NISSAN NOTE 2016 Service Repair Manual
NOTE 2016
NISSAN
NISSAN
https://www.carmanualsonline.info/img/5/57363/w960_57363-0.png
NISSAN NOTE 2016 Service Repair Manual
Page 3165 of 3641
STARTING SYSTEMSTR-13
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
AABIA1425GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 3166 of 3641
STR-14
< WIRING DIAGRAM >
STARTING SYSTEM
ABBIA3068GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3167 of 3641
STARTING SYSTEMSTR-15
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
AABIA1111GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 3168 of 3641
STR-16
< WIRING DIAGRAM >
STARTING SYSTEM
Wiring Diagram - Without Intelligent Key System
INFOID:0000000012432069
ABBWA1634GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3169 of 3641
STARTING SYSTEMSTR-17
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
ABBIA3069GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 3170 of 3641
STR-18
< WIRING DIAGRAM >
STARTING SYSTEM
ABBIA3070GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3171 of 3641
STARTING SYSTEMSTR-19
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
ABBIA3071GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 3172 of 3641
STR-20
< WIRING DIAGRAM >
STARTING SYSTEM
ABBIA3072GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3179 of 3641

B TERMINAL CIRCUITSTR-27
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
DTC/CIRCUIT DIAGNOSIS
B TERMINAL CIRCUIT
DescriptionINFOID:0000000012432072
Terminal “B” is constantly supplied with battery power.
Diagnosis ProcedureINFOID:0000000012432073
Regarding Wiring Diagram information, refer to
STR-10, "Wiring Diagram - With Intelligent Key System" or
STR-16, "
Wiring Diagram - Without Intelligent Key System".
CAUTION:
Perform diagnosis under the cond ition that the engine cannot start by the following procedure.
1. Remove fuel pump fuse.
2. Crank or start the engine (where possi ble) until the fuel pressure is released.
1.CHECK “B” TERMINAL CIRCUIT
1. Turn ignition switch OFF.
2. Check that starter motor B” terminal connection is clean and tight.
3. Check voltage between starter motor connector F27 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check harness between battery and starter motor for open circuit.
2.CHECK BATTERY CABLE CONNECTION STATUS (VOLTAGE DROP TEST)
1. Shift selector lever to P (P ark) or N (Neutral) position.
2. Check voltage between battery positive terminal and starter motor B terminal.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between the battery and starter motor for continuity.
3.CHECK GROUND CIRCUIT STATUS (VOLTAGE DROP TEST)
1. Shift selector lever to P (P ark) or N (Neutral) position.
2. Check voltage between starter motor case and battery negative terminal.
Is the inspection result normal?
Te r m i n a l s
Voltage
(Approx.)
(+)
(-)
Starter motor “B” terminal Terminal
F27 BGround Battery voltage
Te r m i n a l s
ConditionVoltage
(Approx.)
(+) (-)
Starter motor “B“ terminal Terminal
Battery positive terminal F27 B When the ignition switch is in START position Less than 0.5V
Te r m i n a l s
ConditionVoltage
(Approx.)
(+) (-)
Starter motor case Battery negative terminal When the ignition switch is in
START position Less than 0.2V
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 3181 of 3641

S CONNECTOR CIRCUITSTR-29
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M A
STR
NP
O
S CONNECTOR CIRCUIT
DescriptionINFOID:0000000012432074
The starter motor magnetic switch is supplied with power when the ignition switch is turned to the START posi-
tion while the selector lever is in the P (Park) or N (Neutral) position.
Diagnosis ProcedureINFOID:0000000012432075
Regarding Wiring Diagram information, refer to
STR-10, "Wiring Diagram - With Intelligent Key System" or
STR-16, "
Wiring Diagram - Without Intelligent Key System".
CAUTION:
Perform diagnosis under the cond ition that engine cannot start by the following procedure.
1. Remove fuel pump fuse.
2. Crank or start the engine (where possi ble) until the fuel pressure is released.
1.CHECK “S” CONNECTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect starter motor connector.
3. Shift selector lever to “P” (Park) or “N” (Neutral) position.
4. Check voltage between starter motor harness connector F28 and ground.
Is the inspection result normal?
YES >> “S” circuit is OK. Further inspection is necessary. Refer to STR-21, "Work Flow (With GR8-1200
NI)" or STR-25, "Work Flow (Without GR8-1200 NI)".
NO >> GO TO 2.
2.CHECK HARNESS CONTINUI TY (OPEN CIRCUIT)
1. Disconnect IPDM E/R connector.
2. Check continuity between starter motor harnes s connector F28 and the IPDM E/R harness connector
E43.
3. Check continuity between starter motor connector F28 terminal S and ground.
Is the inspection result normal?
YES >> Further inspection is necessary. Refer to STR-21, "Work Flow (With GR8-1200 NI)" or STR-25,
"Work Flow (Without GR8-1200 NI)".
NO >> Repair or replace the harness or connectors.
(+) (-)
Condition Voltage
(Approx.)
Connector Terminal
F28 SGround When the ignition switch is in START position Battery voltage
Starter motor harness connector IPDM E/R harness connector
Continuity
Connector TerminalConnector Terminal
F28 SE43 6Yes
Connector Terminal –Continuity
F28 SGround No
Revision: August 2015 2016 Versa Note
cardiagn.com