lock NISSAN TEANA 2003 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 2539 of 3502
POWER WINDOW SYSTEM
GW-45
C
D
E
F
G
H
J
K
L
MA
B
GW
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect front door switch (driver side) and BCM connector.
3. Check continuity between BCM connector M5 terminal 62 and
front door switch (driver side) connector B10 terminal 2.
4. Check continuity between BCM connector M5 terminal 62 and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR SWITCH
Check continuity between front door switch (driver side) terminal 2
and ground part of door switch.
OK or NG
OK >> GO TO 4.
NG >> Replace door switch.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM connector M5 terminal 62 and
ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace BCM.
Check Power Window Lock Switch BIS000ZO
1. CHECK POWER WINDOW LOCK SIGNAL
Exchanges for a normal power window main switch, and check operation.
Does power window lock operate?
YES >> Replace power window main switch.
NG >> Check condition of harness and connector.62 (SB) – 2 (SB) : Continuity should exist.
62 (SB) – Ground : Continuity should not exist.
PIIB1327E
TerminalCondition of door
switchContinuity
2Ground part of
door switchPushed No
Released Yes
PIIB1328E
62 (W) – Ground : Battery voltage
PIIB0630E
Page 2549 of 3502
![NISSAN TEANA 2003 Service Manual REAR WINDOW DEFOGGER
GW-55
C
D
E
F
G
H
J
K
L
MA
B
GW
through 15A fuse [No. 17, located in the fuse block (J/B)]
to BCM terminal 42.
With the ignition switch turned to ON or START position,
Power](/img/5/57392/w960_57392-2548.png "NISSAN TEANA 2003 Service Manual REAR WINDOW DEFOGGER
GW-55
C
D
E
F
G
H
J
K
L
MA
B
GW
through 15A fuse [No. 17, located in the fuse block (J/B)]
to BCM terminal 42.
With the ignition switch turned to ON or START position,
Power")
REAR WINDOW DEFOGGER
GW-55
C
D
E
F
G
H
J
K
L
MA
B
GW
through 15A fuse [No. 17, located in the fuse block (J/B)]
to BCM terminal 42.
With the ignition switch turned to ON or START position,
Power is supplied
through 10A fuse [No. 1, located in the fuse block (J/B)]
to BCM terminal 38.
through 10A fuse [No.12, located in the fuse block (J/B)]
to rear window defogger relay terminal 1.
through 10A fuse [No. 6, located in the fuse block (J/B)]
to A/C and AV switch terminal 7.
Ground is supplied
to BCM terminal 52
through grounds M71 and M72.
to A/C and AV switch terminal 13
through grounds M71 and M72.
to IPDM E/R terminals 38 and 60
through grounds E1 and E31.
When rear window defogger switch in A/C and AV switch is turned to ON,
Ground is supplied
to BCM terminal 9
through A/C and AV switch terminal 9
through A/C and AV switch terminal 13
through grounds M71 and M72.
Then rear window defogger switch is illuminated.
Then BCM recognizes that rear window defogger switch is turned to ON.
Then it sends rear window defogger switch signals to IPDM E/R and display unit (with out display control unit)
or display control unit (with display control unit) via DATA LINE (CAN H, CAN L).
When display unit or display control unit receives rear window defogger switch signals, indicator is displayed
on the screen.
When IPDM E/R receives rear window defogger switch signals,
Ground is supplied
to rear window defogger relay terminal 2
through IPDM E/R terminal 52
through IPDM E/R terminal 38 and 60
through grounds E1 and E31.
and then rear window defogger relay is activated.
When rear window defogger relay is turned ON,
Signals are transmitted,
through rear window defogger relay terminals 5
to rear window defogger terminal 1.
Rear window defogger terminal 2 is grounded through ground B253.
With power and ground supplied, rear window defogger filaments heat and defog the rear window.
through rear window defogger relay terminals 7
to door mirror defogger (driver side and passenger side) terminal 2.
Door mirror defogger (driver side and passenger side) terminal 3 are grounded through grounds M71 and
M72.
With power and ground supplied, door mirror defogger filaments heat and defog the mirror.
Page 2558 of 3502
GW-64
REAR WINDOW DEFOGGER
Check BCM Power Supply and Ground Circuit BIS00107
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, when perform the each trouble
diagnosis. Refer to BCS-14, "
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK FUSE
10A fuse [No.1, located in fuse block (J/B)]
15A fuse [No.17, located in fuse block (J/B)]
50A fusible link (letter M, located in the fuse and fusible link box).
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 52 and
ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open.
ConnectorTerminal
Condition of ignition
switchVoltage [V]
(Approx.)
(+) (-)
M338 (R)
GroundON
Battery voltage 42 (LG)
OFF
M4 55 (W/B)
PIIB1097E
52 (B) – Ground : Continuity should exist.
PIIB1099E
Page 2560 of 3502
GW-66
REAR WINDOW DEFOGGER
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M3 terminal 9 and
ground.
OK or NG
OK >> Replace A/C and AV switch.
NG >> Replace BCM.
Check Rear Window Defogger Power Supply Circuit BIS00109
1. CHECK FUSE
10A fuse [No.12, located in fuse block (J/B)]
20A fuse (No.75, located in the IPDM E/R)
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse, refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Remove rear window defogger relay.
2. Turn ignition switch ON.
3. Check voltage between rear window defogger relay connector
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between fuse block (J/B) and
rear window defogger relay.
3. CHECK REAR WINDOW DEFOGGER RELAY
Check continuity between rear window defogger terminals 3 and 5.
OK or NG
OK >> GO TO 4.
NG >> Replace rear window defogger relay.9 (GR/L) – Ground : Approx. 5V
PIIA6208E
1 (G) – Ground : Battery voltage
3 (L) – Ground : Battery voltage
PIIB1098E
Terminal Condition Continuity
3512V direct current supply
between terminals 1 and 2Ye s
No current supply No
SEC202B
Page 2562 of 3502
GW-68
REAR WINDOW DEFOGGER
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear window defogger connector
B252 terminal 2 and ground.
OK or NG
OK >> Check filament. Refer to GW-72, "Check Filament"
If filament is OK, check condition of harness and con-
nector.
If filament is NG, repair filament.
NG >> Repair or replace harness.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect rear window defogger relay connector and condenser connector.
3. Check continuity between rear window defogger relay connector
B203 terminal 5 and condenser connector B216 terminal 1.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK HARNESS CONTINUITY 2
1. Check continuity between condenser connector B216 terminal 1
and rear window defogger connector B251 terminal 1.
2. Check continuity between condenser connector B216 terminal 1
and ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace condenser.
Check Door Mirror Defogger Power Supply Circuit BIS0010B
1. CHECK FUSE
Check 10A fuse [No.32, located in fuse block (J/B)]
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location"
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT"
2 (B) − Ground : Continuity should exist.
PIIA4235E
5 (G) – 1 (G) : Continuity should exist.
PIIB1100E
1 (G) – 1 (B) : Continuity should exist.
1 (G) – Ground : Continuity should not exist.
PIIB1101E
Page 2576 of 3502
IDX-2
ALPHABETICAL INDEX
Numerics
3rd position switch ............................. AT-161
, AT-210
A
A/C air flow ...................................................... ATC-31
A/C component layout ..................................... ATC-20
A/C compressor clutch removal and installation ...........
ATC-136
A/C compressor mounting ............................. ATC-134
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-15
A/C control operation (auto A/C) ...................... ATC-29
A/C diagnostic work flow (auto A/C) ................ ATC-94
A/C evaporator ............................................... ATC-144
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure .......
ATC-131
A/C HFC134a (R134a) system service tools ... ATC-16
A/C HFC134a system service equipment precaution ...
ATC-12
A/C lubricant (R134a) ...................................... ATC-21
A/C lubrication oil ........................................... ATC-150
A/C operational check ...................................... ATC-54
A/C self-diagnoses (auto A/C) .......... ATC-46, ATC-94
A/C service data specification ........................ ATC-150
A/C system description (auto A/C) ................... ATC-24
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-14, MA-35
A/T fluid replacement ............................. AT-15, MA-36
A/T IND - Wiring diagram .................................... DI-48
A/T shift control system ................................... AT-213
A/T shift lock system ........................................ AT-216
A/T shift lock system - Wiring diagram ............ AT-217
A/T trouble diagnoses ........................................ AT-34
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-251,
EC-258
, EC-272, EC-631, EC-638, EC-652
Accelerator pedal released position learning .... EC-47,
EC-389
AFS ..................................................................... LT-75
AFS - Wiring diagram ......................................... LT-79
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-48
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(QR20DE) .................... EM-17
Air cleaner and air duct(VQ23DE and VQ35DE) ..........
EM-131
Air cleaner filter replacement(QR20DE) ........... MA-20
Air cleaner filter replacement(VQ23DE and VQ35DE) .
MA-30
Air cleaner filter(QR20DE) ................................ EM-17
Air cleaner filter(VQ23DE and VQ35DE) ........ EM-132
Air conditioner cut control .................... EC-25, EC-362
Air flow meter - See Mass air flow sensor ...... EC-124,
EC-466
Air mix. door motor ......................... ATC-66, ATC-124
Ambient sensor ............................... ATC-96, ATC-109
Angular tightening application(QR20DE) ............ EM-6
Angular tightening application(VQ23DE and VQ35DE)
EM-120
Antenna ............................................................. AV-38
APPS1 - Wiring diagram ................... EC-253, EC-633
APPS2 - Wiring diagram ................... EC-260, EC-640
APPS3 - Wiring diagram ................... EC-274, EC-654
ASC/BS - Wiring diagram ................................ EC-605
ASC/SW - Wiring diagram ............................... EC-597
ASCBOF - Wiring diagram ............................... EC-661
ASCD ............................................................... EC-363
ASCD (automatic speed control device) ........... ACS-2
ASCD brake switch ........................... EC-602, EC-660
ASCD indicator lamp ....................................... EC-667
ASCD steering switch ...................................... EC-595
ASCIND - Wiring diagram ................................ EC-668
AT indicator lamp ................................................ DI-48
Audio ........................................................ AV-4, AV-18
AUDIO - Wiring diagram .......................... AV-7, AV-21
Auto air conditioner - Wiring diagram ............. ATC-39
Auto amp ...................................................... ATC-108
Auto anti-dazzling inside mirror ....................... GW-80
Automatic amplifier ........... ATC-44, ATC-56, ATC-108
AV communication line .......................... AV-49, AV-73
Axle ................................................................... MA-42
B
BA/FTS - Wiring diagram ................................. AT-111
BACK/L - Wiring diagram ................................. LT-193
Back-up lamp ................................................... LT-193
Basic inspection .................................. EC-40, EC-381
Battery ................................................................. SC-4
BCM (Body control module) .............................. BCS-3
Blower motor ................................... ATC-72, ATC-115
Blower unit .................................................... ATC-113
Boring/horning cylinder block(QR20DE) ......... EM-104
Boring/horning cylinder block(VQ23DE and VQ35DE) .
EM-250
Brake fluid level ................................................ MA-40
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-41
Brake lines and cables inspection .................... MA-40
Brake pedal .......................................................... BR-6
Brake switch ......... EC-245, EC-602, EC-626, EC-660
BRK/SW - Wiring diagram ................ EC-247, EC-627
Bulb specifications ........................................... LT-261
Bumper, front ...................................................... EI-14
Bumper, rear ....................................................... EI-17
C
Camshaft inspection(QR20DE) ........................ EM-44
Camshaft inspection(VQ23DE and VQ35DE) EM-194
Camshaft position sensor (PHASE) .. EC-176, EC-524
Camshaft(QR20DE) .......................................... EM-41
Camshaft(VQ23DE and VQ35DE) .................. EM-192
CAN - Wiring diagram ......... EC-114, EC-459, AT-134,
CVT-54
Page 2577 of 3502
IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
CAN (Controller Area Network) . BL-23, BL-48, BL-77,
GW-56
, SE-16
CAN communication EC-113, EC-458, AT-27, CVT-19,
CVT-53
, BL-23, BL-48, BL-77, GW-56, SE-16, WW-9
Canister-See EVAP canister ............... EC-29, EC-369
CHARGE - Wiring diagram ................................ SC-28
Charging system ................................................ SC-27
Chassis and body maintenance ........................ MA-35
CHIME - Wiring diagram ..................................... DI-60
CIGAR - Wiring diagram .................................. WW-60
Cigarette lighter ............................................... WW-60
Circuit breaker ................................................... PG-16
Closed loop control .............................. EC-22, EC-359
Collision diagnosis ........................................... SRS-55
Combination meter ............................................... DI-4
COMM - Wiring diagram ........................ AV-49, AV-73
Component Location (auto A/C) ...................... ATC-36
Compression pressure(QR20DE) ...................... EM-65
Compression pressure(VQ23DE and VQ35DE) ...........
EM-210
Compressor clutch removal and installation .. ATC-136
Compressor special service tool ...................... ATC-15
Condenser ..................................................... ATC-142
Connecting rod bearing clearance(QR20DE) .. EM-105
Connecting rod bearing clearance(VQ23DE and
VQ35DE) ......................................................... EM-251
Connecting rod bushing clearance(QR20DE) . EM-101
Connecting rod bushing clearance(VQ23DE and
VQ35DE) ......................................................... EM-247
Connecting rod(QR20DE) ............................... EM-101
Connecting rod(VQ23DE and VQ35DE) ......... EM-247
CONSULT-II for engine ....................... EC-80, EC-425
CONSULT-II Reference value (CVT) .............. CVT-43
Control units (terminal arrangement) ................. PG-74
Control valve (CVT) ......................................... CVT-23
Controller Area Network (CAN) . BL-23, BL-48, BL-77,
GW-56
, SE-16
Converter housing installation ............ AT-244, AT-355
COOL/F - Wiring diagram .................. EC-222, EC-579
Coolant mixture ratio ......................................... MA-15
Coolant replacement(QR20DE) ......................... MA-16
Coolant replacementVQ35DE ........................... MA-25
Cooling circuit (engine)(QR20DE) ....................... CO-8
Cooling circuit (engine)(VQ32DE and VQ35DE) CO-32
Cooling fan control ........................................... EC-575
Cooling fan motor ............................................ EC-575
Cooling fan relay .............................................. EC-575
Cooling fan(QR20DE) ........................................ CO-20
Cooling fan(VQ23DE and VQ35DE) .................. CO-44
Cowl top ............................................................... EI-21
Cowl top cover ..................................................... EI-21
Crankcase ventilation system - See Positive crankcase
ventilation ............................................ EC-30
, EC-370
Crankshaft position sensor (POS) ..... EC-169, EC-517
Crankshaft(QR20DE) ...................................... EM-104
Crankshaft(VQ23DE and VQ35DE) ................ EM-251
Crash zone sensor .......................................... SRS-44
CVT air breather hose ................................... CVT-186
CVT control system ......................................... CVT-16
CVT cross-sectional view ................................ CVT-15
CVT Electrical parts location ............................ CVT-30
CVT fluid checking ................ CVT-13, CVT-32, MA-36
CVT Fluid Cooler ........................................... CVT-189
CVT fluid replacement ........................ CVT-14, MA-38
CVT fluid temparature sensor .......................... CVT-69
CVT hydraulic control system .......................... CVT-17
CVT indicator ...................................................... DI-52
CVT self-diagnoses ......................................... CVT-47
CVT shift lock system .................................... CVT-180
CVT trouble diagnoses .................................... CVT-24
CVTIND - Wiring diagram ................................... DI-52
Cylinder block boring(QR20DE) ..................... EM-104
Cylinder block(QR20DE) .................................. EM-81
Cylinder block(VQ23DE and VQ35DE) .......... EM-228
Cylinder head bolt tightening(QR20DE) ........... EM-68
Cylinder head bolt tightening(VQ23DE and VQ35DE) .
EM-213
Cylinder head(QR20DE) ................................... EM-65
Cylinder head(VQ23DE and VQ35DE) ........... EM-210
D
D/LOCK - Wiring diagram .................................. BL-25
Diagnosis sensor unit ..................................... SRS-47
Diagnostic trouble code (DTC) for OBD system EC-10,
EC-34
, EC-347, EC-375
Diagnostic trouble code (DTC) inspection priority chart
EC-58
, EC-400, CVT-24
Differentil side oil seal .................................... CVT-187
Display and amp.assembly ............... ATC-44, ATC-56
Display Control Unit ........................................... AV-61
Display Unit ........................................................ AV-41
Door glass ........................................... GW-46, GW-50
Door glass Fitting Adjustment(Front) ................ GW-49
Door glass Fitting Adjustment(Rear) ................. GW-53
Door lock .......................................................... BL-123
Door mirror .......................................... GW-74, GW-77
Door trim ............................................................. EI-35
Door, front ........................................... BL-119, GW-46
Door, rear ............................................ BL-119, GW-50
Drive belt inspection(QR20DE) ......................... MA-16
Drive belt inspection(VQ23DE and VQ35DE) ... MA-24
Drive belt(QR20DE) .......................................... EM-14
Drive belt(VQ23DE and VQ35DE) .................. EM-128
Drive shaft ......................................................... MA-43
Driver air bag .................................................. SRS-35
Dropping resistor (A/T) .................................... AT-132
Duct and grilles .............................................. ATC-126
E
ECM input/output signal ....................... EC-72
, EC-415
ECM power supply EC-106, EC-193, EC-451, EC-541
ECM/PW - Wiring diagram ................. EC-194, EC-542
ECTS - Wiring diagram ...................... EC-133, EC-476
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-197, EC-200,
EC-213
, EC-552, EC-555
Page 2579 of 3502
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Heated oxygen sensor 1 (bank 2) .... EC-486, EC-496,
EC-696
Heated oxygen sensor 1 heater ...................... EC-308
Heated oxygen sensor 1 heater (bank 1) ........ EC-706
Heated oxygen sensor 1 heater (bank 2) ........ EC-706
Heated oxygen sensor 2 .................................. EC-313
Heated oxygen sensor 2 (bank 1) ..... EC-714, EC-723
Heated oxygen sensor 2 (bank 2) ..... EC-714, EC-723
Heated oxygen sensor 2 heater ...................... EC-319
Heated seat ....................................................... SE-61
Heater and cooling unit (Heater core) ........... ATC-119
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-131
HFC134a (R134a) system service tools .......... ATC-16
HFC134a system service equipment precaution ..........
ATC-12
HLC - Wiring diagram ...................................... WW-43
HO2S1 - Wiring diaram ..................... EC-145, EC-152
Horn ................................................................. WW-62
HORN - Wiring diagram ................................... WW-62
How to erase DTC for OBD system ..... EC-35, EC-376
HSEAT - Wiring diagram ................................... SE-70
I
IATSEN - Wiring diagram .................. EC-325
, EC-731
Idle air volume learning ....................... EC-47, EC-389
Idle speed .............................. EC-40, EC-381, EC-387
Ignition coil ......................................... EC-329, EC-735
Ignition coil(QR20DE) ........................................ EM-31
Ignition coil(VQ23DE and VQ35DE) ................ EM-152
Ignition control system ....................... EC-329, EC-735
Ignition timing ........................ EC-40, EC-381, EC-387
IGNSYS - Wiring diagram .................. EC-330, EC-736
In vehicle sensor ............................. ATC-99, ATC-110
INF/D - Wring diagram ........................... AV-43, AV-65
INJECT - Wiring diagram ................... EC-290, EC-685
Injector ............................................... EC-289, EC-684
Input/Output signal of TCM .............................. CVT-19
Instrument panel .................................................. IP-10
INT/L - Wiring diagram ..................................... LT-217
Intake air temperature sensor ............ EC-324, EC-730
Intake door control linkage adjustment ............ ATC-71
Intake door motor ........................... ATC-69, ATC-117
Intake manifold collector(VQ23DE and VQ35DE) ........
EM-133
Intake manifold(QR20DE) ................................. EM-19
Intake manifold(VQ23DE and VQ35DE) ......... EM-138
Intake sensor ................................ ATC-105, ATC-112
Intake valve timing control ............................... EC-116
Intake valve timing control (Bank 1) ................ EC-461
Intake valve timing control (Bank 2) ................ EC-461
Intake valve timing control solenoid valve (Bank 1) ......
EC-545
Intake valve timing control solenoid valve (Bank 2) ......
EC-545
Interior ................................................................. EI-38
Interior lamp ........................................ LT-217, LT-219
IPDM (Intelligent power distribution module engine room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-119
IVCB1 - Wiring diagram ................................... EC-546
IVCB2 - Wiring diagram ................................... EC-548
K
Knock sensor (KS) ............................. EC-164
, EC-512
KS - Wiring diagram ........................... EC-165, EC-513
L
L/USSV - Wiring diagram ............................... CVT-148
LAN system circuit ........................................... ATC-59
LCD display ....................................................... AV-61
Line pressure and secondary pressure control CVT-20
Line pressure solenoid valve .......... CVT-97, CVT-102
Line pressure test (A/T) ..................................... AT-46
Liquid gasket application(QR20DE) ........... EM-6, LU-3
Liquid gasket application(VQ23DE and VQ35DE) ........
EM-120
, LU-15, CO-3, CO-27
Location of electrical units ................................. PG-67
Lock-up and select control ............................... CVT-21
Lock-up select solenoid valve ........................ CVT-147
LPSV - Wiring diagram ...................... AT-127, CVT-98
Lubricant (R134a) A/C ..................................... ATC-21
Lubricants ......................................................... MA-14
Lubrication circuit (engine)(QR20DE) .................. LU-5
Lubrication circuit (engine)(VQ23DE and VQ35DE) .....
LU-17
Lubrication oil A/C .......................................... ATC-150
M
MAFS - Wiring diagram ..................... EC-126
, EC-468
Magnet clutch ................................. ATC-78, ATC-136
MAIN - Wiring diagram ........ EC-106, EC-451, AT-158
Maintenance (engine)(VQ23DE and VQ35DE) MA-24
Malfunction indicator (MI) .................... EC-36, EC-377
Mass air flow sensor (MAFS) ............. EC-124, EC-466
Meter ..................................................................... DI-4
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ......... EC-344, EC-763
MIL/DL - Wiring diagram .................... EC-344, EC-763
Mirror, door ......................................... GW-74, GW-77
Mirror, out side .................................... GW-74, GW-77
MMSW - Wiring diagram ................................ CVT-114
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-123
Molding - See Exterior EI-25, EI-27, EI-28, EI-29, EI-30
Mud guard - See Exterior .................................... EI-24
Multiport fuel injection (MFI) system .... EC-21, EC-358
Multiport fuel injection precautions ....................... GI-6
N
NATS - Wiring diagram .................................... BL-143
NATS (Nissan anti-theft system) precautions ....... GI-3
NONDTC - Wiring diagram .............. AT-168, CVT-160
Page 2581 of 3502
IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
SECPSV - Wiring diagram ............................. CVT-109
SEN/PW - Wiring diagram ................. EC-234, EC-591
SESCVT - Wiring diagram ............................... CVT-80
SHIFT - Wiring diagram ................... AT-217, CVT-181
Shift control ...................................................... CVT-20
Shift control system ....................................... CVT-176
Shift lock system .............................................. AT-216
Shift schedule ................................. CVT-40, CVT-198
Side air bag (satellite) sensor .......................... SRS-45
Side curtain air bag .......................................... SRS-42
Side trim .............................................................. EI-38
SMJ (super multiple junction) ............................ PG-76
Spark plug replacement(QR20DE) .................... MA-22
Spark plug replacement(VQ23DE and VQ35DE) .........
MA-32
Spark plug(VQ23DE and VQ35DE) ................. EM-153
Specification value ............................... EC-95, EC-440
Speedometer ........................................................ DI-4
Spiral cable ...................................................... SRS-37
SROOF - Wiring diagram .................................. RF-13
SRS - See Supplemental Restraint System ...... SRS-5
SRS Trouble diagnoses ..................................... SRS-7
SSV/A - Wiring diagram ..................................... AT-91
SSV/B - Wiring diagram ..................................... AT-96
Stall Test .......................................................... CVT-32
Stall test (A/T) .................................................... AT-43
Standardized relay ............................................. PG-77
START - Wiring diagram ................................... SC-15
Starter ................................................................ SC-14
Starting system .................................................. SC-14
Steering gear and linkage inspection ................ MA-41
Steering linkage ................................................. PS-17
Steering wheel and column ..................... PS-9, PS-12
Step motor .................................... CVT-153, CVT-157
STM - Wiring diagram .................................... CVT-154
Stop lamp ......................................................... LT-190
Stop lamp switch .. EC-245, EC-602, EC-626, EC-660
STOP/L - Wiring diagram ................................. LT-190
STSIG - Wiring diagram .................................. CVT-57
Sun roof, electric ................................................ RF-10
Sunload sensor ............................. ATC-102, ATC-111
Sunroof .................................................. RF-10, RF-22
Sunshade ............................................................ EI-46
Supplemental Restraint System ........................ SRS-5
Suspension ........................................................ MA-42
Symbols and abbreviations ..................... GI-10, GI-23
Symptom matrix chart .......................... EC-60, EC-402
T
Tachometer .......................................................... DI-4
TCM circuit diagram ........................................ CVT-31
TCM function ................................................... CVT-18
TCM inspection table ........................... AT-64, CVT-40
TCV - Wiring diagram ........................ AT-106, CVT-90
Thermostat(QR20DE) ........................................ CO-24
Thermostat(VQ23DE and VQ35DE) .................. CO-50
Three way catalyst precautions ............................ GI-6
Three way catalyst(QR20DE) ............................ EM-23
Three way catalyst(VQ23DE and VQ35DE) ... EM-140
Throttle control motor ......................... EC-213, EC-568
Throttle control motor relay ................ EC-207, EC-562
Throttle position sensor (TPS) .......... EC-136, EC-157,
EC-229
, EC-231, EC-265, EC-479, EC-505, EC-586,
EC-588
, EC-645
Throttle valve closed position learning . EC-47, EC-389
Timing chain(QR20DE) ..................................... EM-53
Timing chain(VQ23DE and VQ35DE) ............. EM-173
Tire rotation ....................................................... MA-40
Torque converter installation AT-244, AT-355, CVT-196
Torque convertor clutch solenoid valve .......... CVT-89,
CVT-94
TPS1 - Wiring diagram ...................... EC-159, EC-507
TPS2 - Wiring diagram ...................... EC-138, EC-481
TPS3 - Wiring diagram ...................... EC-267, EC-647
Trouble diagnoses .............................................. GI-11
Trunk lid ........................................................... BL-131
Trunk lid opener - See Trunk lid ...................... BL-136
TURN - Wiring diagram .................................... LT-156
Turn signal lamp ............................................... LT-152
Two trip detection logic ........................ EC-33, EC-373
U
Unified meter and A/C amp. ............................... DI-27
V
Vacuum hose (brake system) ............................ BR-24
Vacuum hose drawing (Engine control) EC-69, EC-412
Valve clearance ................................................ EM-50
Valve clearance(VQ23DE and VQ35DE) ....... EM-202
Valve guide(QR20DE) ...................................... EM-73
Valve guide(VQ23DE and VQ35DE) EM-218, EM-219
Valve lifter(QR20DE) ........................................ EM-41
Valve lifter(VQ23DE and VQ35DE) ................ EM-196
Valve seat(QR20DE) ........................................ EM-75
Valve seat(VQ23DE and VQ35D) ................... EM-220
Valve seat(VQ23DE and VQ35DE) ................ EM-220
Valve spring(QR20DE) ..................................... EM-76
Valve spring(VQ23DE and VQ35DE) ............. EM-221
Variable induction air control system (VIAS) ... EC-753
VDC -Wiring diagram ...................................... BRC-49
Vehicle speed sensor (VSS) EC-183, EC-243, EC-622,
EC-624
, EC-762
VFD display ....................................................... AV-41
VIAS - Wiring diagram ..................................... EC-755
Viscosity number (SAE) .................................... MA-15
VSS A/T - Wiring diagram .................................. AT-82
VSSMTR - Wiring diagram ................................ AT-87
W
W/ANT - Wiring diagram .................................... AV-38
WARN - Wiring diagram ..................................... DI-37
Warning chime .................................................... DI-56
Warning lamps .................................................... DI-35
Washer, front ..................................................... WW-4
Page 2586 of 3502
IP-4
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SQUEAK AND RATTLE TROUBLE DIAGNOSESPFP:00000
Work FlowBIS00123
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to IP-8, "
Diagnostic Worksheet" . This information is necessary to duplicate the
conditions that exist when the noise occurs.
The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces=higher pitch noise/softer surfaces=lower pitch noises/edge to surface=chirping
Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.
Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.
Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842