEVEL SE • Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL • Ignition switch: ON → START → ON OFF → ON → OFF
CLSD THL POS • Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released
ON
Accelerator pedal: Slightly depressed OFF
AIR COND SIG • Engine: After warming up, idle
the engine Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates.) ON
PW/ST SIGNAL • Engine: After warming up, idle
the engine Steering wheel: Not being turned
OFF
Steering wheel: Being turned ON
LOAD SIGNAL • Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF OFF
IGNITION SW • Ignition switch: ON → OFF → ON ON → OFF → ON
HEATER FAN SW • Engine: After warming up, idle
the engine Heater fan switch: ON
ON
Heater fan switch: OFF OFF
BRAKE SW • Ignition switch: ON Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed ON
INJ PULSE-B1 • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
IGN TIMING • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
4
°BTDC (CVT)
10 °BTDC (M/T)
2,000 rpm 25° - 45 °BTDC
CAL/LD VALUE • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
10% - 35%
2,500 rpm 10% - 35%
MASS AIRFLOW • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
0.8 - 4.0 g/s
2,500 rpm 2.0 - 10.0 g/s
PURG VOL C/V • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idl
e
0%
2 ,
000 rpm
0% - 50%
INT/V TIM(B1) • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
−5° - 5 °CA
When revving engine up to 2,000rpm
Quickly Approx. 0
° - 40 °CA
Monitor Item
Condition Values/Status
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1203 of 3641
![NISSAN NOTE 2016 Service User Guide EC-76
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
*: Accelerator pedal position sensor 2 signal and throttle
position sensor 2 signal are converted by ECM inter-
nally. Thus, they differ from ECM termi](/img/5/57363/w960_57363-1202.png "NISSAN NOTE 2016 Service User Guide EC-76
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
*: Accelerator pedal position sensor 2 signal and throttle
position sensor 2 signal are converted by ECM inter-
nally. Thus, they differ from ECM termi")
EC-76
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
*: Accelerator pedal position sensor 2 signal and throttle
position sensor 2 signal are converted by ECM inter-
nally. Thus, they differ from ECM terminals voltage signal.
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
• Connect a break-out box and harness adapter between the ECM and ECM harness connector.
- Use extreme care not to touch 2 pins at one time.
- Data is for comparison and may not be exact.
• Specification data are reference values and are measured between each terminals.
• Pulse signal is measured by CONSULT.
A/F IMBLNC DIAG-
CPS CMPLT Self-diagnosis of DTC P219C – P219F is incomplete.
INCMP
Self-diagnosis of DTC P219C – P219F is complete. CMPLT
Monitor Item
Condition Values/Status
PBIA9221J
Terminal No.Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
1
(L) 108
(B) Throttle control motor
(Open)
Output[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully de-
pressed 2.6 V
2
(L/W) 108
(B) Throttle control motor power
supply
Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
3
(G/W) 108
(B) A/F sensor 1 heater Output [Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine) 2.9 - 8.8 V
4
(P) 108
(B) Throttle control motor
(Close)
Output[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released 1.8 V
JMBIA0213GB
JSBIA0714GB
JMBIA0215GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1204 of 3641
![NISSAN NOTE 2016 Service User Guide ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the](/img/5/57363/w960_57363-1203.png "NISSAN NOTE 2016 Service User Guide ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the")
ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the following conditions are
met
- Engine: after warming up
- Keeping the engine speed be- tween 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
9
(SB) 108
(B) EVAP canister purge vol-
ume control solenoid valve
Output[Engine is running]
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Engine speed: About 2,000 rpm (More than 100 seconds after
starting engine.) BATTERY VOLTAGE
(11 - 14 V)
10
(B) — ECM ground — — —
11
(B/Y) — ECM ground
—— —
12
(L/W)
108(B) Fuel injector No. 1 (Rear)
Output[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
16
(G) Fuel injector No. 3 (Rear)
20
(O/W) Fuel injector No. 2 (Rear)
24
(R) Fuel injector No. 4 (Rear)
25
(R) Fuel injector No. 4 (Front)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpmBATTERY VOLTAGE
(11 - 14 V)
29
(G) Fuel injector No. 3 (Front)
30
(O) Fuel injector No. 2 (Front)
31
(L) Fuel injector No. 1 (Front)
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA0214GB
JMBIA0039GB
JMBIA0216GB
JMBIA0221GB
JMBIA0222GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1213 of 3641
![NISSAN NOTE 2016 Service User Guide EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P01](/img/5/57363/w960_57363-1212.png "NISSAN NOTE 2016 Service User Guide EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P01")
EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P0101 P0102 P0103 Mass air flow sensor
• P0111 P0112 P0113 P0127 Intake air temperature sensor
• P0116 P0117 P0118 P0125 Engine coolant temperature sensor
• P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
• P0128 Thermostat function
• P0181 P0182 P0183 Fuel tank temperature sensor
• P0196 P0197 P0198 Engine oil temperature sensor
• P0327 P0328 Knock sensor
• P0335 Crankshaft position sensor (POS)
• P0340 Camshaft position sensor (PHASE)
• P0500 Vehicle speed sensor
• P0520 Engine oil pressure sensor
• P0603 P0604 P0605 P0606 P0607 P060A P060B ECM
• P0643 Sensor power supply
• P0850 Park/neutral position (PNP) switch
• P1550 P1551 P1552 P1553 P1554 Battery current sensor
• P1610 - P1615 NATS
• P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
2 • P0030 P0031 P0032 Air fuel ratio (A/F) sensor 1 heater • P0037 P0038 Heated oxygen sensor 2 heater
• P0075 Intake valve timing control solenoid valve
• P0078 Exhaust valve timing control solenoid valve
• P0130 P0131 P0132 P0133 P014C P014D P015A P015B P2096 P2097 Air fuel ratio (A/F) sensor 1
• P0137 P0138 P0139 Heated oxygen sensor 2
• P0441 EVAP control system purge flow monitoring
• P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
• P0447 P0448 EVAP canister vent control valve
• P0451 P0452 P0453 EVAP control system pressure sensor
• P0460 P0461 P0462 P0463 Fuel level sensor
• P059F Active grille shutter
• P1078 Exhaust valve timing control position sensor
• P1217 Engine over temperature (OVERHEAT)
• P1805 Brake switch
• P2100 P2103 Throttle control motor relay
• P2101 Electric throttle control function
• P2118 Throttle control motor
3 • P0011 Intake valve timing control • P0014 Exhaust valve timing control
• P0171 P0172 Fuel injection system function
• P0300 - P0304 Misfire
• P0420 Three way catalyst function
• P0456 EVAP control system (VERY SMALL LEAK)
• P0506 P0507 Idle speed control system
• P050A P050B P050E Cold start control
• P0524 Engine oil pressure
• P1148 Closed loop control
• P1212 TCS communication line
• P1564 ASCD steering switch
• P1572 ASCD brake switch
• P1574 ASCD vehicle speed sensor
• P1715 Input speed sensor
• P1720 Vehicle speed sensor
• P2119 Electric throttle control actuator
• P219A P219C P219D P219E P219F Air fuel ratio (A/F) sensor 1
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1222 of 3641
![NISSAN NOTE 2016 Service User Guide ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
O2 SEN-
SOR
HEATER 41H A/F sensor 1 heater (Bank 1)
Low Input: P0031
High Input: P0032 81H 0BHConverted value of heate](/img/5/57363/w960_57363-1221.png "NISSAN NOTE 2016 Service User Guide ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
O2 SEN-
SOR
HEATER 41H A/F sensor 1 heater (Bank 1)
Low Input: P0031
High Input: P0032 81H 0BHConverted value of heate")
ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
O2 SEN-
SOR
HEATER 41H A/F sensor 1 heater (Bank 1)
Low Input: P0031
High Input: P0032 81H 0BHConverted value of heater electric cur-
rent to voltage
P0030 83H 0BH A/F sensor heater circuit malfunction
42H Heated oxygen sensor 2 heat-
er (Bank 1) Low Input: P0037
High Input: P0038 80H 0CH
Converted value of heater electric cur-
rent to voltage
P0141 81H 14H Rear O2 sensor internal impedance
43H Heated oxygen sensor 3 heat-
er (Bank 1) P0043 80H 0CHConverted value of heater electric cur-
rent to voltage
45H A/F sensor 1 heater (Bank 2) Low Input: P0051
High Input: P0052 81H 0BHConverted value of heater electric cur-
rent to voltage
P0036 83H 0BH A/F sensor heater circuit malfunction
46H Heated oxygen sensor 2 heat-
er (Bank 2) Low Input: P0057
High Input: P0058 80H 0CH
Converted value of heater electric cur-
rent to voltage
P0161 81H 14CH Rear O2 sensor internal impedance
47H Heated oxygen sensor 3 heat-
er (Bank 2) P0063 80H 0CHConverted value of heater electric cur-
rent to voltage
SEC-
OND-
ARY AIR 71H Secondary air system P0411 80H 01H
Secondary air injection system incor-
rect flow detected
Bank1: P0491
Bank2: P0492 81H 01H
Secondary air injection system insuffi-
cient flow
P2445 82H 01H Secondary air injection system pump
stuck off
P2448 83H 01H Secondary air injection system high
airflow
Bank1: P2440
Bank2: P2442 84H 01H
Secondary air injection system switch-
ing valve stuck open
P2440 85H 01H Secondary air injection system switch-
ing valve stuck open
P2444 86H 01H Secondary air injection system pump
stuck on
Item
OBD-
MID Self-diagnostic test item
DTCTest value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1301 of 3641
![NISSAN NOTE 2016 Service User Guide EC-174
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
P0030, P0031, P0032 A/F SENSOR HEATER
DTC LogicINFOID:0000000012723407
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.](/img/5/57363/w960_57363-1300.png "NISSAN NOTE 2016 Service User Guide EC-174
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
P0030, P0031, P0032 A/F SENSOR HEATER
DTC LogicINFOID:0000000012723407
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.")
EC-174
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
P0030, P0031, P0032 A/F SENSOR HEATER
DTC LogicINFOID:0000000012723407
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm th at battery voltage is more than between 11 V at
idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-174, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012723408
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2. Turn ignition switch ON.
3. Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
DTC No. Trouble diagnosis name
(Trouble diagnosis con-
tent) DTC detecting condition Possible cause
P0030 A/F SEN 1 HTR (B1)
(Air fuel ratio (A/F) sensor
1 heater control circuit) Deterioration in A/F sensor 1 heater performance.
(Voltage signal transmitted from A/F sensor 1 heat-
er to ECM is higher/lower than voltage in the nor-
mal range.)
• Harness or connectors
(A/F sensor 1 heater circuit is open or
shorted.)
• A/F sensor 1 heater
P0031 A/F SEN 1 HTR (B1)
(Air fuel ratio (A/F) sensor
1 heater control circuit low) The current amperage in the A/F sensor 1 heater
circuit is out of the normal range.
(An excessively low voltage signal is sent to ECM
through the A/F sensor 1 heater.)
P0032 A/F SEN 1 HTR (B1)
(Air fuel ratio (A/F) sensor
1 heater control circuit
high) The current amperage in the A/F sensor 1 heater
circuit is out of the normal range.
(An excessively high voltage signal is sent to ECM
through the A/F sensor 1 heater.) • Harness or connectors
(A/F sensor 1 heater circuit is short-
ed.)
• A/F sensor 1 heater
+
−Voltag e
A/F sensor 1
Connector Terminal F12 4Ground Battery voltage
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1302 of 3641
![NISSAN NOTE 2016 Service User Guide P0030, P0031, P0032 A/F SENSOR HEATER
EC-175
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
2.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Discon](/img/5/57363/w960_57363-1301.png "NISSAN NOTE 2016 Service User Guide P0030, P0031, P0032 A/F SENSOR HEATER
EC-175
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
2.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Discon")
P0030, P0031, P0032 A/F SENSOR HEATER
EC-175
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
2.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
3.CHECK A/F SENSOR 1 HEATER
Check the A/F sensor 1 heater. Refer to EC-175, "
Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 4.
4.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ra tio (A/F) sensor 1. Refer to EM-31, "
Exploded View".
CAUTION:
• Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F senso r, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize Lubricant
(commercial service tool).
>> INSPECTION END
Component InspectionINFOID:0000000012723409
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect A/F sensor 1 harness connector.
3. Check resistance between A/F sensor 1 terminals as per the following.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-31, "
Exploded View".
CAUTION:
+ −
Continuity
A/F sensor 1 ECM
Connector Terminal Connector Terminal F12 3F10 3 Existed
+ −
Resistance
A/F sensor 1
Te r m i n a l
3 41
.8 - 2 .4 4 Ω [at 25 °C (77 °F)]
1
∞ Ω
(Continuity should not exist)
2
4 1
2
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1303 of 3641
![NISSAN NOTE 2016 Service User Guide EC-176
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a c](/img/5/57363/w960_57363-1302.png "NISSAN NOTE 2016 Service User Guide EC-176
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a c")
EC-176
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0030, P0031, P0032
A/F SENSOR HEATER
• Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads usi ng Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2015 2016 Versa Note
cardiagn.com