engine NISSAN PATROL 2004 Electronic Manual PDF

Engine Room Harness/RHD Models
GASOLINE ENGINE MODELS
TEL083V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
EL-4322

TEL084V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Engine Room Harness/RHD Models (Cont'd)EL-4323

DIESEL ENGINE MODELS
TEL085V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Engine Room Harness/RHD Models (Cont'd)EL-4324

TEL086V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Engine Room Harness/RHD Models (Cont'd)EL-4325

PASSENGER COMPARTMENT
TEL087V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Engine Room Harness/RHD Models (Cont'd)EL-4326

TEL088V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Engine Room Harness/RHD Models (Cont'd)EL-4327

Engine Harness
ZD ENGINE
TEL089V
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
EL-4328

Wiring Diagram Codes (Cell Codes)
Use the chart below to ®nd out what each wiring diagram code
stands for.
Refer to the wiring diagram code in the alphabetical index to ®nd
the location (Page number) of each wiring diagram.
Code Section Wiring Diagram Name
A/C, A HA Auto Air Conditioner
A/C, M HA Manual Air Conditioner
A/CCUT EC Air Conditioner Control
A/T AT A/T
ASCD EL Automatic Speed Control Device
AUDIO EL Audio
BACK/L EL Back-up Lamp
CD/CHG EL CD Auto Changer
CHIME EL Warning Chime
COMPAS EL Compass and Thermometer
COOL/B HA Cool Box
D/LOCK EL Power Door Lock
DEF EL Rear Window Defogger
DEICER EL Wiper Deicer
DTRL EL Headlamp Ð Daytime Light System
F/FOG EL Front Fog Lamp
FICD EC IACV-FICD Solenoid Valve
GLOW EC Quick Glow System
H/AIM EL Headlamp Aiming Control System
H/LAMP EL Headlamp
HEATUP EC Heat Up Switch
HLC EL Headlamp Washer
HORN EL Horn
HSEAT EL Heated Seat
ILL EL Illumination
LOAD EC Electrical Load Signal
MAFS EC Mass Air Flow Sensor
METER EL Meter and Gauges
MIRROR EL Door Mirror
MULTI EL Multi-remote Control System
NATS EL Nissan Anti-Theft System
NAVI EL Navigation System
NONDTC AT Non-detective Items
P/ANT EL Power Antenna
PHONE EL Telephone
POWER EL Power Supply Routing
R/COOL HA Rear Cooler System
R/FOG EL Rear Fog LampCode Section Wiring Diagram Name
R/HEAT HA Rear Heater System
REMOTE EL Audio (Remote Control Switch)
ROOM/L EL Interior Room Lamp
S/LOCK EL Power Door Lock Ð Super Lock
S/TANK FE Sub Fuel Tank Control System
SRS RS Supplemental Restraint System
STAB RA Stabilizer Release Device
STOP/L EL Stop Lamp
TAIL/L EL Parking, License and Tail Lamps
THEFT EL Theft Warning System
TRQ/SG EC Engine Torque Control Signal
TURN EL Turn Signal and Hazard Warning
Lamps
VSS EC Vehicle Speed Sensor
WARN EL Warning Lamps
WINDOW EL Power Window
WIP/R EL Rear Wiper and Washer
WIPER EL Front Wiper and Washer
WIRING DIAGRAM CODES (CELL CODES)
EL-4347

ENGINEMECHANICAL
SECTION
EM
MODIFICATION NOTICE:
+ Valve lifter of ZD30DDTi engine has been changed from a type without shim to a type with adjusting shim.
CONTENTS
PREPARATION ..........................................................4002
Special Service Tools ............................................4002
ZD
CAMSHAFT...............................................................4003
Removal and Installation .......................................4003
Inspection...............................................................4003
VALVE CLEARANCE INSPECTIONS AND
ADJUSTMENTS .........................................................4005 Adjustments ...........................................................4005
TIMING GEAR ...........................................................4008
Removal and Installation .......................................4008
Removal .................................................................4009
Installation ..............................................................4012
CYLINDER HEAD ......................................................4016
Disassembly and Assembly ...................................4016
SERVICE DATA AND SPECIFICATIONS (SDS) ......4017
Valve ......................................................................4017
EM-4001

Adjustments
NOTE:
Adjust valve clearance while engine is cold.
+Remove the adjusting shim for parts which are outside the
speci®ed valve clearance.
1. Remove the spill tube. Refer to ªBASIC SERVICE PROCE-
DUREº in EC section.
2. Rotate the crankshaft to face the cam nose for adjusting shims
that are to be removed upward.
3. Thoroughly wipe off engine oil on the upper side of the cylinder
head (for the air gun used in step 7).
4. Move the round hole of the adjusting shim to the front with an
extra-®ne screwdriver or like that.
CAUTION:
Perform (the above procedure) while camshaft do not contact
with adjusting shim.
5. Grip the camshaft with camshaft pliers (SST), then using the
camshaft as a support point, push the adjusting shim downward
to compress the valve spring.
CAUTION:
Do not damage the camshaft, cylinder head, and the outer cir-
cumference of the valve lifter.
6. With the valve spring in a compressed state, remove the cam-
shaft pliers (SST) by securely setting the outer circumference
of the valve lifter with the end of the lifter stopper (SST).
+Hold the lifter stopper by hand until the shim is removed.
CAUTION:
Do not retrieve the camshaft pliers forcefully, as the camshaft
will be damaged.
7. Remove the adjusting shim from the valve lifter by blowing air
through the round hole of the adjusting shim with an air gun.
CAUTION:
+When blowing, use goggles to protect your eye.
+To prevent any remaining oil from being blown around,
thoroughly wipe the area clean.
PBIC0373E
FEM029A
PBIC0374E
VALVE CLEARANCE INSPECTIONS AND ADJUSTMENTSZD
EM-4005