lock NISSAN TEANA 2003 Service Manual

LT-230
INTERIOR ROOM LAMP

Terminals and Reference Values for BCMBKS001R8
Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
7 LG/R Door lock status signal OFF Door unlock sensorUNLOCK posi-
tionApprox. 0 V
Other
Approx. 8.5 - 9.0
12 R/LFront door switch (pas-
senger side) signalOFFFront door switch
(passenger side)ON (open) Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0
13 R/BRear door switch RH sig-
nalOFF Rear door switch RHON (open) Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0
37B/R
*1
BR*2Key switch signal OFFVehicle key is removed. Approx. 0 V
Vehicle key is inserted. Battery voltage
38 R Ignition switch (ON) ON — Battery voltage
39 L CAN−H— — —
40 P CAN−L— — —
42 Y/RBattery power
supplyOFF — Battery voltage
47 R/W Step lamp output signal OFFFront door switch (driver side)
or front door switch (passenger
side)ON
(open)Battery voltage
OFF
(close)Approx. 0 V
48 Y Room lamp output signalOFF
Interior
room lamp
switch:
DOOR
positionVehicle
key is
insertedAny
door
switchON
(open)Approx. 0 V
OFF
(closed)Battery voltage
—Vehicle
key is
removedAfter the
inserted key is
removedApprox. 0 V
Ignition key is
ONBattery voltage
PKIC4868J
PKIB4960J
PKIB4960J

LT-234
INTERIOR ROOM LAMP

Display Item List
NOTE:
1. Vehicle with Intelligent Key system displays this item.
2. Vehicle with remote keyless entry system displays this item.
ACTIVE TEST
Operation Procedure
1. Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching “OFF” deactivates the operation.
Display Item List
WORK SUPPORT (BATTERY SAVER)
Operation procedure
1. Select “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2. Select “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Select “ROOM LAMP BAT SAV SET” on “SELECT WORK ITEM” screen.
4. Touch “START”.
5. Touch “MODE1” or “MODE2” (ROOM LAMP TIMER SET)
6. Touch “CHANGE SETT”.
7. The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
8. Touch “END”.
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL “ON/OFF”Displays “Door open (ON)/Door closed (OFF) ” status, determined from rear door switch LH
signal.
LOCK STATUS “ON/OFF”Displays “Door unlocked (ON) /Door locked (OFF) status, determined from door unlock sen-
sor signal.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from central door lock
switch LOCK signal.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from central door lock switch UNLOCK
signal.
I − KEY LOCK
NOTE 1“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
I − KEY UNLOCK
NOTE 1“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
KEYLESS LOCK
NOTE2“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK
NOTE2“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
CONSULT-II screen
displayTest item Description
INT LAMPMap lamp, personal lamp and
ignition key hole illumination
operationMap lamp, personal lamp and ignition keyhole illumination is operated by
switching operation ON-OFF when map lamp switch and personal switch is in
DOOR position.

INTERIOR ROOM LAMP
LT-235
C
D
E
F
G
H
I
J
L
MA
B
LT

Display Item List
DATA MONITOR (BATTERY SAVER)
Operation Procedure
1. Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3. Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4. When “ALL SIGNALS” is selected, all the items will be monitored. When “SELECTION FROM MENU” is
selected, touch individual items to be monitored.
5. Touch “START”.
6. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Display Item List
NOTE:
1. Vehicle with Intelligent Key system displays this item.
2. Vehicle with remote keyless entry system displays this item.Item Description CONSULT-II
ROOM LAMP TIMER SET Interior room lamp battery saver timer setting can be changed.MODE 1: 30 min.
MODE 2: 60 min.
ROOM LAMP BAT SAV SETInterior room lamp battery saver control mode can be changed in this mode.
Select interior room lamp battery saver control mode between ON and OFF.ON/OFF
ALL SIGNALS Monitors all the items.
SELECTION FROM MENU Selects items and monitor them.
Monitor item Contents
IGN ON SW “ON/OFF”Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch sig-
nal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL “ON/OFF”Displays “Door open (ON)/Door closed (OFF) ” status, determined from rear door switch LH
signal.
LOCK STATUS “ON/OFF”Displays “Door unlocked (ON)/Door locked (OFF) status, determined from door unlock sen-
sor signal.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from central door lock
switch LOCK signal.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from central door lock switch UNLOCK
signal.
I − KEY LOCK
NOTE 1“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
I − KEY UNLOCK
NOTE 1“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
KEYLESS LOCK
NOTE2“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK
NOTE2“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.

LT-240
INTERIOR ROOM LAMP

Interior Room Lamps Illuminate But Timer Does Not OperateBKS002FW
1. CHECK EACH DOOR SWITCH
1. Select “BCM” on CONSULT-II. Select “INT LAMP” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
make sure switches listed below turn ON-OFF according to
switch operation.
OK or NG
OK >> GO TO 2.
NG >> Inspect malfunctioning switch system.
2. CHECK “SET I/L D-UNLCK INTCON” STATUS IN WORK SUPPORT
1. Select “BCM” on CONSULT-II. Select “INT LAMP” on “SELECT TEST ITEM” screen.
2. Select “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Select “SET I/L D-UNLCK INTCON” on “WORK SUPPORT” screen.
4. Touch “START” screen.
5. Check the current setting.
Is current setting
“ON”?
YES >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NO >> Change the setting.When front door (Driver side) is
closed: DOOR SW-DR OFF
When front door (passenger
side) is closed: DOOR SW-AS OFF
When rear door RH is closed : DOOR SW-RR OFF
When rear door LH is closed : DOOR SW-RL OFF
When front door (Driver side) is
locked: LOCK STATUS OFF
PKID0303E
PKID0203E

LT-242
INTERIOR ROOM LAMP

IGNITION KEYHOLE ILLUMINATION
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Remove screw, and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
Removal and InstallationBKS001RF
MAP LAMP
Removal
1. Insert a clip driver or suitable tool and disengage the pawl fit-
tings the map lamp.
2. Disconnect map lamp connector and remove map lamp.
Installation
Installation is the reverse order of removal.
STEP LAMP
Removal
1. Insert a clip driver or a suitable tool and remove lens and bulb
housing.
2. Disconnect step lamp connector.
Installation
Installation is the reverse order of removal.Ignition keyhole illumination : 14V - 1.4W
SKIA6362E
SKIA8659E
SKIB0900E

LT-244
ILLUMINATION

ILLUMINATIONPFP:27545
System DescriptionBKS001RI

BCM (Body Control Module) controls illumination lamp operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates illumination lamps according to
CAN communication signals from BCM.
OUTLINE
Power is supplied at all times

to ignition relay (located in IPDM E/R), from battery direct,

through 50A fusible link (letter M, located in fuse and fusible link box)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7,

through 15A fuse (No. 71, located in IPDM E/R)

to tail lamp relay (located in IPDM E/R) and

to CPU (central processing unit) in IPDM E/R

through 15A fuse (No. 78, located in IPDM E/R)

to CPU in IPDM E/R,

through 10A fuse [No. 19, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 21.
With the ignition switch in the ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 12, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 22,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52

to unified meter and A/C amp. terminals 29 and 30, and

to combination meter terminals 10, 11, and 12

through grounds M71 and M72,

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
ILLUMINATION OPERATION BY LIGHTING SWITCH
When the lighting switch is in 1ST position, BCM detects the LIGHTING SWITCH 1ST POSITION (ON) by
BCM combination switch reading function. And then, BCM sends position light request signal (ON) through
CAN communication and MR output signal.
When receiving position light request signal (ON), IPDM E/R turns ON tail lamp relay in IPDM E/R. And then
supplies power

through IPDM E/R terminal 22

to glove box lamp terminal 1

to A/T device illumination terminal 1 (with A/T)

to CVT device illumination terminal 1 (with CVT)

to rear sunshade front switch (illumination) terminal 5 (with rear sunshade)

LT-260
ILLUMINATION

Bulb ReplacementBKS001RO
ASHTRAY ILLUMINATION
1. Remove front side ashtray. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket left to release lock and remove it.
GLOVE BOX LAMP
1. Remove instrument passenger lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket left to release lock and remove it.
CIGARETTE LIGHTER ILLUMINATION
1. Remove ashtray. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws from rearward of cigarette lighter socket.
3. Open hooks and remove bulb socket.
CAUTION:
When replacing bulb, replace assembly together with illumination ring.Ashtray illumination : 13.5V - 1.2W
Glove box lamp : 14V - 1.4W
Cigarette lighter illumination : 12V - 1.4W

LU-4
[QR]
PREPARATION

PREPARATIONPFP:00002
Special Service ToolsBBS0059L
Commercial Service ToolsBBS0059M
Tool number
Tool nameDescription
ST25051001
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range: 2,452 kPa
(24.52 bar, 25 kg/cm
2 , 356 psi)
ST25052000
HoseAdapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrenchRemoving and installing oil filter
a: 64.3 mm (2.531 in)
WS39930000
Tube presserPressing the tube of liquid gasket
S-NT050
S-NT559
S-NT375
S-NT052
Tool nameDescription
Deep socketRemoving and installing oil pressure switch
a: 26 mm (1.02 in)
PBIC2072E

ENGINE OIL
LU-7
[QR]
C
D
E
F
G
H
I
J
K
L
MA
LU

ENGINE OILPFP:KLA92
InspectionBBS0059P
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range shown in the figure.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE

Check engine oil for white turbidity or heavy contamination.

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following area.

Oil pan

Oil pan drain plug

Oil pressure switch

Oil filter

Intake valve timing control cover and intake valve timing control solenoid valve

Front cover

Mating surface between cylinder block and lower cylinder block

Mating surface between cylinder block and cylinder head

Mating surface between cylinder head and rocker cover

Crankshaft oil seals (front and rear)
OIL PRESSURE CHECK
WARNING:

Be careful not to burn yourself, as engine oil may be hot.

Engine oil pressure check should be in “ Parking position”.
1. Check engine oil level. Refer to LU-7, "
ENGINE OIL LEVEL" .
2. Remove splash guard (RH).
3. Disconnect harness connector at oil pressure switch, and
remove oil pressure switch using deep socket (commercial ser-
vice tool).
PBIC0249E
PBIC2428E

ENGINE OIL
LU-19
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
LU

ENGINE OILPFP:KLA92
InspectionBBS004WK
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range shown in the figure.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE

Check engine oil for white turbidity or heavy contamination.

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:

Oil pan

Oil pan drain plug

Oil pressure switch

Oil filter

Oil cooler (VQ35DE)

Water pump cover

Chain tensioner cover

Intake valve timing control cover and intake valve timing control solenoid valve

Mating surface between cylinder block and cylinder head

Mating surface between cylinder head and rocker cover

Mating surface between front timing chain case and rear timing chain case

Mating surface between rear timing chain case and cylinder block

Crankshaft oil seals (front and rear)
PBIC0249E