key NISSAN TEANA 2008 Service Manual

DLK-62
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
PASSENGER SIDE : Description
INFOID:0000000003794851
Locks/unlocks the door with the signal from BCM.
PASSENGER SIDE : Component Function CheckINFOID:0000000003794852
1.CHECK FUNCTION
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-62, "
PASSENGER SIDE : Diagnosis Procedure".
PASSENGER SIDE : Diagnosis ProcedureINFOID:0000000003794853
1.CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (passenger side).
3. Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES >> Replace front door lock assembly (passenger side). Refer to DLK-222, "DOOR LOCK : Removal
and Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
REAR LH
REAR LH : DescriptionINFOID:0000000003794854
Locks/unlocks the door with the signal from BCM.
(+)
(–) ConditionVoltage (V)
(Approx.) Front door lock assembly (passenger side)
Connector Terminal
D481
GroundDoor lock and
unlock switchUNLOCK 0 → Battery voltage → 0
2LOCK0 → Battery voltage → 0
BCM Front door lock assembly (passenger side)
Continuity
Connector Terminal Connector Terminal
M1195
D481
Existed
82
BCM
GroundContinuity
Connector Terminal
M1195
Not existed
8

DOOR LOCK ACTUATOR
DLK-63
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR LH : Component Function CheckINFOID:0000000003794855
1.CHECK FUNCTION
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-63, "
REAR LH : Diagnosis Procedure".
REAR LH : Diagnosis ProcedureINFOID:0000000003794856
1.CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock assembly LH.
3. Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock assembly LH. Refer to DLK-202, "DOOR ASSEMBLY : Removal and
Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
REAR RH
REAR RH : DescriptionINFOID:0000000003794857
Locks/unlocks the door with the signal from BCM.
REAR RH : Component Function CheckINFOID:0000000003794858
1.CHECK FUNCTION
(+)
(–) ConditionVoltage (V)
(Approx.) Rear door lock assembly LH
Connector Terminal
D851
GroundDoor lock and
unlock switchLOCK 0 → Battery voltage → 0
2 UNLOCK 0 → Battery voltage → 0
BCM Rear door lock assembly LH
Continuity
Connector Terminal Connector Terminal
M1198
D851
Existed
10 2
BCM
GroundContinuity
Connector Terminal
M1198
Not existed
10

DLK-64
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-64, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000003794859
1.CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock assembly RH.
3. Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock assembly RH. Refer to DLK-208, "DOOR ASSEMBLY : Removal and
Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
(+)
(–)Condition of door lock and
unlock switchVoltage (V)
(Approx.) Rear door lock assembly RH
Connector Terminal
D1051
GroundUNLOCK 0 → Battery voltage → 0
2LOCK0 → Battery voltage → 0
BCM Rear door lock assembly RH
Continuity
Connector Terminal Connector Terminal
M1198
D1052
Existed
10 1
BCM
GroundContinuity
Connector Terminal
M1198
Not Existed
10

TRUNK LID OPENER ACTUATOR
DLK-65
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID OPENER ACTUATOR
DescriptionINFOID:0000000003794860
Trunk lid opener actuator open trunk lid from BCM.
Component Function CheckINFOID:0000000003794861
1.CHECK FUNCTION
1. Perform Active Test (“TRUNK/GLASS HATCH”) with CONSULT-III.
2. Touch “OPEN” and check that trunk lid opens.
Is the inspection result normal?
YES >> Trunk lid opener actuator is OK.
NO >> Refer to DLK-65, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794862
1.CHECK TRUNK LID OPENER INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly.
3. Check voltage between trunk lid lock assembly harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TRUNK LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and trunk lid lock assembly (trunk lid opener actuator)
harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK TRUNK LID OPENER ACTUATOR GROUND CIRCUIT
Check continuity between trunk lid lock assembly (trunk lid opener actuator) harness connector and ground.
(+)
(–) ConditionVoltage (V)
(Approx.) Trunk lid lock assembly
(trunk lid opener actuator)
Connector Terminal
T5 2 Ground Trunk lid opener switch is ON 0 → Battery voltage → 0
BCMTrunk lid lock assembly
(trunk lid opener actuator)
Continuity
Connector Terminal Connector Terminal
M120 23 T5 2 Existed
BCM
GroundContinuity
Connector Terminal
M120 23 Not existed

DLK-66
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID OPENER ACTUATOR
Is the inspection normal?
YES >> Replace trunk lid lock assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal and
Installation"
NO >> Repair or replace harness.
Trunk lid lock assembly
GroundContinuity
Connector Terminal
T5 3 Existed

REMOTE KEYLESS ENTRY RECEIVER
DLK-67
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
DescriptionINFOID:0000000003794867
Receives Intelligent Key operation and transmits to BCM.
Component Function CheckINFOID:0000000003794868
1.CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver (“RKE OPE COUN1”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Remote keyless entry receiver is OK.
NO >> Refer to DLK-67, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794869
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between remote keyless entry receiver harness connector and ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1. Disconnect BCM connector and remote keyless entry receiver connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item Condition
RKE OPE COUN1 Checks whether value changes when operating Intelligent Key.
(+)
(–) ConditionSignal
(Reference value) Remote keyless entry receiver
Connector Terminal
M78 2 GroundWaiting
(All doors closed)
When signal is received
(All doors closed)
JMKIA0064GB
JMKIA0065GB
BCM Remote keyless entry receiver
Continuity
Connector Terminal Connector Terminal
M122 83 M78 2 Existed

DLK-68
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Repair or replace harness.
3.CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
Check signal between remote keyless entry receiver harness connector and ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
1. Disconnect BCM connector and remote keyless entry receiver.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1. Disconnect BCM connector and remote keyless entry receiver.
2. Check continuity between BCM connector and remote keyless entry receiver connector.
3. Check continuity between BCM harness connector and ground.
BCM
GroundContinuity
Connector Terminal
M122 83 Not existed
(+)
(–)Signal
(Reference value) Remote keyless entry receiver
Connector Terminal
M78 4 Ground
JMKIA0064GB
BCM Remote keyless entry receiver
Continuity
Connector Terminal Connector Terminal
M122 103 M78 4 Existed
BCM
GroundContinuity
Connector Terminal
M122 103 Not existed
BCM Remote keyless entry receiver
Continuity
Connector Terminal Connector Terminal
M123 137 M78 1 Existed

REMOTE KEYLESS ENTRY RECEIVER
DLK-69
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT 2
1. Connect remote keyless entry receiver connector.
2. Check continuity between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES >> Replace remote keyless entry receiver. Refer to DLK-244, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-78, "
Removal and Installation".
BCM
GroundContinuity
Connector Terminal
M122 137 Not existed
Remote keyless entry receiver
GroundContinuity
Connector Terminal
M78 1 Existed

DLK-70
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID OPENER SWITCH
TRUNK LID OPENER SWITCH
DescriptionINFOID:0000000003794870
Output trunk lid open signal to BCM.
Component Function CheckINFOID:0000000003794871
1.CHECK FUNCTION
Check trunk lid opener switch (“TR/BD OPEN SW”) in “Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Trunk lid opener switch is OK.
NO >> Refer to DLK-70, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794872
1.CHECK TRUNK LID OPENER INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect trunk lid opener switch connector.
3. Check signal between trunk lid opener switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TRUNK LID OPENER SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and trunk lid opener switch harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
Monitor item Condition
TR/BD OPEN SWTrunk lid opener switch is pressed: ON
Trunk lid opener switch is released: OFF
(+)
(–)Signal
(Reference value) Trunk lid opener switch
Connector Terminal
M25 1 Ground
JPMIA0011GB
BCM Trunk lid opener switch
Continuity
Connector Terminal Connector Terminal
M121 67 M25 1 Existed
BCM
GroundContinuity
Connector Terminal
M121 67 Not existed

TRUNK LID OPENER SWITCH
DLK-71
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
NO >> Repair or replace harness.
3.CHECK TRUNK LID OPENER SWITCH GROUND CIRCUIT
Check continuity between trunk lid opener switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK TRUNK LID OPENER SWITCH
Refer to DLK-71, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace trunk lid opener switch. Refer to DLK-243, "
Removal and Installation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003794873
1.CHECK TRUNK LID OPENER SWITCH
1. Turn ignition switch OFF.
2. Disconnect trunk lid opener switch connector.
3. Check continuity between trunk lid opener switch terminal.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace trunk lid opener switch. Refer to DLK-243, "
Removal and Installation".
Trunk lid opener switch
GroundContinuity
Connector Terminal
M25 2 Existed
Trunk lid opener switch
Condition Continuity
Te r m i n a l
12ON (press and hold) Existed
OFF (release) Not existed