tow NISSAN NOTE 2016 Service User Guide

B RC-106
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1154 TRANSMISSION RANGE SWITCH
C1154 TRANSMISSION RANGE SWITCH
DTC DescriptionINFOID:0000000012430885
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1154” detected?
YES-1 >> “C1154” is displayed as “CRNT”: Proceed to BRC-106, "Diagnosis Procedure".
YES-2 >> “C1154” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430886
CAUTION:
“C1154” may be detected when goin g up a slope, being towed with ignition switch ON and the shift
selector in a position other than R position. This is not a shift position error. The system returns to
normal once the vehicle is stopped, parked on level ground and the engine is started.
1.CHECK CVT SYSTEM
With CONSULT
Perform “Self Diagnostic Resu lt” of “TRANSMISSION”.
Is DTC detected?
YES >> Check the DTC. Refer to TM-110, "DTC Index".
NO >> GO TO 2.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1154 PNP POSI SIG
(PNP position signal) When a malfunction is detected in TCM system.
PAST DTC
CRNT DTC
• Harness or connector
• Transmission range switch • Harness or connector
• ABS actuator and electric unit (control unit)
•TCM
• Transmission range switch
Revision: August 2015
2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-171
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
7. While pulling outside handle (1), slide toward rear of vehicle.
8. Disconnect the harness connectors from the outside handle and remove.
9. Remove front gasket and rear gasket.
10. Slide outside handle bracket toward rear of vehicle to remove. : Front
11. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-174
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are pr operly engaged to inside handle.
• After installation, check door op en/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430130
REMOVAL
1. Remove inside handle. Refer to DLK-173, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR DOOR LOCKDLK-175
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
5. Remove front gasket and rear gasket.
6. Slide outside handle bracket toward rear of vehicle to remove. : Front
7. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close, lock/un lock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-298
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
7. While pulling outside handle (1), slide toward rear of vehicle to
remove.
8. Remove front gasket and rear gasket.
9. Slide outside handle bracket toward rear of vehicle to remove. : Front
10. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are prope rly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR DOOR LOCKDLK-301
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
6. Release inside handle cable (3) and lock cable (2) from inside handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/un lock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430276
REMOVAL
1. Remove inside handle. Refer to DLK-300, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-302
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
5. Remove front gasket and rear gasket.
6. Slide outside handle bracket toward rear of vehicle to remove.
: Front
7. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door op en/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-54
< REMOVAL AND INSTALLATION >[HR16DE]
TIMING CHAIN
b. Cut liquid gasket by prying the position ( ) as shown, and then
remove the front cover.
12. Remove front oil seal from front cover using a suitable tool. CAUTION:
Be careful not to damage the front cover.
13. Remove chain tensioner (1):
a. Fully push down the chain tensioner lever (A), and then push the plunger (C) into the inside of tensioner.
• The tab (B) is released by fully pushing the lever down. Thenthe plunger can be moved.
b. Pull up the lever to align its hole position with the body hole posi- tion.
• When the lever hole is aligned with the body hole position, theplunger is secured.
• When the protrusion parts of the plunger ratchet and the tab face each other, both hole positions are not aligned. At that
time, correctly engage them and align these hole positions by
slightly moving the plunger.
c. Insert the stopper pin (D) into the body hole through the lever hole, and then secure the lever at the upper position.
NOTE:
A hexagonal wrench of 2.5 mm (0.098 in) is used as a stopper pin (D).
d. Remove chain tensioner.
14. Remove the timing chain tension guide (2) and the timing chain slack guide (1).
15. Remove the timing chain (2). • Pull the timing chain slack toward the camshaft sprocket
(EXH) (1), and then remove the timing chain and start the
removal from camshaft sprocket (EXH) side.
CAUTION:
Do not rotate crankshaft or camshaft while timing chain is
removed. It causes interferen ce between valve and piston.
16. Remove the crankshaft sprocket and the oil pump drive:
JPBIA4140ZZ
PBIC3713E
JPBIA4141ZZ
JPBIA4142ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-56
< REMOVAL AND INSTALLATION >[HR16DE]
TIMING CHAIN
a. Install the crankshaft sprocket (1), the oil pump drive chain (2),
and the oil pump sprocket (3) at the same time.
• Install the crankshaft sprocket so that its invalid gear area (A)is toward the back of the engine.
• Install the oil pump sprocket so that its protrusion faces the front of engine.
NOTE:
There is no matching mark in the oil pump drive related parts.
b. Hold the top of the oil pump shaft using the socket (size: E8), and then tighten the oil pump sprocket nut.
c. Install oil pump drive chain tensioner (1). • Insert the body into the shaft (B) while inserting the spring intothe attaching hole (A) of cylinder block front surface.
• Check that the tension is applied to the oil pump drive chain
after installing.
2. Install timing chain:
• Install by aligning matching marks on each sprocket and tim-ing chain.
• If these matching marks are not aligned, rotate the camshaft
slightly to correct the position.
CAUTION:
• After the matching marks are aligned, keep them aligned by holding them.
• To avoid skipped teeth, do not rotate crankshaft and cam- shaft until front cover is installed.
: Engine front
JPBIA5248ZZ
(1) : Crankshaft sprocket
(2) : Oil pump drive chain
(3) : Oil pump sprocket
JPBIA4230ZZ
JPBIA4143ZZ
(A) : Matching mark (Peripheral groove)
(B) : Pink link
(C) : Matching mark (Peripheral groove)
(D) : Orange link
(E) : Matching mark (stamp)
(F) : Crankshaft key (point straight up)
JPBIA4144ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER BLOCKEM-97
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
3. Install oil jets.
4. Install main bearings and thrust bearings:
a. Remove dust, dirt, and engine oil on the bear
ing mating surfaces of cylinder block.
b. Install thrust bearings to the both sides of the No. 3 journal hous- ing (B) on cylinder block.
• Install thrust bearings with the oil groove (A) facing crankshaftarm (outside).
c. Install the main bearings paying attention to the direction. • Before installing main bearings, apply new engine oil to the bearing surface (inside). Do not apply
engine oil to the back surface, but thoroughly clean it.
• When installing, align main bearing to the center position of cylinder block and main bearing cap.
• Ensure the oil holes on cylinder block and oil holes (A) on the
main bearings (1) are aligned.
NOTE:
For assembly, the center position can be visually identified.
• To install the main bearing, obtain a proper fit. Do not allow the main bearing to lie off the cylinder block chamfer.
• To install the main bearing, obtain a proper fit. Do not allow the
main bearing to lie off bearing cap chamfer.
5. Install signal plate to crankshaft if removed.
a. Set the signal plate (1) with the flange facing toward the counter- weight side (engine front side) to the crankshaft rear surface.
b. After positioning crankshaft and signal plate with positioning dowel pin, tighten bolt.
NOTE:
Dowel pin of crankshaft and signal plate is provided as a set for
each.
c. Remove dowel pin. CAUTION:
Be sure to remove dowel pin.
6. Install crankshaft to cylinder block. • While turning crankshaft by hand, check that it turns smoothly.
CAUTION:
Do not install rear oil seal at this time.
7. Install main bearing caps.
: Engine front
PBIC3258J
PBIC3746E
(A) : Dowel pin hole
JPBIA4231ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com