belt NISSAN TEANA 2008 Service Manual

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
SR-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
5. Connect red clip of deployment tool (SST: KV99106400) (A) to
battery positive terminal and black clip to negative terminal (B).
6. The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
7. Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, will illuminate and
the air bag module (1) will deploy.
CAUTION:
When deploying the front side air bag module, stand at
least 5.0 m (16.4 ft) away from the air bag module.
Front Seat Belt Pre-Tensioner (Outside of Vehicle)
1. Firmly grip pre-tensioner (1) in a vise (A) and cut off the web-
bing.
2. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99110500) (B) yellow connector to
front seat belt pre-tensioner (1).
3. Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal (C).
4. The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
5. Press the button on the deployment tool. The left side lamp on
the tool, marked “seat belt pre-tensioner connector voltage”, will
illuminate and the seat belt pre-tensioner (1) will deploy.
CAUTION:
When deploying the front seat belt pre-tensioner, stand at
least 5.0 m(16.4 ft) away from the seat belt pre-tensioner.
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module and seat belt pre-tensioner are very hot. Before disposing of air bag module and
seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag
before disposal.
CAUTION:
 Never apply water to a deployed air bag module or seat belt
pre-tensioner.
 Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner.
 No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
 Never disassemble air bag module and seat belt pre-ten-
sioner.
 Air bag module and seat belt pre-tensioner cannot be reused.
 Wash your hands clean after the work is complete.
JMHIA0285ZZ
JMHIA0068ZZ
JMHIA0214ZZ
SBF276H

SRC-4
SRS AIR BAG WARNING LAMP DOES NOT
TURN OFF .......................................................
145
Diagnosis Procedure .............................................145
SRS AIR BAG WARNING LAMP DOES NOT
TURN ON .........................................................
146
Diagnosis Procedure .............................................146
PRECAUTION ...........................................147
PRECAUTIONS ................................................147
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
147
Service ..................................................................147

SRS AIR BAG SYSTEM
SRC-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
FUNCTION DIAGNOSIS
SRS AIR BAG SYSTEM
System DiagramINFOID:0000000003813930
System DescriptionINFOID:0000000003813931
THIS SRS AIR BAG SYSTEM HAS THE FOLLOWING FUNCTIONS
1. Detects crash and supply the energy for deploying air bag and seat belt pre-tensioner.
2. Detects electrical trouble in air bag system and seat belt pre-tensioner system, records trouble code, and
blinking air bag warning lamp.
JMHIA0600GB

SRC-8
< FUNCTION DIAGNOSIS >
SRS AIR BAG SYSTEM
3. Detects and records the deployment of air bag and seat belt pre-tensioner, and turns on air bag warning
lamp.
4. Indicates malfunctioning portion with blinking times of air bag warning lamp in diagnosis mode.
5. Indicates the malfunctioning record by CONSULT-III.
Component Parts LocationINFOID:0000000003813932
Component DescriptionINFOID:0000000003813933
 Air bag diagnosis sensor units are prepared for operation while the ignition switch is in the ON or START
position.
 The operation of Supplemental Restraint System is different from collision modes application. For example,
the driver air bag module and front passenger air bag module are activated in a frontal collision but not in a
side collision.
 SRS configurations which are activated for some collision modes are as follows.
1. Front passenger air bag module M62 2. Driver air bag module M350 3. Conbination switch (Spiral cable)
M32
4. Air bag diagnosis sensor unit B14,
B228, M595. LH/RH satellite sensor
LH B37
 RH B2116. Front LH/RH seat belt pre-tensioner
LH B36
RH B213
7. Front LH/RH side air bag module
LH B16
 RH B2128. Crash zone sensor E313 9. Combination meter (Air bag warning
lamp) M34
10. LH/RH side curtain air bag module
LH B72
 RH B256
JMHIA0599ZZ
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module. Refer to SRC-122, "
Diagnosis
Procedure"×——
Front passenger air bag module. Refer to SRC-122,
"Diagnosis Procedure"×——

SRS AIR BAG SYSTEM
SRC-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
×: Application, —: No application
Front LH seat belt pre-tensioner. Refer to SRC-122,
"Diagnosis Procedure"×——
Front RH seat belt pre-tensioner. Refer to SRC-122,
"Diagnosis Procedure"×——
Front LH side air bag module. Refer toSRC-124, "
Di-
agnosis Procedure" —×—
Front RH side air bag module. Refer to SRC-124, "
Di-
agnosis Procedure"——×
LH side curtain air bag module. Refer to SRC-124,
"Diagnosis Procedure"—×—
RH side curtain air bag module. Refer to SRC-124,
"Diagnosis Procedure"——× SRS configuration Frontal collision Left side collision Right side collision

SRC-12
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (AIRBAG)
Air bag warning lamp examples (User mode)
DIAGNOSTIC PROCEDURE (DIAGNOSIS MODE)
1. Turn the ignition switch ON, and check that the air bag warning lamp blinks.
2. There are 2 blinking patterns for the air bag warning lamp. One is a 3-second blink followed by a 0.5- sec-
ond blink repeat. The other is two 1.5-second blinks followed by a 0.5-second blink repeat.
Air bag warning lamp operation -User mode SRS condition Reference item
 No malfunction is detected
 No further action is necessary—
The system is malfunctioning and
needs to be repaired as indicatedGo to SRC-10, "
Air Bag Warning
Lamp Diagnosis"
 Air bag is deployed
 Seat belt pre-tensioner is deployedGo to SRC-122, "Diagnosis Proce-
dure" or SRC-124, "Diagnosis Pro-
cedure"
 Air bag diagnosis sensor unit is mal-
functioning
 Air bag power supply circuit is mal-
functioning
 Air bag warning lamp circuit is mal-
functioningGo to SRC-145, "
Diagnosis Proce-
dure"
 Air bag diagnosis sensor unit is mal-
functioning
 Air bag warning lamp circuit is mal-
functioningGo to SRC-146, "
Diagnosis Proce-
dure"
SHIA0011E
SHIA0012E
SHIA0013E
SHIA0014E

DIAGNOSIS SYSTEM (AIRBAG)
SRC-13
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P An Example of a 3-second Blink Followed by a 0.5-second Blink Repeat
a through b are repeated.
b: Seven 0.5-second blinks indicate that the air bag diagnosis sensor unit circuit is malfunctioning.
Number of 0.5-second Blinks After a 3-second Blink Indicates Malfunctioning Items
JMHIA0640GB
Number of 0.5-second blinks Malfunctioning items Blinking pattern
0 Self-diagnosis result is not deleted —
1 Front LH seat belt pre-tensionerRefer to the following
SRC-60, "
DTC Logic"
SRC-62, "DTC Logic"
SRC-64, "DTC Logic"
SRC-66, "DTC Logic"
2 Driver air bag moduleRefer to the following
SRC-32, "
DTC Logic"
SRC-34, "DTC Logic"
SRC-36, "DTC Logic"
SRC-38, "DTC Logic"
3 Front RH seat belt pre-tensionerRefer to the following
SRC-52, "
DTC Logic"
SRC-54, "DTC Logic"
SRC-56, "DTC Logic"
SRC-58, "DTC Logic"
6 Crash zone sensorRefer to the following
SRC-24, "DTC Logic"
SRC-26, "DTC Logic"
SRC-28, "DTC Logic"
7 Air bag diagnosis sensor unitRefer to the following
SRC-16, "
DTC Logic"
SRC-18, "DTC Logic"
SRC-20, "DTC Logic"
SRC-22, "DTC Logic"
SRC-30, "DTC Logic"
SRC-40, "DTC Logic"
SRC-50, "DTC Logic"
SRC-70, "DTC Logic"
SRC-80, "DTC Logic"
SRC-98, "DTC Logic"
SRC-120, "DTC Logic"
SRC-68, "DTC Logic"
SRC-118, "DTC Logic"
SRC-130, "DTC Logic"

SRC-16
< COMPONENT DIAGNOSIS >
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
COMPONENT DIAGNOSIS
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
DescriptionINFOID:0000000003813936
Check the whole SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
in the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC LogicINFOID:0000000003813937
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-16, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003813938
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1001
B1002
B1003
B1004
B1005CONTROL UNIT Air bag diagnosis sensor unit is mal-
functioning or out of the specification Malfunction in air bag diagnosis sen-
sor unit
 Configuration in air bag diagnosis
sensor unit dose not match to the ve-
hicles specification

SRC-18
< COMPONENT DIAGNOSIS >
B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT
B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT
DescriptionINFOID:0000000003813939
Check the whole SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
in the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC LogicINFOID:0000000003813940
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-18, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003813941
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1006
B1007
B1008
B1009
B1010CONTROL UNIT Air bag diagnosis sensor unit is mal-
functioning or out of the specification Malfunction in air bag diagnosis sen-
sor unit
 Configuration in air bag diagnosis
sensor unit dose not match to the ve-
hicles specification

SRC-20
< COMPONENT DIAGNOSIS >
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
DescriptionINFOID:0000000003813942
Check the whole SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
in the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC LogicINFOID:0000000003813943
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-20, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003813944
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1011
B1012
B1013
B1014
B1015CONTROL UNIT Air bag diagnosis sensor unit is mal-
functioning or out of the specification Malfunction in air bag diagnosis sen-
sor unit
 Configuration in air bag diagnosis
sensor unit dose not match to the ve-
hicles specification