transfer NISSAN PATROL 2006 Owner's Guide

Checking Position Switch
4WD SWITCH
Transfer control lever position Continuity
4H, 4L Yes
Except above No
NEUTRAL POSITION SWITCH
Transfer control lever position Continuity
Between 4H and 4L
(``PUSH'' position)Ye s
Except above No
SMT252D
SMT253D
ON-VEHICLE SERVICE
TF-7

Removal
1. Drain ¯uid and oil from transfer and transmission (M/T model
only).
2. Remove exhaust front and rear tubes. Refer to FE section
(``EXHAUST SYSTEM'').
3. Remove front and rear propeller shaft. Refer to PD section
(``Removal and Installation'', ``PROPELLER SHAFT'').
4. Disconnect neutral position switch and 4WD switch harness
connectors.
5. Remove transfer control lever from transfer cross shaft.
6. Remove transfer from transmission.
WARNING:
Support transfer while removing it.
Installation
+Apply recommended sealant to mating surface to transmission.
(M/T models only)
Recommended sealant:
Genuine anaerobic liquid gasket, Three Bond
TB1215, Loctite Part No. 51813 or equivalent
+Tighten transfer bolts.
Transfer ®xing bolts:
:32-42Nzm (3.3 - 4.3 kg-m, 24 - 31 ft-lb)
SMT251D
SMT268D
SMT176BA
REMOVAL AND INSTALLATION
TF-8

SMT254D
TRANSFER GEAR CONTROL
TF-9

General Speci®cations
Transfer model TX12A
Gear ratioHigh 1.000
Low 2.020
Number of teethMain gear 29
Low gear 37
Counter
gearHigh 38
Low 24
Front drive sprocket 41
Front drive shaft 41
Fluid capacity liters (Imp qt) 1.9 (1-5/8)
Inspection and Adjustment
GEAR END PLAY
Unit: mm (in)
Front drive sprocket 0.20 - 0.35 (0.0079 - 0.0138)
Low gear 0.20 - 0.35 (0.0079 - 0.0138)
Counter gear 0 - 0.2 (0 - 0.008)
CLEARANCE BETWEEN BAULK RING AND
CLUTCH GEAR
Unit: mm (in)
Standard Wear limit
1.0 - 1.5 (0.039 - 0.059) 0.5 (0.020)
AVAILABLE SNAP RING
Mainshaft front bearing
Unit: mm (in)
Allowable clearance 0 - 0.15 (0 - 0.0059)
Thickness Part number
3.0 (0.118)
3.1 (0.122)
3.2 (0.126)33138-73P10
33138-73P11
33138-73P12
Main gear bearing
Unit: mm (in)
Allowable clearance 0 - 0.15 (0 - 0.0059)
Thickness Part number
2.6 (0.102)
2.7 (0.106)
2.8 (0.110)33114-73P00
33114-73P01
33114-73P02
AVAILABLE SHIM
Counter gear rear bearing
Distance ``A''
mm (in)Shim(s)
Thickness mm (in) Part number
40.6 - 40.5
(1.598 - 1.594)Not necessary
40.5 - 40.4
(1.594 - 1.591)0.1 (0.004) 33112-C6900
40.4 - 40.3
(1.591 - 1.587)0.2 (0.008) 33112-C6901
40.3 - 40.2
(1.587 - 1.583)0.3 (0.012) 33112-C6902
40.2 - 40.1
(1.583 - 1.579)0.4 (0.016) 33112-C6903
40.1 - 40.0
(1.579 - 1.575)0.5 (0.020) 33112-33G00
40.0 - 39.9
(1.575 - 1.571)0.6 (0.024) 33112-33G01
SMT335A
SERVICE DATA AND SPECIFICATIONS (SDS)
TF-33