battery NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 1204 of 3641
![NISSAN NOTE 2016 Service Repair Manual ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the](/img/5/57363/w960_57363-1203.png "NISSAN NOTE 2016 Service Repair Manual ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the")
ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the following conditions are
met
- Engine: after warming up
- Keeping the engine speed be- tween 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
9
(SB) 108
(B) EVAP canister purge vol-
ume control solenoid valve
Output[Engine is running]
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Engine speed: About 2,000 rpm (More than 100 seconds after
starting engine.) BATTERY VOLTAGE
(11 - 14 V)
10
(B) — ECM ground — — —
11
(B/Y) — ECM ground
—— —
12
(L/W)
108(B) Fuel injector No. 1 (Rear)
Output[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
16
(G) Fuel injector No. 3 (Rear)
20
(O/W) Fuel injector No. 2 (Rear)
24
(R) Fuel injector No. 4 (Rear)
25
(R) Fuel injector No. 4 (Front)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpmBATTERY VOLTAGE
(11 - 14 V)
29
(G) Fuel injector No. 3 (Front)
30
(O) Fuel injector No. 2 (Front)
31
(L) Fuel injector No. 1 (Front)
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA0214GB
JMBIA0039GB
JMBIA0216GB
JMBIA0221GB
JMBIA0222GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1205 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-78
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
15
(G/W) 108
(B) Throttle control motor relay Output [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
17
(V)
108(B) I](/img/5/57363/w960_57363-1204.png "NISSAN NOTE 2016 Service Repair Manual EC-78
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
15
(G/W) 108
(B) Throttle control motor relay Output [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
17
(V)
108(B) I")
EC-78
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
15
(G/W) 108
(B) Throttle control motor relay Output [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
17
(V)
108(B) Ignition signal No. 1
Output[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 0 - 0.3 V
18
(Y/B) Ignition signal No. 2
21
(W) Ignition signal No. 4
[Engine is running]
• Warm-up condition
• Engine speed: 2,500 rpm0.2 - 0.5 V
22
(BR) Ignition signal No. 3
23
(GR) 108
(B) Fuel pump relay
Output[Ignition switch: ON]
• For 1 second after turning ignition
switch ON
[Engine is running] 0 - 1.0 V
[Ignition switch: ON]
• More than 1 second after turning ignition switch ON BATTERY VOLTAGE
(11 - 14 V)
26
(P) 108
(B) EVAP canister vent control
valve
Output [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
32
(P) 108
(B) ECM relay
(Self shut-off)
Output[Engine is running]
[Ignition switch: OFF]
• A few seconds after turning igni-
tion switch OFF 0 - 1.0 V
[Ignition switch: OFF]
• More than a few seconds after turning ignition switch OFF BATTERY VOLTAGE
(11 - 14 V)
33
(W) 36
(R) Throttle position sensor 1 Input [Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released
More than 0.36 V
[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully de- pressed Less than 4.75 V
34
(B) 36
(R) Throttle position sensor 2 Input [Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released
Less than 4.75 V
[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Acce
l
erator pedal: Fully de-
pressed More than 0.36 V
36
(R) —Sensor ground
(Throttle position sensor) ——
—
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA0219GB
JMBIA0220GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1206 of 3641
![NISSAN NOTE 2016 Service Repair Manual ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O37
(W) 40
(L) Knock sensor
Input[Engine is running]
• Idle speed
2.5 V
38
(LG/B) 44
(P) Engine coolant temperature
se](/img/5/57363/w960_57363-1205.png "NISSAN NOTE 2016 Service Repair Manual ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O37
(W) 40
(L) Knock sensor
Input[Engine is running]
• Idle speed
2.5 V
38
(LG/B) 44
(P) Engine coolant temperature
se")
ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O37
(W) 40
(L) Knock sensor
Input[Engine is running]
• Idle speed
2.5 V
38
(LG/B) 44
(P) Engine coolant temperature
sensor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
39
(L) 68
(R) Battery temperature sensor Input [Engine is running]
• Battery temperature: 25
°C ( °F)
• Idle speed 3.5 V
40
(L) —Sensor ground
(Knock sensor shield circuit) ——
—
42
(L) 51
(P) Fuel tank temperature sen-
sor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel
tank temperature.
43
(SB) 68
(R) EVAP control system pres-
sure sensor
Input [Ignition switch: ON]
0.5 - 4.6 V
44
(P) —Sensor ground
(Engine coolant tempera-
ture sensor) ——
—
45
(G/B) 52
(LG) Mass air flow sensor
Input[Ignition switch ON]
• Engine stopped
0.4 V
[Engine is running]
• Warm-up condition
• Idle speed 0.8 - 1.3 V
[Engine is running]
• Warm-up condition
• Engine is revving from idle to about 4,000 rpm 0.8 - 1.3 to 2.4 V
(Check for linear voltage rise in
response to engine being in-
creased to about 4,000 rpm.)
46
(V) 55
(G/L) Intake air temperature sen-
sor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with intake
air temperature.
47
(Y) 60
(L) Engine oil pressure sensor Input [Engine is running]
• Warm-up condition
• Idle speed
1.0 - 2.0 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 1.5 - 3.5 V
48
(W/R) 63
(W) Ex
haus
t v
alve timing control
position sensor Input[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 4.3 V
[Engine is running]
• Engine speed: 2,000 rpm 4.3 V
49
(G) 108
(B) A/F sensor 1
Input [Ignition switch: ON] 2.2 V
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JSBIA0716GB
JSBIA0717GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1207 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-80
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
50
(L/R) 59
(L/Y) Heated oxygen sensor 2 Input [Engine is running]
• Revving engine from idle to 3,000
rpm quickly after the following
conditions ar](/img/5/57363/w960_57363-1206.png "NISSAN NOTE 2016 Service Repair Manual EC-80
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
50
(L/R) 59
(L/Y) Heated oxygen sensor 2 Input [Engine is running]
• Revving engine from idle to 3,000
rpm quickly after the following
conditions ar")
EC-80
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
50
(L/R) 59
(L/Y) Heated oxygen sensor 2 Input [Engine is running]
• Revving engine from idle to 3,000
rpm quickly after the following
conditions are met
- Engine: after warming up
- Keeping the engine speed be- tween 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load 0 - 1.0 V
51
(P) —Sensor ground
(Fuel tank temperature sen-
sor) ——
—
52
(LG) —
Sensor ground
(Mass air flow sensor) ——
—
53
(L) 108
(B) A/F sensor 1
Input[Engine is running]
• Warm-up condition
• Engine speed: 2,500 rpm 1.8 V
Output voltage varies with air fuel
ratio.
54
(BR) —Sensor ground
(Engine oil temperature
sensor)
——
—
55
(G/L) —Sensor ground
(Intake air temperature sen-
sor) ——
—
57
(P) 54
(BR) Engine oil temperature sen-
sor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
58
(BR) 68
(R) Battery current sensor Input [Engine is running]
• Battery: Fully charged*
• Idle speed
2.6 - 3.5 V
59
(L/Y) —Sensor ground
(Heated oxygen sensor 2)
——
—
60
(L) —
Sensor ground
(Engine oil pressure sensor) ——
—
61
(L/O) 62
(G) Crankshaft position sensor Input [Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 4.0 V
[Engine is running]
• Engine speed: 2,000 rpm 4.0 V
62
(G) —Sensor ground
(Crankshaft position sensor)
——
—
63
(W) —Se
nsor gro
u
nd
(Camshaft position sensor) ——
—
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA2185GB
JMBIA2186GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1208 of 3641
![NISSAN NOTE 2016 Service Repair Manual ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
65
(R/W) 63
(W) Camshaft position sensor Input [Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse](/img/5/57363/w960_57363-1207.png "NISSAN NOTE 2016 Service Repair Manual ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
65
(R/W) 63
(W) Camshaft position sensor Input [Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse")
ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
65
(R/W) 63
(W) Camshaft position sensor Input [Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 4.3 V
[Engine is running]
• Engine speed is 2,000 rpm 4.3 V
68
(R) —Sensor ground
(EVAP control system pres-
sure sensor, battery current
sensor, battery temperature
sensor) ——
—
69
(BR) 108
(B) Park/Neutral position signal Input [Ignition switch: ON]
• Shift lever: Neutral
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON]
• Shift lever: Except above position 0 V
70
(L/Y) — Engine communication line
Input/
Output ——
71
(Y) 68
(R) Sensor power supply
(EVAP control system pres-
sure sensor, battery current
sensor, battery temperature
sensor)
— [Ignition switch: ON]
5 V
72
(G) 36
(R) Sensor power supply
(Throttle position sensor)
— [Ignition switch: ON]
5 V
73
(P) 108
(B) Intake valve timing control
solenoid valve
Output[Engine is running]
• Warm-up condition
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• When revving engine up to 2,000rpm quickly 7 - 10 V
74
(O) 60
(L) Sensor power supply
(Engine oil pressure sensor)
— [Ignition switch: ON]
5 V
75
(O) 62
(G) Sensor power supply
(Crankshaft position sensor)
— [Ignition switch: ON]
5 V
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
OutputJSBIA0718GB
JSBIA0719GB
JSBIA0720GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1209 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-82
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
77
(P/W) 108
(B) Exhaust valve timing control
solenoid valve
Output[Engine is running]
• Warm-up condition
• Idle speed
BATTERY VOLTAGE
(11 - 14 V](/img/5/57363/w960_57363-1208.png "NISSAN NOTE 2016 Service Repair Manual EC-82
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
77
(P/W) 108
(B) Exhaust valve timing control
solenoid valve
Output[Engine is running]
• Warm-up condition
• Idle speed
BATTERY VOLTAGE
(11 - 14 V")
EC-82
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
77
(P/W) 108
(B) Exhaust valve timing control
solenoid valve
Output[Engine is running]
• Warm-up condition
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• When revving engine up to 2,000rpm quickly 7 - 10 V
78
(BR) 63
(W) Sensor power supply
(Camshaft position sensor)
— [Ignition switch: ON]
5 V
81
(V) 108
(B) Power supply for ECM
(Back-up)
Input [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
83
(P) —CAN-L Input/
Output ——
84
(L) —CAN-H Input/
Output ——
85
(V) 98
(LG) Refrigerant pressure sensor Input [Engine is running]
• Warm-up condition
• Both A/C switch and blower fan
switch: ON (Compressor oper-
ates) 1.0 - 4.0 V
88
(GR) — Data link connector
Input/
Output ——
92
(R) — Clutch pedal position switch Input [Ignition switch: ON]
• Clutch pedal: Fully released
0 V
[Ignition switch: ON]
• Clutch pedal: Fully depressed BATTERY VOLTAGE
(11 - 14 V)
93
(L) 108
(B) Ignition switch
Input[Ignition switch: OFF]
0 V
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
94
(Y) 95
(B) ASCD steering switch Input [Ignition switch: ON]
• ASCD steering switch: OFF
4 V
[Ignition switch: ON]
• MAIN switch: Pressed 0 V
[Ignition switch: ON]
• CANCEL switch: Pressed 1 V
[Ignition switch: ON]
• ACCEL/RES switch: Pressed 3 V
[Ignition switch: ON]
• COAST/SET switch: Pressed 2 V
95
(B) —
Sensor ground
(AS
CD steering
switch) ——
—
98
(LG) —Se
nsor ground
(Refrigerant pressure sen-
sor) ——
—
99
(LG) 108
(B) Stop lamp switch
Input[Ignition switch: OFF]
• Brake pedal: Fully released
0 V
[Ignition switch: OFF]
• Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14 V)
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JSBIA0720GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1210 of 3641
![NISSAN NOTE 2016 Service Repair Manual ECM
EC-83
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*: Before measuring the term](/img/5/57363/w960_57363-1209.png "NISSAN NOTE 2016 Service Repair Manual ECM
EC-83
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*: Before measuring the term")
ECM
EC-83
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*: Before measuring the terminal voltage, confi rm that the battery is fully charged. Refer to PG-61, "
Work
Flow".
Fail SafeINFOID:0000000012431343
100
(G) 108
(B) Brake pedal position switch Input [Ignition switch: OFF]
• Brake pedal: Fully released
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: OFF]
• Brake pedal: Slightly depressed 0 V
101 (W) 98
(LG) Sensor power supply
(Refrigerant pressure sen-
sor)
— [Ignition switch: ON]
5 V
102
(BR) 104
(Y) Sensor power supply
(Accelerator pedal position
sensor 2)
— [Ignition switch: ON]
5 V
103
(GR) 104
(Y) Accelerator pedal position
sensor 2
Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released
0.3 - 0.6 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de- pressed 1.95 - 2.4 V
104 (Y) —Sensor ground
(Accelerator pedal position
sensor 2) ——
—
105 (G) 108
(B) Power supply for ECM Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
106 (V) 111
(P) Sensor power supply
(Accelerator pedal position
sensor 1)
— [Ignition switch: ON]
5 V
108 (B) — ECM ground
—— —
11 0
(SB) 111
(P) Accelerator pedal position
sensor 1
Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released
0.6 - 0.9 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de- pressed 3.9 - 4.7 V
111 (P) —Sensor ground
(Accelerator pedal position
sensor 1) ——
—
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
DTC No. Detected items Engine operating condition in fail safe mode
U0101 CAN communication line ECM operates active grille shutter to fully-open position.
U0284 Active grille shutter ECM operates active grille shutter to fully-open position.
U1040
U1044 Engine communication line ECM operates active grille shutter to fully-open position.
P0011 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve control does not function.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1213 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P01](/img/5/57363/w960_57363-1212.png "NISSAN NOTE 2016 Service Repair Manual EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P01")
EC-86
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
Priority
Detected items (DTC)
1 • U0101 U1001 CAN communication line • U0284 Active grille shutter
• U1040 U1044 Engine communication line
• P0101 P0102 P0103 Mass air flow sensor
• P0111 P0112 P0113 P0127 Intake air temperature sensor
• P0116 P0117 P0118 P0125 Engine coolant temperature sensor
• P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
• P0128 Thermostat function
• P0181 P0182 P0183 Fuel tank temperature sensor
• P0196 P0197 P0198 Engine oil temperature sensor
• P0327 P0328 Knock sensor
• P0335 Crankshaft position sensor (POS)
• P0340 Camshaft position sensor (PHASE)
• P0500 Vehicle speed sensor
• P0520 Engine oil pressure sensor
• P0603 P0604 P0605 P0606 P0607 P060A P060B ECM
• P0643 Sensor power supply
• P0850 Park/neutral position (PNP) switch
• P1550 P1551 P1552 P1553 P1554 Battery current sensor
• P1610 - P1615 NATS
• P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
2 • P0030 P0031 P0032 Air fuel ratio (A/F) sensor 1 heater • P0037 P0038 Heated oxygen sensor 2 heater
• P0075 Intake valve timing control solenoid valve
• P0078 Exhaust valve timing control solenoid valve
• P0130 P0131 P0132 P0133 P014C P014D P015A P015B P2096 P2097 Air fuel ratio (A/F) sensor 1
• P0137 P0138 P0139 Heated oxygen sensor 2
• P0441 EVAP control system purge flow monitoring
• P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
• P0447 P0448 EVAP canister vent control valve
• P0451 P0452 P0453 EVAP control system pressure sensor
• P0460 P0461 P0462 P0463 Fuel level sensor
• P059F Active grille shutter
• P1078 Exhaust valve timing control position sensor
• P1217 Engine over temperature (OVERHEAT)
• P1805 Brake switch
• P2100 P2103 Throttle control motor relay
• P2101 Electric throttle control function
• P2118 Throttle control motor
3 • P0011 Intake valve timing control • P0014 Exhaust valve timing control
• P0171 P0172 Fuel injection system function
• P0300 - P0304 Misfire
• P0420 Three way catalyst function
• P0456 EVAP control system (VERY SMALL LEAK)
• P0506 P0507 Idle speed control system
• P050A P050B P050E Cold start control
• P0524 Engine oil pressure
• P1148 Closed loop control
• P1212 TCS communication line
• P1564 ASCD steering switch
• P1572 ASCD brake switch
• P1574 ASCD vehicle speed sensor
• P1715 Input speed sensor
• P1720 Vehicle speed sensor
• P2119 Electric throttle control actuator
• P219A P219C P219D P219E P219F Air fuel ratio (A/F) sensor 1
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1252 of 3641
![NISSAN NOTE 2016 Service Repair Manual ADDITIONAL SERVICE WHEN REPLACING ECMEC-125
< BASIC INSPECTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ADDITIONAL SERVICE WHEN REPLACING ECM
DescriptionINFOID:0000000012431350
When replacing ECM, t](/img/5/57363/w960_57363-1251.png "NISSAN NOTE 2016 Service Repair Manual ADDITIONAL SERVICE WHEN REPLACING ECMEC-125
< BASIC INSPECTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ADDITIONAL SERVICE WHEN REPLACING ECM
DescriptionINFOID:0000000012431350
When replacing ECM, t")
ADDITIONAL SERVICE WHEN REPLACING ECMEC-125
< BASIC INSPECTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ADDITIONAL SERVICE WHEN REPLACING ECM
DescriptionINFOID:0000000012431350
When replacing ECM, the following procedure mu
st be performed. (For details, refer to EC-125, "Work Proce-
dure".)
PROGRAMMING OPERATION
NOTE:
After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the pro-
cedure to perform the programming.
Work ProcedureINFOID:0000000012431351
1.CHECK ECM PART NUMBER
Check ECM part number to see whether it is blank ECM or not.
NOTE:
• Part number of blank ECM is 23703 - ×××××.
• Check the part number when ordering ECM or with the one included in the label on the container box.
Is the ECM a blank ECM?
YES >> GO TO 2.
NO >> GO TO 4.
2.SAVE ECM PART NUMBER
Read out the part number from the old ECM and save the number, following the programming instructions.
Refer to “CONSULT Operation Manual”.
NOTE:
• The ECM part number is saved in CONSULT.
• Even when ECM part number is not saved in CONSULT, go to 3.
>> GO TO 3.
3.PERFORM ECM PROGRAMMING
After replacing ECM, perform the ECM program ming. Refer to “CONSULT Operation Manual”.
NOTE:
• Refer to EC-477, "
Removal and Installation" for replacement of ECM.
• During programming, maintain the following conditions:
- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 – 13.5 V (Be sure to check the va lue of battery voltage by selecting “BATTERY VOLT” in
“Data monitor” of CONSULT.)
>> GO TO 4.
4.REPLACE ECM
Replace ECM. Refer to EC-477, "
Removal and Installation".
>> GO TO 5.
5.PERFORM VIN REGISTRATION
Refer to EC-127, "
Description".
>> GO TO 6.
6.PERFORM INITIALIZATION OF NATS SYSTEM AND REGISTRATION OF ALL NATS IGNITION KEY IDS
Refer to SEC-49, "
ECM : Description"(with I-Key), SEC-142, "ECM RE-COMMUNICATING FUNCTION :
Description"(without I-Key).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1257 of 3641
![NISSAN NOTE 2016 Service Repair Manual EC-130
< BASIC INSPECTION >[HR16DE]
IDLE AIR VOLUME LEARNING
IDLE AIR VOLUME LEARNING
DescriptionINFOID:0000000012431358
Idle Air Volume Learning is a function of ECM to learn the idle air volume that](/img/5/57363/w960_57363-1256.png "NISSAN NOTE 2016 Service Repair Manual EC-130
< BASIC INSPECTION >[HR16DE]
IDLE AIR VOLUME LEARNING
IDLE AIR VOLUME LEARNING
DescriptionINFOID:0000000012431358
Idle Air Volume Learning is a function of ECM to learn the idle air volume that")
EC-130
< BASIC INSPECTION >[HR16DE]
IDLE AIR VOLUME LEARNING
IDLE AIR VOLUME LEARNING
DescriptionINFOID:0000000012431358
Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps each engine idle speed
within the specific range. It must be performed under any of the following conditions:
• Each time electric throttle control actuator or ECM is replaced.
• Idle speed or ignition timing is out of specification.
Refer to
EC-130, "
Work Procedure".
Work ProcedureINFOID:0000000012431359
1.PRECONDITIONING
Make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the follo wing conditions are missed for even a moment.
• Battery voltage: More than 12.9 V (At idle)
• Engine coolant temperature: 70 - 100 °C (158 - 212° F)
• Selector lever: P or N (CVT), Neutral (M/T)
• Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
- For vehicles equipped with dayt ime light systems, perform one of the following procedures before
starting engine not to illuminate headlamps.
• Apply parking brake
• Set lighting switch to the 1st position
• Steering wheel: Neutral (Straight-ahead position) position
• Vehicle speed: Stopped
• Transmission: Warmed-up
- CVT models
• With CONSULT: Drive vehicle until “FLUID TEMP SE ” in “DATA MONITOR” mode of “TRANSMISSION” sys-
tem indicates less than 0.9 V.
• Without CONSULT: Drive vehicle for 10 minutes.
- M/T models
• Drive vehicle for 10 minutes.
Do you have CONSULT?
YES >> GO TO 2.
NO >> GO TO 3.
2.IDLE AIR VOLUME LEARNING
With CONSULT
1. Perform ACCELERATOR PEDAL RELEAS ED POSITION LEARNING. Refer to EC-128, "
Description".
2. Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to EC-129, "
Description".
3. Start engine and warm it up to normal operating temperature.
4. Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode with CONSULT.
5. Touch “START” and wait 20 seconds.
Is
“CMPLT” displayed on CONSULT screen?
YES >> GO TO 4.
NO >> GO TO 5.
3.IDLE AIR VOLUME LEARNING
Without CONSULT
NOTE:
• It is better to count the ti me accurately with a clock.
• It is impossible to switch the di agnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1. Perform ACCELERATOR PEDAL RELEAS ED POSITION LEARNING. Refer to EC-128, "
Description".
2. Perform THROTTLE VALVE CLOSED POSITION LEARNING. Refer to EC-129, "
Description".
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Confirm that accelerator pedal is fully releas ed, turn ignition switch ON and wait 3 seconds.
Revision: August 2015 2016 Versa Note
cardiagn.com