Heat NISSAN NOTE 2016 Service Owner's Guide

COMPONENT PARTSEC-17
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ENGINE CONTROL SYSTEM : Component DescriptionINFOID:0000000012431270
1. ASCD steering switch
2. Active grille shutter3. Fuel level sensor unit and fuel pump
4. Fuel tank temperature sensor 5. EVAP control system pressure sen- sor6. EVAP canister
7. EVAP canister vent control valve 8. ASCD brake switch 9. Stop lamp switch
10. Clutch pedal position switch 11. Accelerator pedal position sensor
A. Fuel tank B. Rear under bodyC. Periphery of pedals
ALBIA1072ZZ
Component Reference
ECM EC-20, "
ECM"
A/F sensor 1EC-19, "Air Fuel Ratio Sensor 1"
A/F sensor 1 heaterEC-19, "Air Fuel Ratio Sensor 1 Heater"
Accelerator pedal position sensorEC-18, "Accelerator Pedal Position Sensor"
Cooling fan motor EC-20, "Cooling Fan"
Crankshaft position sensorEC-20, "Crankshaft Position Sensor"
Electric throttle control actuatorEC-21, "Electric Throttle Control Actuator"
Engine coolant temperature sensorEC-21, "Engine Coolant Temperature Sensor"
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-18
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Accelerator Pedal Position Sensor
INFOID:0000000012431271
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometer which transform the accelerator pedal
position into output voltage, and emit the voltage signals to the ECM.
The ECM judges the current opening angle of the accelerator pedal
from these signals and controls the throttle control motor based on
these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for the engine operation such as fuel cut.
Engine oil pressure sensor EC-21, "Engine Oil Pressure Sensor"
Engine oil temperature sensorEC-21, "Engine Oil Temperature Sensor"
EVAP canister purge volume control solenoid valveEC-22, "EVAP Canister Purge Volume Control Solenoid Valve"
EVAP canister vent control valveEC-22, "EVAP Canister Vent Control Valve"
EVAP control system pressure sensorEC-22, "EVAP Control System Pressure Sensor"
Exhaust valve timing control position sensor EC-19, "Camshaft Position Sensor"
Exhaust valve timing control solenoid valveEC-23, "Exhaust Valve Timing Control Solenoid Valve"
Fuel injectorEC-23, "Fuel Injector"
Fuel pumpEC-23, "Fuel Pump"
Heated oxygen sensor 2EC-24, "Heated Oxygen Sensor 2"
Heated oxygen sensor 2 heaterEC-24, "Heated Oxygen Sensor 2 Heater"
Ignition coil (with power transistor)EC-24, "Ignition Coil With Power Transistor"
Intake air temperature sensorEC-24, "Intake Air Temperature Sensor"
Camshaft position sensorEC-19, "Camshaft Position Sensor"
Intake valve timing control solenoid valveEC-25, "Intake Valve Timing Control Solenoid Valve"
Knock sensorEC-25, "Knock Sensor"
Mass air flow sensorEC-26, "Mass Air Flow Sensor"
PCV valveEC-28, "Positive Crankcase Ventilation"
Refrigerant pressure sensorEC-27, "Refrigerant Pressure Sensor"
Stop lamp switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Throttle control motorEC-27, "Throttle Control Motor"
Throttle control motor relay EC-27, "Throttle Control Motor Relay"
Throttle position sensor EC-27, "Throttle Position Sensor"
ASCD steering switchEC-27, "ASCD Steering Switch"
ASCD brake switchEC-27, "Stop Lamp Switch & ASCD Brake Switch"
Clutch pedal position switchEC-20, "Clutch Pedal Position Switch"
Active grille shutterEXT-10, "ACTIVE GRILLE SHUTTER SYSTEM : Active grille shutter"
Component Reference
PBIB1741E
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSEC-19
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Air Fuel Ratio Sensor 1INFOID:0000000012431272
The air fuel ratio (A/F) sensor 1 is a planar one-cell limit current sen-
sor. The sensor element of the A/F sensor 1 is composed an elec-
trode layer, which transports ions. It has a heater in the element.
The sensor is capable of precise m
easurement = 1, but also in the
lean and rich range. Together with its control electronics, the sensor
outputs a clear, continuous signal throughout a wide range.
The exhaust gas components diffuse through the diffusion layer at
the sensor cell. An electrode layer is applied voltage, and this current
relative oxygen density in lean. Also this current relative hydrocar-
bon density in rich.
Therefore, the A/F sensor 1 is able to indicate air fuel ratio by this
electrode layer of current. In addition, a heater is integrated in the
sensor to ensure the required operating temperature of about 800 °C
(1,472 °F).
Air Fuel Ratio Sensor 1 HeaterINFOID:0000000012431273
SYSTEM DESCRIPTION
The ECM performs ON/OFF duty control of the A/F sensor 1 heater corresponding to the engine operating
condition to keep the temperature of A/F s ensor 1 element within the specified range.
Camshaft Position SensorINFOID:0000000012431274
The camshaft position sensor senses the protrusion of camshaft to
identify a particular cylinder. The camshaft position sensor senses
the piston position.
When the crankshaft position sensor system becomes inoperative,
the camshaft position sensor provides various controls of engine
parts instead, utilizing timing of cylinder identification signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic fiel d, the voltage from the sensor
changes.
JMBIA0112GB
PBIB3354E
Sensor Input Signal to ECM ECM functionActuator
Camshaft position sensor (PHASE)
Crankshaft position sensor (POS) Engine speed
Air fuel ratio (A/F) sensor 1
heater controlAir fuel ratio (A/F) sensor 1
heater
Mass air flow sensor Amount of intake air
PBIA9209J
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-24
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
Heated Oxygen Sensor 2
INFOID:0000000012431289
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas.
Even if switching characteristics of the air fuel ratio (A/F) sensor 1
are shifted, the air-fuel ratio is cont rolled to stoichiometric, by the sig-
nal from the heated oxygen sensor 2.
This sensor is made of ceramic zirconia. The zirconia generates volt-
age from approximately 1 V in richer conditions to 0 V in leaner con-
ditions.
Under normal conditions the heated ox ygen sensor 2 is not used for
engine control operation.
Heated Oxygen Sensor 2 HeaterINFOID:0000000012431290
SYSTEM DESCRIPTION
The ECM performs ON/OFF control of the heated oxy gen sensor 2 heater corresponding to the engine speed,
amount of intake air and engine coolant temperature.
OPERATION
Ignition Coil With Power TransistorINFOID:0000000012431291
The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor turns
ON and OFF the ignition coil primary circuit. This ON/O FF operation induces the proper high voltage in the coil
secondary circuit.
Intake Air Temperature SensorINFOID:0000000012431292
The intake air temperature sensor is built-into mass air flow sensor
(1). The sensor detects intake air temperature and transmits a signal
to the ECM.
The temperature sensing unit uses a thermistor which is sensitive to
the change in temperature. Electrical resistance of the thermistor
decreases in response to the temperature rise.
SEF327R
Sensor Input signal to ECM ECM function Actuator
Camshaft position sensor (PHASE)
Crankshaft position sensor (POS) Engine speed
Heated oxygen sensor 2
heater controlHeated oxygen sensor 2 heater
Engine coolant temperature sensor Engine coolant temperature
Mass air flow sensor Amount of intake air
Engine speed Heated oxygen sensor 2 heater
Above 3,600 rpm OFF
Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load ON
PBIA9559J
Revision: August 2015
2016 Versa Note

cardiagn.com

EC-26
< SYSTEM DESCRIPTION >[HR16DE]
COMPONENT PARTS
BATTERY TEMPERATURE SENSOR
Battery temperature sensor is int
egrated in battery current sensor.
The sensor measures temperature around the battery.
The electrical resistance of the t hermistor decreases as temperature
increases.

*: These data are reference values and are measured between battery temperature
sensor signal terminal and sensor ground.
Malfunction Indicator Lamp (MIL)INFOID:0000000012431296
The MIL is located on the combination meter.
The MIL will illuminate when the ignition switch is turned ON without
the engine running. This is a bulb check.
When the engine is started, the MIL should turn OFF. If MIL remains
ON or continues blinking, the on board diagnostic system detects a
DTC(s) that affects exhaust gas.
For details, refer to EC-57, "
DIAGNOSIS DESCRIPTION : Malfunc-
tion Indicator Lamp (MIL)".
Mass Air Flow SensorINFOID:0000000012431297
The mass air flow sensor (1) is placed in the stream of intake air. It
measures the intake flow rate by measuring a part of the entire
intake flow. The mass air flow sensor controls the temperature of the
hot wire to a certain amount. The heat generated by the hot wire is
reduced as the intake air flows around it. The more air, the greater
the heat loss.
Therefore, the electric current supplied to hot wire is changed to
maintain the temperature of the hot wire as air flow increases. The
ECM detects the air flow by means of this current change.
Oil Pressure Warning LampINFOID:0000000012431298
Oil pressure warning lamp is located on the combination meter.
It indicates the low pressure of the engine oil and the malfunction of
the engine oil pressure system.
Combination meter turns the oil pressure warning lamp ON/OFF
according to the oil pressure warning lamp signal received from
ECM via CAN communication.
For details, refer to EC-43, "
ENGINE PROTECTION CONTROL AT
LOW ENGINE OIL PRESSURE : System Description".
Temperature [°C ( °F)]
Vo l ta g e* (V) Resistance (k
Ω)
25 (77) 3.3331.9 - 2.1
90 (194) 0.9690.222 - 0.258
SEF012P
SAT652J
PBIA9559J
PBIA8559J
Revision: August 2015 2016 Versa Note

cardiagn.com

SYSTEMEC-33
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*1: M/T models
*2: CVT models
*3: This sensor is not used to contro
l the engine system under normal conditions.
*4: ECM determines the start signal status by the signals of engine speed and battery voltage.
*5: This signal is sent to the ECM through CAN communication line.
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). T he amount of fuel injected is a program value in the
ECM memory. The program value is preset by engine operating conditions. These conditions are determined
by input signals (for engine speed and intake air) from the crankshaft position sensor, camshaft position sen-
sor and the mass air flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compensated to improve engine performance under various operat-
ing conditions as listed below.

• During warm-up
• When starting the engine
• During acceleration
• Hot-engine operation
• When selector lever position is changed from N to D (CVT models)
• High-load, high-speed operation
• During deceleration
• During high engine speed operation
Sensor Input signal to ECM ECM functionActuator
Crankshaft position sensor (POS) Engine speed
*4
Piston position
Fuel injection & mixture
ratio controlFuel injector
Camshaft position sensor (PHASE)
Mass air flow sensor
Amount of intake air
Intake air temperature sensor Intake air temperature
Engine coolant temperature sensor Engine coolant temperature
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Park/neutral position (PNP) switch
*1
PNP signal
Transmission range switch*2
Battery Battery voltage*4
Knock sensor Engine knocking condition
Heated oxygen sensor 2
*3Density of oxygen in exhaust gas
EPS control unit EPS operation signal
*5
Combination meter
Vehicle speed*5
BCMA/C ON signal*5
Blower fan signal*5
Revision: August 2015
2016 Versa Note

cardiagn.com

EC-34
< SYSTEM DESCRIPTION >[HR16DE]
SYSTEM
MIXTURE RATIO FEEDBACK CONTROL (CLOSED LOOP CONTROL)
The mixture ratio feedback sys
tem provides the best air-fuel mixture ra tio for drivability and emission control.
The three way catalyst (manifold) can better reduce CO, HC and NOx emissions. This system uses A/F sen-
sor 1 in the exhaust manifold to monitor whether the engine operation is rich or lean. The ECM adjusts the
injection pulse width according to the sensor voltage signal. For more information about A/F sensor 1, refer to
EC-19, "
Air Fuel Ratio Sensor 1". This maintains the mixture ratio within the range of stoichiometric (ideal air-
fuel mixture).
This stage is referred to as the closed loop control condition.
Heated oxygen sensor 2 is located downstream of the th ree way catalyst (manifold). Even if the switching
characteristics of A/F sensor 1 shift, the air-fuel ratio is controlled to stoichiometric by the signal from heated
oxygen sensor 2.
• Open Loop Control The open loop system condition refers to when the ECM detects any of the following conditions. Feedback
control stops in order to maintain stabilized fuel combustion.
- Deceleration and acceleration
- High-load, high-speed operation
- Malfunction of A/F sensor 1 or its circuit
- Insufficient activation of heated sensor 1 at low engine coolant temperature
- High engine coolant temperature
- During warm-up
- After shifting from N to D (CVT models)
- When starting the engine
MIXTURE RATIO SELF-LEARNING CONTROL
The mixture ratio feedback control system monitors t he mixture ratio signal transmitted from A/F sensor 1.
This feedback signal is then sent to the ECM. The ECM c ontrols the basic mixture ratio as close to the theoret-
ical mixture ratio as possible. However, the basic mi xture ratio is not necessarily controlled as originally
designed. Both manufacturing differences (i.e., mass ai r flow sensor hot wire) and characteristic changes dur-
ing operation (i.e., fuel injector clogging) directly affect mixture ratio.
Accordingly, the difference between the basic and theoretical mixture ratios is monitored in this system. This is
then computed in terms of “injection pulse duration” to automatically compensate for the difference between
the two ratios.
“Fuel trim” refers to the feedback compensation value co mpared against the basic injection duration. Fuel trim
includes “short-term fuel trim” and “long-term fuel trim”.
“Short-term fuel trim” is the short-term fuel compensation used to maintain the mixture ratio at its theoretical
value. The signal from A/F sensor 1 indicates whether the mixture ratio is RICH or LEAN compared to the the-
oretical value. The signal then triggers a reduction in fuel volume if the mixture ratio is rich, and an increase in
fuel volume if it is lean.
“Long-term fuel trim” is overall fuel compensation carried out long-term to compensate for continual deviation
of the “short-term fuel trim” from the central value. Such deviation will occur due to individual engine differ-
ences, wear over time and changes in the usage environment.
PBIB2793E
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-62
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
MAS A/F SE-B1
VThe signal voltage of the mass air flow sensor is dis-
played. • When the engine is stopped, a certain
value is indicated.
• When engine is running, specification range is indica ted in “SPEC”.
B/FUEL SCHDL ms“Base fuel schedule” indicates the fuel injection
pulse width programmed into ECM, prior to any
learned on board correction. When engine is running, specification
range is indicated in “SPEC”.
A/F ALPHA-B1 %The mean value of the air-fuel ratio feedback cor-
rection factor per cycle is indicated. • When the engine is stopped, a certain
value is indicated.
• When engine is running, specification
range is indica ted in “SPEC”.
• This data also includes the data for the air-fuel ratio learning control.
COOLAN TEMP/S °C or °F The engine coolant temperature (determined by the
signal voltage of the engine coolant temperature
sensor) is displayed. When the engine coolant temperature
sensor is open or short-circuited, ECM
enters fail-safe mode. The engine cool-
ant temperature determined by the ECM
is displayed.
A/F SEN1 (B1) VThe A/F signal computed from the input signal of
the air fuel ratio (A/F) sensor 1 is displayed.
HO2S2 (B1) VThe signal voltage of the heated oxygen sensor 2 is
displayed.
HO2S2 MNTR(B1) RICH/LEAN • Display of heated oxygen sensor 2 signal.
- RICH: means the amount of oxygen after three
way catalyst is relatively small.
- LEAN: means the amount of oxygen after three
way catalyst is relatively large. When the engine is stopped, a certain
value is indicated.
VHCL SPEED SE km/h or mph The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
BATTERY VOLT V The power supply voltage of ECM is displayed.
ACCEL SEN 1 VThe accelerator pedal position sensor signal volt-
age is displayed. ACCEL SEN 2 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1
VThe throttle position sensor signal voltage is dis-
played. TP SEN 2-B1 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
TP SEN 2-B1
FUEL T/TMP SE
°C or °F The fuel temperature (determined by the signal volt-
age of the fuel tank temperature sensor) is dis-
played.
EVAP SYS PRES VThe signal voltage of EVAP control system pres-
sure sensor is displayed.
FUEL LEVEL SE VThe signal voltage of the fuel level sensor is dis-
played.
START SIGNAL ON/OFF Indicates start signal status [ON/OFF] computed by
the ECM according to the signals of engine speed
and battery voltage. After starting the engine, [OFF] is dis-
played regardless of the starter signal.
CLSD THL POS ON/OFF Indicates idle position [ON/OFF] computed by ECM
according to the accelerator pedal position sensor
signal.
AIR COND SIG ON/OFF Indicates [ON/OFF] condition of the air conditioner
switch as determined by the air conditioner signal.
PW/ST SIGNAL ON/OFF [ON/OFF] condition of the power steering system
(determined by the signal sent from EPS control
unit) is indicated.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (ECM)EC-63
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
OLOAD SIGNAL ON/OFF
• Indicates [ON/OFF] condition of the electrical
lode signal.
- ON: Rear window defogger switch is ON and/or lighting switch is 2nd position.
- OFF: Both rear window defogger switch and light-
ing switch are OFF.
IGNITION SW ON/OFFIndicates [ON/OFF] condition from ignition switch
signal.
HEATER FAN SW ON/OFF Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW ON/OFFIndicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1 msecIndicates the actual fuel injection pulse width com-
pensated by ECM according to the input signals. When the engine is stopped, a certain
computed value is indicated.
IGN TIMING BTDCIndicates the ignition timing computed by ECM ac-
cording to the input signals. When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE %“Calculated load value” indicates the value of the
current air flow divided by peak air flow.
MASS AIRFLOW g/sIndicates the mass air flow computed by ECM ac-
cording to the signal voltage of the mass air flow
sensor.
PURG VOL C/V %• Indicates the EVAP canister purge volume con-
trol solenoid valve control value computed by the
ECM according to the input signals.
• The opening becomes larger as the value in-
creases.
INT/V TIM(B1) °CA Indicates [ °CA] of intake camshaft advance angle.
EXH/V TIM B1 °CA Indicates [ °CA] of exhaust camshaft retard angle.
INT/V SOL(B1) %• The control value of the intake valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value increases.
AIR COND RLY ON/OFF The air conditioner relay control condition (deter-
mined by ECM according to the input signals) is in-
dicated.
FUEL PUMP RLY ON/OFF Indicates the fuel pump relay control condition de-
termined by ECM according to the input signals.
VENT CONT/V ON/OFF • The control condition of the EVAP canister vent
control valve (determined by ECM according to
the input signals) is displayed.
- ON: Closed
-OFF: Open
THRTL RELAY ON/OFF Indicates the throttle control motor relay control
condition determined by the ECM according to the
input signals.
COOLING FAN HI/LOW/OFF • Indicates the condition of the cooling fan (deter-
mined by ECM according to the input signals).
- HI: High speed operation
- LOW: Low speed operation
-OFF: Stop
HO2S2 HTR (B1) ON/OFF Indicates [ON/OFF] condition of heated oxygen
sensor 2 heater determined by ECM according to
the input signals.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-64
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
ALT DUTY SIG ON/OFF• The control condition of the power generation
voltage variable control (determined by ECM ac-
cording to the input signals) is indicated.
- ON: Power generation voltage variable control is active.
- OFF: Power generation voltage variable control is inactive.
I/P PULLY SPD rpmIndicates the engine speed computed from the in-
put speed sensor signal.
VEHICLE SPEED km/h or mph The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN YET/CMPLT • Displays the condition of Idle Air Volume Learn-
ing.
- YET: Idle air volume learning has not been per-
formed yet.
- CMPLT: Idle air volume learning has already been performed successfully.
TRVL AFTER MIL km or mile Distance traveled while MIL is activated.
ENG OIL TEMP °C or °F The engine oil temperature (determined by the sig-
nal voltage of the engine oil temperature sensor) is
indicated.
A/F S1 HTR(B1) %• Air fuel ratio (A/F) sensor 1 heater control value
computed by ECM according to the input signals.
• The current flow to the heater becomes larger as the value increases.
VHCL SPEED SE km/h or mph The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
SET VHCL SPD km/h or mph The preset vehicle speed is displayed.
MAIN SW ON/OFFIndicates [ON/OFF] condition from ASCD MAIN
switch signal.
CANCEL SW ON/OFFIndicates [ON/OFF] condit
ion from CANCEL switch
signal.
RESUME/ACC SW ON/OFF Indicates [ON/OFF] condition from ACCEL/RES
switch signal.
SET SW ON/OFFIndicates [ON/OFF] condition from COAST/SET
switch signal.
BRAKE SW1 ON/OFFIndicates [ON/OFF] condition from ASCD brake
switch signal.
BRAKE SW2 ON/OFFIndicates [ON/OFF] condition of stop lamp switch
signal.
VHCL SPD CUT NON/CUT • Indicates the vehicle cruise condition.
- NON: Vehicle speed is maintained at the ASCD
set speed.
- CUT: Vehicle speed decreased to excessively
low compared with the ASCD set speed, and
ASCD operation is cut off.
LO SPEED CUT NON/CUT • Indicates the vehicle cruise condition.
- NON: Vehicle speed is maintained at the ASCD
set speed.
- CUT: Vehicle speed decreased to excessively low, and ASCD operation is cut off.
AT OD MONITOR ON/OFF Indicates [ON/OFF] condition of CVT O/D accord-
ing to the input signal from the TCM.
AT OD CANCEL ON/OFF Indicates [ON/OFF] condition of CVT O/D cancel
request signal.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com