fuse chart NISSAN NOTE 2016 Service Repair Manual

C1130 ENGINE SIGNALBRC-93
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT Check the ABS actuator and electr ic unit (control unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness, connector, fuse, or fusible link.
3.CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect ECM harness connector.
3. Disconnect ABS actuator and electric unit (control unit) harness connector.
4. Check the connector for disconnection or looseness.
5. Check the pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness, connector, or terminal, securely lock the connector, and GO TO 4.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
1. Connect ECM harness connector.
2. Connect ABS actuator and electric unit (control unit) harness connector.
3. Erase “Self Diagnostic Result” of “ABS”
4. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
6. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1130” or “U1000” detected?
YES (“C1130”)>>GO TO 1.
YES (“U1000”)>>Refer to LAN-16, "
Trouble Diagnosis Flow Chart".
NO >> Inspection End.
Revision: August 2015 2016 Versa Note

cardiagn.com

C1143 STEERING ANGLE SENSORBRC-101
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
YES >> GO TO 7.
NO >> GO TO 6.
6.CHECK STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check fuse 50 (10A).
3. Disconnect IPDM E/R harness connector.
4. Check the continuity between steering angle sens or harness connector and IPDM E/R harness connector.
5. Check the continuity between steeri ng angle sensor harness connector and ground.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply.
NO >> Repair / replace harness, connector, or fuse.
7.CHECK STEERING ANGLE SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check the continuity between steeri ng angle sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair / replace harness or connector.
8.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT Check the ABS actuator and electr ic unit (control unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair / replace harness, connector, fuse, or fusible link.
9.CHECK TERMINAL
1. Check the steering angle sensor pin terminals for damage or loose connection with harness connector.
2. Check the IPDM E/R pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair / replace harness, connector, or terminal.
10.CHECK CAN COMMUNICATION LINE
Check the CAN communication line. Refer to LAN-16, "
Trouble Diagnosis Flow Chart".
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair / replace harness or connector.
11 .CHECK DATA MONITOR
Steering angle sensor IPDM E/R
Continuity
Connector TerminalConnector Terminal
M64 4E45 20Yes
Steering angle sensor
—Continuity
Connector Terminal
M64 4Ground No
Steering angle sensor
—Continuity
Connector Terminal
M64 1Ground Yes
Revision: August 2015 2016 Versa Note

cardiagn.com