tow NISSAN TEANA 2003 Workshop Manual

LT-176
LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCHPFP:25540
Removal and InstallationBKS001Q4
REMOVAL
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. While pressing pawls in direction as shown in the figure, pull
lighting and turn signal switch toward driver door and disconnect
from the base.
INSTALLATION
Installation is the reverse order of removal.
Switch Circuit InspectionBKS001Q5
Refer to LT- 1 8 5 , "Combination Switch Inspection" .
SKIB0899E

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

PERIODIC MAINTENANCE
MA-9
C
D
E
F
G
H
I
J
K
MA
B
MA

CHASSIS AND BODY MAINTENANCE
(Annual Mileage <30,000 Km [18,000 miles]/year)
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
NOTE:

(1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, inspect CVT fluid deterioration with
CONSULT-II every 90,000 km (54,000 miles), then change CVT fluid NS-2 if necessary. (Refer to CVT-46, "
Check CVT Fluid Dete-
rioration Date" .) And if CONSULT-II is not available, change (not just inspect) CVT fluid NS-2 every 90,000 km (54,000 miles).
Using transmission fluid other than Genuine Nissan CVT Fluid NS-2 will damage the CVT, which is not covered by the
warranty.

(2) Inspect once per year.

Maintenance items with “ ” should be performed more frequently according to “Maintenance Under Severe Driving
Conditions”. MAINTENANCE OPERATIONMAINTENANCE INTERVAL
Reference
page Perform either at number of kilometers
(miles) or months, whichever comes first.km x 1,000
(Miles x
1,000)
Months15
(9)
1230
(18)
2445
(27)
3660
(36)
4875
(45)
6090
(54)
72105
(63)
84120
(72)
96
Underhood and under vehicle
Head lamp aiming IIIIIIIILT- 6 0
, LT- 3 3
Brake system and fluid (For level & leaks) I I I I I I I IMA-40
Brake fluidRRRRMA-40
Brake booster vacuum hoses, connec-
tions & check valveIIIIBR-25
Power steering fluid & lines (For level &
leaks)IIIIIIIIMA-42
CVT fluid (For level & leaks)See
NOTE (1)IIIIMA-36
Automatic transaxle fluid (For level &
leaks)IIIIIIIIMA-35
Steering gear & linkage, axle & suspen-
sion parts, drive shaft & exhaust sys-
temIIIIMA-41, MA-
42 , MA-43 ,
MA-35
Wheel alignment (If necessary, rotate and
balance wheels)IIIIIIIIMA-38
Brake pads, rotors & other brake compo-
nentsIIIIIIIIMA-41
Foot brake & parking brake (For free
play, stroke & operation)IIIIIIIIBR-6, PB-3
Air conditioner filterRRRRAT C - 11 8
Body corrosionSee
NOTE (2)MA-45

MA-10
PERIODIC MAINTENANCE

MAINTENANCE UNDER SEVERE DRIVING CONDITIONS
(Annual Mileage <30,000 Km [18,000 miles]/year)
The maintenance intervals shown on the preceding pages are for normal operating conditions. If the vehicle is
mainly operated under severe driving conditions as shown below, more frequent maintenance must be per-
formed on the following items as shown in the table.
Severe driving conditions
A — Driving in dusty conditions
B — Repeatedly driving short distances
C — Towing a trailer or caravan
D — Extensive idling
E — Driving in extremely adverse weather conditions or in areas where ambient temperatures are either
extremely low or extremely high
F — Driving in high humidity or mountainous areas
G — Driving in areas using salt or other corrosive materials
H — Driving on rough and/or muddy roads or in the desert
I — Driving with frequent use of braking or in mountainous areas
J — For models without EURO-OBD system
Driving condition Maintenance itemMainte-
nance
operationMaintenance intervalReference
page
A.........Air cleaner filter ReplaceEvery 30,000 km (18,000 miles)
or 24 monthsMA-20
,
MA-30
ABCD......Engine oil & engine oil
filter ReplaceEvery 7,500 km (4,500 miles) or
6 monthsMA-20
, MA-
21 , MA-30 ,
MA-31
......... JHeated oxygen sensor InspectEvery 30,000 km (18,000 miles)
or 24 monthsEC-150
, EC-
143 , EC-496
, EC-486
.....F....Brake fluid ReplaceEvery 15,000 km (9,000 miles)
or 12 monthsMA-40
. . C . . . . H . . Automatic transaxle fluid ReplaceEvery 30,000 km (18,000 miles)
or 24 monthsMA-36
......GH..Steering gear & linkage,
axle & suspension parts,
propeller shaft, front
drive shafts & exhaust
systemInspectEvery 15,000 km (9,000 miles)
or 12 monthsMA-41
, MA-
42 , MA-43
,MA-35
A.C...GHI.Brake pads, rotors &
other brake componentsInspectEvery 7,500 km (4,500 miles) or
6 monthsMA-41, MA-
41 , MA-41
A.........Air conditioner filter ReplaceEvery 15,000 km (9,000 miles)
or 12monthsAT C - 11 8

MA-12
PERIODIC MAINTENANCE

CHASSIS AND BODY MAINTENANCE
(Annual Mileage >30,000 Km [18,000 miles]/year)
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
NOTE:

(1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, inspect CVT fluid deterioration with
CONSULT-II every 90,000 km (54,000 miles), then change CVT fluid NS-2 if necessary. (Refer to CVT-46, "
Check CVT Fluid Dete-
rioration Date" .) And if CONSULT-II is not available, change (not just inspect) CVT fluid NS-2 every 90,000 km (54,000 miles).
Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the
warranty.
(2) Inspect once per year.

Maintenance items with “ ” should be performed more frequently according to “Maintenance Under Severe Driving
Conditions”. MAINTENANCE OPERATIONMAINTENANCE INTERVAL
Reference
page Perform at number of kilometers
(miles) basis only.km x 1,000
(Miles x 1,000)15
(9)30
(18)45
(27)60
(36)75
(45)90
(54)105
(63)120
(72)
Underhood and under vehicle
Head lamp aiming I I I ILT- 6 0
, LT- 3 3
Brake system and fluid (For level &
leaks)IIIIMA-40
Brake fluidRRMA-40
Brake booster vacuum hoses, connec-
tions & check valveIIBR-25
Power steering fluid & lines (For level
& leaks)IIIIMA-42
CVT fluid (For level & leaks)See
NOTE (1)IIIIMA-36
Automatic transaxle fluid (For level &
leaks)IIIIMA-35
Steering gear & linkage, axle & sus-
pension parts, drive shafts & exhaust
systemIIMA-41, MA-
42 , MA-43 ,
MA-35
Wheel alignment (If necessary, rotate
and balance wheels)IIIIMA-38
Brake pads, rotors & other brake com-
ponentsIIIIMA-41
Foot brake & parking brake (For free
play, stroke & operation)IIIIBR-6, PB-3
Air conditioner filterRRRRAT C - 11 8
Body corrosionSee
NOTE (2)MA-45

PERIODIC MAINTENANCE
MA-13
C
D
E
F
G
H
I
J
K
MA
B
MA

MAINTENANCE UNDER SEVERE DRIVING CONDITIONS
(Annual Mileage >30,000 Km [18,000 miles]/year)
The maintenance intervals shown on the preceding pages are for normal operating conditions. If the vehicle is
mainly operated under severe driving conditions as shown below, more frequent maintenance must be per-
formed on the following items as shown in the table.
Severe driving conditions
A — Driving in dusty conditions
B — Repeatedly driving short distances
C — Towing a trailer or caravan
D — Extensive idling
E — Driving in extremely adverse weather conditions or in areas where ambient temperatures are either
extremely low or extremely high
F — Driving in high humidity or mountainous areas
G — Driving in areas using salt or other corrosive materials
H — Driving on rough and/or muddy roads or in the desert
I — Driving with frequent use of braking or in mountainous areas
J — For models without EURO-OBD system
Driving condition Maintenance itemMainte-
nance
operationMaintenance intervalReference
page
A.........Air cleaner filter Replace Every 30,000 km (18,000 miles) MA-30
, MA-
20
ABCD......Engine oil & engine
oil filter Replace Every 7,500 km (4,500 miles) MA-20
, MA-
21 , MA-30 ,
MA-31
.........JHeated oxygen sen-
sorInspect Every 60,000 km (36,000 miles)EC-150
, EC-
143 , EC-496
, EC-486
. . . . . F . . . . Brake fluid Replace Every 30,000 km (18,000 miles) MA-40
..C....H..Automatic transaxle
fluidReplace Every 60,000 km (36,000 miles) MA-36
......GH..Steering gear & link-
age, axle & suspen-
sion parts, propeller
shaft, front drive
shafts & exhaust sys-
temInspect Every 30,000 km (18,000 miles) MA-41
, MA-
42 , MA-43
,MA-35
A.C...GHI.Brake pads, rotors &
other brake compo-
nentsInspect Every 15,000 km (9,000 miles) MA-41, MA-
41 , MA-41
A.........Air conditioner filter Replace Every 15,000 km(9,000miles)AT C - 11 8

CHASSIS AND BODY MAINTENANCE
MA-45
C
D
E
F
G
H
I
J
K
MA
B
MA

Checking Body CorrosionBLS0009J
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PA N E L J O I N T
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.
PA N E L E D G E
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
PARTS CONTACT
Waist moulding, windshield moulding, bumper, etc.
PROTECTORS
Damage or condition of mudguard, fender protector, chipping protector, etc.
ANTI-CORROSION MATERIALS
Damage or separation of anti-corrosion materials under the body.
DRAIN HOLES
Condition of drain holes at door and side sill. When repairing corroded areas, refer to the Corrosion Repair
Manual.

PS-4
PRECAUTIONS

Precautions for Steering SystemBGS0003L

In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehi-
cle condition, and then check wheel alignment.

Observe the following precautions when disassembling.
–Before disassembly, thoroughly clean the outside of the unit.
–Disassembly should be done in a clean work area. It is important to prevent the internal parts from becom-
ing contaminated by dirt or other foreign matter.
–For easier and proper assembly, place disassembled parts in order on a parts rack.
–Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere
with their operation.
–Do not reuse non-reusable parts.
–Before assembling, apply the specified grease to the directed parts.

PS-28
POWER STEERING GEAR AND LINKAGE


Twist boot clamp as shown. Pay attention to relationship
between winding and twisting directions.

Twisted point of clamp is in the opposite side of adjusting
screw as shown in the figure (to prevent contact with other
parts).

Bend cut end of the wire toward rack axial as shown in the fig-
ure after twisting the wire 4 to 4.5 turns so that cut end does
not contact with boot.
CAUTION:
Keep gap from cylinder tube 5 mm (0.20 in) or more.
23. Install cylinder tubes to gear housing assembly.
24. Adjust inner socket to standard length L, and then tighten lock
nut to the specified torque. Refer to PS-20, "
COMPONENTS" .
Check length of inner socket L again after tightening lock nut .
Make sure that the length is the standard.
CAUTION:
Adjust toe-in after this procedure. Length achieved after
toe-in adjustment is not necessary the above value.
SGIA0164E
SGIA0361E
SGIA0260J
Inner socket length L : 127.3 mm (5.01 in)
SGIA0167E

POWER STEERING OIL PUMP
PS-33
C
D
E
F
H
I
J
K
L
MA
B
PS

ASSEMBLY
NOTE:
Secure oil pump in a vise if necessary.
CAUTION:
Use copper plates when securing in a vise.
1. Apply recommended grease to oil seal lips (1). Apply recom-
mended fluid to around oil seal, and then install oil seal to body
assembly.
2. Apply recommended fluid to drive shaft, and press drive shaft
into body assembly, then install snap ring.
3. Apply recommended fluid to O-ring, and then install O-ring into
body assembly.
4. Install side plate to body assembly.
5. Install dowel pin (3) into dowel pin hole (A), and then install cam
ring (2) pointing it's D
1 side toward the body assembly (1) side
as shown in the figure.

When installing cam ring, turn carved face with a letter E (B)
of it to rear cover.
CAUTION:
Do not confuse the assembling direction of cam ring. If
cam ring is installed facing the incorrect direction, it may
cause oil pump operation malfunction.
6. Install rotor to body assembly.
SGIA1150E
SGIA0422E
SGIA1166E