water pump NISSAN TEANA 2003 Workshop Manual

PRECAUTIONS
GI-5
C
D
E
F
G
H
I
J
K
L
MB
GI


Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.

If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.

Battery posts, terminals and related accessories contain lead
and lead compounds. Wash hands after handling.

To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.

Dispose of or recycle drained oil or the solvent used for cleaning
parts in an appropriate manner.

Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel
spray and possibly a fire.

Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.

Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new
ones.

Replace inner and outer races of tapered roller bearings and needle bearings as a set.

Arrange the disassembled parts in accordance with their assembled locations and sequence.

Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.

After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.

Use only the fluids and lubricants specified in this manual.

Use approved bonding agent, sealants or their equivalents when required.

Use hand tools, power tools (disassembly only) and recom-
mended special tools where specified for safe and efficient ser-
vice repairs.

When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leaks.

Before servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate cov-
ers.
Take caution that keys, buckles or buttons do not scratch paint.
SEF289H
SGI233
PBIC0190E
SGI234

IDX-8
ALPHABETICAL INDEX
Water control valve(QR20DE) .......................... CO-24
Water pump(QR20DE) ..................................... CO-22
Water pump(VQ23DE and VQ35DE) ............... CO-46
Water temperature gauge ..................................... DI-4
Wheel alignment (front) ..................................... FSU-5
Wheel balance ........................................ WT-4, MA-38
Wheel sensor (VDC) ....................................... BRC-86
WINDOW - Wiring diagram ............................... GW-23
Window antenna ................................................ AV-38
Window, door ...................................... GW-46, GW-50
Windshield ........................................................ GW-11
WIPER - Wiring diagram .................................. WW-11
Wiper, front ........................................................ WW-4
Wiring Diagram (Cell code) list .......................... PG-63
Wiring diagrams .................................................. GI-15
Wrist pin - See Piston pin inspection(QR20DE) EM-99

ENGINE OIL
LU-19
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
LU

ENGINE OILPFP:KLA92
InspectionBBS004WK
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range shown in the figure.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE

Check engine oil for white turbidity or heavy contamination.

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:

Oil pan

Oil pan drain plug

Oil pressure switch

Oil filter

Oil cooler (VQ35DE)

Water pump cover

Chain tensioner cover

Intake valve timing control cover and intake valve timing control solenoid valve

Mating surface between cylinder block and cylinder head

Mating surface between cylinder head and rocker cover

Mating surface between front timing chain case and rear timing chain case

Mating surface between rear timing chain case and cylinder block

Crankshaft oil seals (front and rear)
PBIC0249E

WW-38
FRONT WIPER AND WASHER SYSTEM

Removal and Installation of Washer TankBKS003WF
REMOVAL
: Vehicle front
1. Pull washer tank inlet out of washer tank.
2. Remove washer tank mounting bolt (A).
3. Remove fender protector RH on front side. Refer to EI-23, "
FENDER PROTECTOR" .
4. Disconnect front washer pump connector (1).
5. Remove washer tank mounting bolts (A).
6. Remove washer tube (2), and remove washer tank (3) from
vehicle.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
After installation, and water up to the upper level of the washer tank inlet, and check for water leaks.
SKIA6395E
PKID0314E
PKID0315E
Washer tank mounting bolts : 4.5 N·m (0.46 kg-m, 40 in-lb)