engine oil capacity NISSAN PRIMERA 1999 Electronic Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1999, Model line: PRIMERA, Model: NISSAN PRIMERA 1999Pages: 2267, PDF Size: 35.74 MB
Page 1967 of 2267
General Specifications
COMPRESSOR
ModelCD20T engine SR20DE, QG16×18DE engine
CALSONIC make CR-14 CALSONIC make CSV613
Type Vane rotary Variable displacement
Displacement cm
3(cu in)/Rev 144 (8.79) 6 to 125 (0.37 to 7.63)
Direction of rotationClockwise
(Viewed from drive end)
Drive belt CD engine model: Type A Poly V
LUBRICANT
Model CALSONIC make CR-14 CALSONIC make CSV613
Name Nissan A/C System Oil Type R Nissan A/C system Oil Type S
Part number KLH00-PAGR0 KLH00-PAGS0
Capacity m(Imp fl oz)
Total in system 180 (6.3) 200 (7.04)
Compressor (Service parts)
charging amount180 (6.3) 200 (7.04)
REFRIGERANT
Type HFC-134a
Capacity kg (lb) 0.60 0.05 (1.32 0.11)
Inspection and Adjustment
ENGINE IDLING SPEED
When A/C is ON
Refer to EC section.
BELT TENSION
Refer to Checking Drive Belts (MA section).
COMPRESSOR
Model CR-14/CSV613
Clutch disc-to-pulley clearance
mm (in)0.3 - 0.6
(0.012 - 0.024)
SERVICE DATA AND SPECIFICATIONS (SDS)AUTO
HA-118
Page 2033 of 2267
Fluids and Lubricants
Capacity (Approximate)
Recommended fluids and
lubricants
Liter Imp measure
Engine oil (Refill)
With oil filterQG16DE/QG18DE 2.9 5-1/8 pts
Petrol engines:
API SH or SJ*/ACEA A2/96
Diesel engines:
ACEA B2-96 (CCMC-PD2)* SR20DE 3.7 6-1/2 pts
CD20T 5.0 8-3/4 pts
Without oil filterQG16DE/QG18DE 2.7 4-3/4 pts
SR20DE 3.5 6-1/8 pts
CD20T 4.5 7-7/8 pts
Cooling system (With
reservoir tank)QG16DE/QG18DE 6.1 10-3/4 pts
Genuine NISSAN Anti-freeze
Coolant (L2N) or equivalent. SR20DEM/T 6.6 11-5/8 pts
CVT 6.8 12 pts
CD20T 6.4 11-1/4 pts
Reservoir 0.8 1-3/8 pts
Manual transmission
gear oilRS5F70A 3.0 5-1/4 pts
Genuine NISSAN XZ gear oil or
exact equivalent.
RS5F32A 3.6 6-3/8 pts
CVT fluid 8.1 14-1/8 ptsGenuine NISSAN CVT fluid
(NS-1) or exact equivalent
Power steering fluid 1.1 2 ptsType DEXRON
TMIII or equiva-
lent
Brake fluid DOT 4 (US FMVSS No. 116)
Multi-purpose grease NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant R-134a
Air conditioning system lubricantscompressor CR-14NISSAN A/C System Oil Type R
or exact equivalent
compressor CSV613NISSAN A/C System Oil Type S
or equivalent
*: For further details, see“SAE Viscosity Number”.
RECOMMENDED FLUIDS AND LUBRICANTS
MA-16
Page 2041 of 2267
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil grade: API SH or SJ/ACEA A2/96
Viscosity: See“RECOMMENDED FLUIDS AND LUB-
RICANTS”, MA-16.
Refill oil capacity (Approximate):
Unit:(Imp pts)
Drain and refill
With oil filter change2.9
Without oil filter change2.7
Dry engine (engine overhaul)3.0
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill oil capacity depends on oil temperature and
drain time. Use these specifications as a reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Start engine and check area around drain plug and oil filter
for oil leakage.
6. Run engine for a few minutes, then turn it off. After several
minutes, check oil level.
Changing Engine Oil Filter
1. Remove oil filter with Tool.
WARNING:
Be careful not to burn yourself, as the engine and the engine
oil are hot.
2. Clean the oil filter mounting surface on the cylinder block.
Coat the rubber seal of the new oil filter with engine oil.
SMA672C Oil filler cap
Oil filter
Drain plug
SMA390C Refill oil to this
“H”level.
Do not overfill.
SMA010
ENGINE MAINTENANCEQG
MA-24
Page 2047 of 2267
4. Remove cylinder block drain plug on water pipe and air relief
plug.
5. Check drained coolant for contaminants such as rust, corro-
sion or discoloration.
If contaminated, flush engine cooling system.
Refer to“FLUSHING COOLING SYSTEM”, MA-31.
—REFILLING ENGINE COOLANT—
6. Install lower radiator hose, reservoir tank and tighten cylinder
block drain plug securely.
Apply sealant to the thread of the cylinder block drain
plug.
:34-44N·m (3.5 - 4.5 kg-m, 25 - 33 ft-lb)
7. Fill up radiator with coolant at the speed of less than 3(2-5/8
Imp qt)/min.
If coolant spills from the air relief hole without bubbles, re-in-
stall the plug.
Air relief plug:
:10N·m (1.0 kg-m, 7 ft-lb)
Then pour coolant in again
Use genuine NISSAN Anti-Freeze Coolant or equivalent.
Refer to“RECOMMENDED FLUIDS AND LUBRICANTS”,
MA-16.
Coolant capacity (With reservoir tank):
Unit:(Imp qt)
SR20DE M/T6.6 (5-7/8)
CVT6.8 (6)
NMA048
.Remove
.Radiator filler cap
.SMA269c Drain plug
Remove
Oil level gauge guide
NMA005 Loosen
SMA182B Radiator
ENGINE MAINTENANCESR20DE
Changing Engine Coolant (Cont’d)
MA-30
Page 2051 of 2267
Changing Air Cleaner Filter
Viscous paper type
Unfasten clamps to change air cleaner filter.
The viscous paper type filter does not need cleaning.
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil grade: API SH or SJ/ACEA A2/96
Viscosity: See“RECOMMENDED FLUIDS AND LUBRI-
CANTS”, MA-16.
Refill oil capacity (Approximate):
Unit:(Imp pts)
Drain and refill
With oil filter change3.7 (6 - 1/2)
Without oil filter change3.5 (6 - 1/8)
Dry engine (engine overhaul)3.9 (6 - 7/8)
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill oil capacity depends on oil temperature and
drain time. Use these specifications as a reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Start engine and check area around drain plug and oil filter
for oil leakage.
6. Run engine for a few minutes, then turn it off. After several
minutes, check oil level.
NMA006
NMA039 Oil filter
SR20DE engine model
NDI021 Overfill
Normal range
Add
ENGINE MAINTENANCESR20DE
MA-34
Page 2062 of 2267
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil specification and viscosity:
ACEA B2-96 (CCMC-PD2)
See“RECOMMENDED FLUIDS AND LUBRICANTS”,
MA-16.
Oil capacity (Approximately):
Unit:(Imp pts)
Drain and refill
With oil filter change5.0
Without oil filter change4.5
Dry engine (engine overhaul)5.1
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill capacity depends on the oil temperature and
drain time. Use these specifications for reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Warm up engine, and check area around drain plug and oil
filter for oil leakage.
6. Stop engine.
7. Check oil level.
Changing Engine Oil Filter
1. Remove oil filter with Tool.
WARNING:
Be careful not to burn yourself, as engine and engine oil are
hot.
SMA418C Engine oil drain plug
.SMA411C Oil filter cap
Engine oil
level gauge
SMA822C Refill oil to this“H”
level.
Do not overfill.
SMA412C Engine oil
filter
ENGINE MAINTENANCECD20T
MA-45
Page 2066 of 2267
Check that oil is not leaking from transaxle or around it.
Remove speedometer pinion and check oil level distance“L”
as shown.
Oil level (“L”):
RS5F70A (QG16DE/QG18DE)
75.5 - 80.5 mm (2.97 - 3.17 in)
RS5F70A (SR20DE)
56.5 - 61.0 mm (2.22 - 2.60 in)
RS5F32A (CD20T)
57 - 62 mm (2.24 - 2.44 in)
Use genuine NISSAN XZ gear oil or exact equivalent.
Changing M/T Oil
Oil capacity (reference values only):
RS5F70A 3.0(5-1/4 Imp pts)
RS5F32A 3.6 - 3.8(6-3/8 - 6-3/4 Imp pts)
Drain plug:
:25-34N·m (2.5 - 3.5 kg-m, 18 - 25 ft-lb)
Use genuine NISSAN XZ gear oil or exact equivalent.
Checking CVT Fluid Level
1. Check for fluid leakage.
2. Check fluid level.
Fluid level should be check using“HOT”range on dipstick at
fluid temperatures of 50 to 80°C (122 to 176°F) after vehicle
has been driven approximately 10 minutes in urban areas
after engine is warmed up. But it can be checked at fluid
temperatures of 30 to 50°C (86 to 122°F) using“COLD”
range on dipstick for reference after engine is warmed up
and before driving. However, fluid level must be rechecked
using“HOT”range.
a. Park vehicle on level surface and set parking brake.
b. Start engine and then move selector lever through reach
gear range, ending in“P”.
NMA045
3.7 - 5.0
(0.38 - 0.51, 33 - 44)
Speedometer
pinion assembly
O-ring
Ruler
Transmission
case
:N·m
(kg-m, in-lb)
SMA145A Drain plug
SMA146B
UMA036 MAX
MIN
MINMAX
CHASSIS AND BODY MAINTENANCE
Checking M/T Oil (Cont’d)
MA-49
Page 2067 of 2267
c. Check fluid level with engine idling.
d. Remove dipstick and wipe it clean with lint-free paper.
e. Re-insert dipstick into charging pipe as far as it will go.
f. Remove dipstick and note reading. If level is at low side of
either range, add fluid.
Use genuine NISSAN CVT fluid (NS-1) or exact equivalent.
CAUTION
Do not overfill.
CAUTION:
Firmly fix the dipstick using a lip attached to the fluid charg-
ing pipe.
3. Check fluid condition.
Check fluid for contamination. If fluid is very dark, smells
burned or contains frictional material check operation of CVT.
Refer to section AT for checking operation of CVT.
Changing CVT Fluid
1. Warm up CVT fluid by driving the vehicle for 10 minutes.
2. Stop engine.
3. Drain CVT fluid from drain plug and refill with new CVT fluid.
Always refill same volume compared with drained fluid.
Oil capacity:
8.1(14 - 1/4 Imp pt)
Drain plug:
:23-27N·m (2.4 - 2.8 kg-m, 17 - 20 ft-lb)
Use genuine NISSAN CVT fluid (NS-1) or exact equivalent.
4. Run engine at idle speed for five minutes.
5. Jack up the front of the vehicle, and rotate front wheels by
selecting“D”and depressing accelerator pedal slowly until
50 km/h (2 or 3 times).
6. Check fluid level and condition. Refer to“Checking CVT Fluid
Level”. If fluid is still dirty, repeat step 2. throught 6.
SMA051D Stopper
(when fixing)
A/T fluid level
gauge
A/T fluid
charging pipeStopper
(when releasing)
SMA853B Check fluid for contamination.
SMA294C Drain
plug
CHASSIS AND BODY MAINTENANCE
Checking CVT Fluid Level (Cont’d)
MA-50
Page 2073 of 2267
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment Unit: mm (in) Tension adjustment* Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
LimitAfter
adjustmentLimitAfter
adjustment
Alternator
Without aircondi-
tioner compressor10.2
(0.402)6.5 - 7.0
(0.256 - 0.276)5.5 - 6.1
(0.217 - 0.240)
292
(29.8, 65.6)652 - 740
(66.5 - 75.5,
146.6 - 166.4)789 - 877
(80.5 - 89.7,
177.4 - 197.6)
With airconditioner
compressor8.1
(0.319)5.3 - 5.7
(0.209 - 0.224)4.5 - 5.0
(0.177 - 0.197)
Power steering
oil pump10.8
(0.425)6.6 - 7.5
(0.260 - 0.295)6.0 - 6.6
(0.236 - 0.260)196
(20.0, 44.1)495 - 583
(50.5 - 59.5,
111.3 - 131.1)603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied pushing force 98 N (10 kg, 22 lb)—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)Unit:(Imp pts)
With oil filter change 2.9 (5 - 1/8)
Without oil filter change 2.7 (4 - 3/4)
Coolant capacityUnit:(Imp pts)
With reservoir tank 6.1 (10 - 3/4)
Reservoir tank 0.8 (1 - 3/8)
Spark plug
Make CHAMPION NGK
Standard typeRC10YCC4
RC10YC4BKR5E-11
Hot typeRC12YCC4
RC12YC4BKR4E-11
Cold typeRC7YCC4
RC7YC4BKR6E-11
Plug gap mm (in) 1.0 - 1.1 (0.039 - 0.043)
SERVICE DATA AND SPECIFICATIONS (SDS)QG
MA-56
Page 2074 of 2267
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment Unit: mm (in) Tension adjustment* Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
LimitAfter adjust-
mentLimitAfter adjust-
ment
Alternator12-13
(0.47 - 0.51)8-9
(0.31 - 0.35)7-8
(0.28 - 0.31)264
(26.9, 59.3)493 - 583
(50.3 - 59.5,
110.8 - 131.1)11720 70J00 11720 70J05
603 - 691
(61.5 - 70.5,
135.6 - 155.3)652 - 740
(66.5 - 75.5,
146.6 - 166.4)
Air condi-
tioner com-
pressor9 (0.35)5.5 - 6.5
(0.217 -
0.256)4.5 - 5.5
(0.177 -
0.217)304
(31.0, 68.3)534 - 623
(54.5 - 63.5,
120.0 - 140.1)11920 9F500 11920 9F505
652 - 740
(66.5 - 75.5,
146.6 - 166.4)838 - 926
(85.5 - 94.5,
188 - 208)
Power steer-
ing oil pump12
(0.47)8-9
(0.31 - 0.35)7-8
(0.28 - 0.31)264
(26.9, 59.3)493 - 583
(50.3 - 59.5,
110.8 - 131.1)603 - 691
(61.5 - 70.5,
135.6 - 155.3)603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied push-
ing force98 N (10 kg, 22 lb)—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)Unit:(Imp pts)
With oil filter change 3.7 (6 - 1/2)
Without oil filter change 3.5 (6 - 1/8)
Coolant capacity (Refill capacity)
Unit:(Imp pts)
Engine SR20DE
With reservoir tankM/T 6.6 (11 - 5/8)
CVT 6.8 (12)
Reservoir tank 0.8 (1 - 3/8)
Spark plug
Make NGK
Ty p e
Standard BKR6EY-11
Hot—
Cold—
Plug gap mm (in) 1.0 - 1.1 (0.039 - 0.043)
Ignition leadUnit: kΩ/m
Ignition lead Resistance [at 25°C(77°F)]
No. 1 cylinder Approx 3.8
No. 2 cylinder Approx 3.5
No. 3 cylinder Approx 2.7
No. 4 cylinder Approx 2.4
For U.K. (Made by Bougicord) 4.48 - 6.72 kΩ(1.365 - 2.048
kΩ/ft) [at 25°C (77°F)]
SERVICE DATA AND SPECIFICATIONS (SDS)SR20DE
MA-57