trunk NISSAN TEANA 2003 Workshop Manual

TRUNK LID FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI

TRUNK LID FINISHERPFP:84810
Removal and InstallationBIS0011Q
REMOVAL
1. Fully open trunk lid.
2. Remove trunk lid finisher (inner). Refer to EI-35, "
DOOR FINISHER" .
3. Remove trunk lid finisher upper mounting nuts.
PIIA6259E
1. Nut 2. Seal 3. Stud bolt
4. Clip (C101) 5. Trunk lid finisher (upper) 6. Request switch harness connector
7. Trunk lid finisher (lower) 8. Clip 9. Grommet
10. Trunk lid 11. Double-faced adhesive tape
PIIA7080E

EI-34
TRUNK LID FINISHER

4. Remove trunk lid finisher upper mounting clips, and then pull out
trunk lid finisher upper toward rear of vehicle.
5. Disconnect request switch harness connector (only for models with intelligent key) after pulling out, then
remove trunk lid finisher upper.
6. Continuously, remove trunk lid finisher lower mounting clips the same as in step 4, and then remove trunk
lid finisher lower.
CAUTION:
After removal, visually inspect finisher, and if it is deformed, replace it with new molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Replace double-faced adhesive tape on back of finisher with a new tape if trunk lid finisher (lower)
is reused.

Remove double-faced adhesive tape remaining on body and back of finisher using double-faced
adhesive tape remover (SUMITOMO 3M Cleaner 30 or equivalent) when removing finisher (lower).

Install after cleaning adhesive parts of body side and back of finisher (lower).

Do not wash the vehicle within 24 hours after installing so as to keep adhesive.
PIIA7081E

DOOR FINISHER
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI

DOOR FINISHERPFP:80900
Removal and InstallationBIS0011R
1. Cap 2. Power window switch finisher (front) 3. Front door finisher
4. Front door inside seal 5. Door grip upper bracket 6. Door grip
7. Door grip finisher 8. Step lamp 9. Trunk & fuel lid opener switch
10. Seat memory switch 11. Seat memory switch finisher 12. Metal clip
13. Power window switch finisher (rear) 14. Rear door finisher
Clip Pawl Metal clip
PIIB8684E

EI-36
DOOR FINISHER

FRONT AND REAR DOOR FINISHER
Removal
1. Fully open door window.
2. Remove inside handle escutcheon cap.
3. Remove inside handle escutcheon screw.
4. Insert a remover tool A into power window switch finisher (front)
(1), lift up front end and disengage metal clip. Pull out finisher
toward front of vehicle.
CAUTION:
Lift up rear end of power window switch finisher (rear) and
disengage metal clips, and then pull out finisher toward
rear of vehicle.
5. Disconnect power window switch harness connector after pulling out, and then remove power window
switch finisher.
6. Remove power window switch screws.
7. Insert a clip clamp remover into clips on back of door trim, and
disengage clips.
CAUTION:
Insert a clip clamp remover into the part shown by the
arrow (between the clips and the body side panel). Remove
door trim.
8. Disconnect harness connector for trunk lid opener after disengaging.
9. Disconnect harness connector for seat memory switch (1) and
indirect lighting (2).
10. Disconnect harness connector for step lamp.
11. Pull up door trim and pull out toward vehicle inside, and then dis-
connect inside handle cable (3) and lock knob cable (2) from
inside handle (1).
PIIB8685E
SIIA0810E
PIIB8687E
PIIB8686E

DOOR FINISHER
EI-37
C
D
E
F
G
H
J
K
L
MA
B
EI

12. Remove door trim.
13. Remove the following parts after removing door trim.

Inside handle assembly

Trunk lid opener switch

Step lamp (front only)

Door grip

Front door inside handle

Door grip upper bracket

Seat memory switch (With automatic drive positioner)
Installation
Install in the reverse order of removal.
CAUTION:
When installing door trim, make sure that clips are securely fitted in panel holes on body, and then
press them in.

EI-44
REAR PARCEL SHELF FINISHER

REMOVAL
1. Remove rear seatback and rear seat cushion. Refer to SE-112, "REAR SEAT" .
2. Remove rear seat belt floor anchor bolt and rear seat belt shoulder anchor bolt. Refer to SB-5, "
Removal
and Installation of Rear Seat Belt" .
3. Disengage child anchor cover front pawls, and then pull out child
anchor cover (LH/RH center) toward front of vehicle.(Models
with rear window sunshade)
4. Remove rear kicking plate inner, rear seatback finisher, rear pillar finisher. Refer to EI-38, "
BODY SIDE
TRIM" .
5. Disconnect high-mounted stop lamp harness connector from
trunk room side. (Models without rear window sunshade)
6. Disconnect high-mounted stop lamp harness connector from
front side of rear parcel shelf finisher. (Models with rear window
sunshade)
7. Remove rear parcel shelf finisher mounting clip using a clip clamp remover.
8. Remove rear parcel shelf finisher while disengaging dual-lock fastener on back of rear parcel shelf fin-
isher. (Models with rear window sunshade)
9. Remove the following parts after removing rear parcel shelf finisher.

Rear speaker grille (for woofer)

High-mounted stop lamp
INSTALLATION
Install in the reverse order of removal.
7. Screw 8.Rear parcel shelf finisher (with sun-
shade)9. Child anchor cover (LH/RH center)
10. Rear window sunshade 11. Bolt 12. Locating pin
PIIA9530E
PIIA9531E
PIIA9535E

EI-58
TRUNK ROOM TRIM & TRUNK LID FINISHER

TRUNK ROOM TRIM & TRUNK LID FINISHERPFP:84920
Removal and Installation for Trunk Room TrimBIS0011Z
REMOVAL
1. Fully open trunk lid assembly.
2. Remove trunk lid weatherstrip.
3. Remove trunk floor carpet.
4. Remove trunk box assembly.
5. Remove trunk floor spacer (LH/RH).
1. Trunk lid weatherstrip 2. Trunk floor carpet 3. Trunk rear garnish (RH)
4. Clip (C205) (net hook) 5. Clip (C205) 6. Trunk rear finisher
7. Trunk wheelhouse finisher (RH) 8. Dual lock fastener 9. Trunk upper finisher (front)
10. Metal hook 11. Trunk lower finisher 12. Trunk floor spacer (RH)
13. Trunk box assembly 14. Trunk floor spacer (LH) 15. Trunk wheelhouse finisher (LH)
16. Trunk rear garnish (LH)
PIIA9623E

TRUNK ROOM TRIM & TRUNK LID FINISHER
EI-59
C
D
E
F
G
H
J
K
L
MA
B
EI

6. Remove trunk rear garnish mounting clips (net hook), and the
remove trunk rear garnish (LH/RH).
7. Remove trunk rear finisher mounting clips, and the remove trunk rear finisher.
8. Remove dual-lock fastener from back of trunk lower finisher, and then remove trunk lower finisher.
9. Disengage trunk upper finisher mounting clips and hooks, and remove trunk upper finisher.
10. Remove trunk wheelhouse finisher mounting clips, and the remove trunk wheelhouse finisher (LH/RH).
INSTALLATION
Install in the reverse order of removal.
REMOVAL AND INSTALLATION FOR TRUNK LID FINISHER INNER
Removal
1. Fully open trunk lid assembly.
2. Remove clips of trunk lid finisher inner.
3. Remove trunk lid finisher.
Installation
Install in the reverse order of removal.
NOTE:
Secure emergency handle to dual-lock fastener of trunk lid trim surface after installing.
PIIA6276E
PIIA6266E

EI-60
TRUNK ROOM TRIM & TRUNK LID FINISHER

HOW TO USE THIS MANUAL
GI-19
C
D
E
F
G
H
I
J
K
L
MB
GI

Harness Indication

Letter designations next to test meter probe indicate harness
(connector) wire color.

Connector numbers in a single circle M33 indicate harness con-
nectors.
Component Indication
Connector numbers in a double circle F211 indicate component connectors.
Switch Positions
Switches are shown in wiring diagrams as if the vehicle is in the “normal” condition.
A vehicle is in the “normal” condition when:

ignition switch is “OFF”,

doors, hood and trunk lid/back door are closed,

pedals are not depressed, and

parking brake is released.
AGI070
SGI860