diagram NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 3525 of 3641
WCS-10
< SYSTEM DESCRIPTION >
SYSTEM
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled:
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
SEAT BELT REMINDER WARNING CHIME
SEAT BELT REMINDER WARNING CHIME : Seat belt WarningINFOID:0000000012432673
SYSTEM DIAGRAM
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
Parking brake During the operation (parking brake switch ON)
Vehicle speed Approximately 4.3 MPH (7 km/h) or moreOperation conditions
Operation conditions
Ignition switch OFF
Parking brake Release condition (parking brake switch OFF)
Vehicle speed Approximately 1.9 MPH (3 km/h) or less
Signal name Signal source
Ignition switch signal —
Parking brake switch signal Parking brake switch Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
AWNIA2652GB
Operation conditions
Ignition switch ON
Driver seat belt Unfastened [seat belt buckle switch LH ON]
Operation conditions
Ignition switch OFF
Driver seat belt Fastened (seat belt buckle switch LH OFF)
6 seconds after the start of warning sound
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3526 of 3641
WCS
SYSTEMWCS-11
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec- essary from signals below.
2. Combination meter sounds integrated buzzer, followi ng the warning chime output requirement (below sig-
nal) from BCM.
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY)
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY) : Key Warning Chime
INFOID:0000000012432674
SYSTEM DIAGRAM
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
1. BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with CAN communication line.
Signal name Signal source
Ignition switch signal —
Seat belt buckle switch signal (LH) Seat belt buckle switch (LH) Combination meter BCM
Signal name Signal source
Buzzer output signal BCM Combination meter
AWNIA3130GB
Operation conditions
Ignition switch OFF or ACC position
Key switch ON (key is in key cylinder)
Driver side door Open [front door switch LH ON]
Operation conditions
Ignition switch ON
Key switch ON (key is removed from key cylinder)
Driver side door Close [front door switch LH OFF]
Signal name Signal source
Ignition switch signal —
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3541 of 3641
WCS-26
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
WIRING DIAGRAM
WARNING CHIME SYSTEM
Wiring DiagramINFOID:0000000012432684
ABNWA2884GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3542 of 3641
WCS
WARNING CHIME SYSTEMWCS-27
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M B A
O P
AANIA3164GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3543 of 3641
WCS-28
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
AANIA3165GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3544 of 3641
WCS
WARNING CHIME SYSTEMWCS-29
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M B A
O P
ABNIA8037GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3545 of 3641
WCS-30
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
ABNIA8038GB
Revision: August 20152016 Versa Note
cardiagn.com
Page 3546 of 3641
WCS
WARNING CHIME SYSTEMWCS-31
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K L
M B A
O P
ABNIA8039GB
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3549 of 3641
WCS-34
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER (TYPE A)
COMBINATION METER (TYPE A) : Diagnosis ProcedureINFOID:0000000012542990
Regarding Wiring Diagram information, refer to MWI-26, "Wiring Diagram".
1.CHECK FUSE
Check that the following fuses are not blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect combination meter connector.
2. Check voltage between combination meter harness connector M82, terminals 27, 28, 15 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.GROUND CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter har ness connector M82, terminals 21, 22, 23 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
COMBINATION METER (TYPE B)
Power source Fuse No.
Battery 8
Ignition switch ON or START 3
Ignition switch ACC or ON 18
TerminalsIgnition switch position
(+) (–)OFF ACC ONSTART
Connector Terminal
M82 27
GroundBattery voltage Battery voltage Battery voltage Battery voltage
28 0V0VBattery voltage Battery voltage
15 0V Battery voltage Battery voltage 0V
Te r m i n a l s
Continuity
(+)
(–)
Connector Terminal
M82 21
Ground Yes
22
23
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 3550 of 3641
WCS
POWER SUPPLY AND GROUND CIRCUITWCS-35
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
COMBINATION METER (TYPE B) : Diagnosis ProcedureINFOID:0000000012542991
Regarding Wiring Diagram information, refer to MWI-79, "Wiring Diagram".
1.CHECK FUSE
Check that the following fuses are not blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect combination meter connector.
2. Check voltage between combination meter harness connector M24, terminals 27, 28, 15 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.GROUND CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector M24, terminals 21, 22, 23 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (W ITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH IN TELLIGENT KEY SYSTEM) : Diagnosis
Procedure
INFOID:0000000012542992
Regarding Wiring Diagram information, refer to BCS-52, "Wiring Diagram".
Power source Fuse No.
Battery 8
Ignition switch ON or START 3
Ignition switch ACC or ON 18
TerminalsIgnition switch position
(+) (–)OFF ACC ONSTART
Connector Terminal
M24 27
GroundBattery voltage Battery voltage Battery voltage Battery voltage
28 0V0VBattery voltage Battery voltage
15 0V Battery voltage Battery voltage 0V
Te r m i n a l s
Continuity
(+)
(–)
Connector Terminal
M24 21
Ground Yes
22
23
Revision: August 2015 2016 Versa Note
cardiagn.com