light NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 2206 of 5121
![NISSAN TEANA 2008 Service Manual HEADLAMP AIMING ADJUSTMENT
EXL-177
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center NISSAN TEANA 2008 Service Manual HEADLAMP AIMING ADJUSTMENT
EXL-177
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center](/img/5/57391/w960_57391-2205.png)
HEADLAMP AIMING ADJUSTMENT
EXL-177
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)Lateral direction (X)
(Right and left side from headlamp centerline)
Highest light axis 106 (4.17)
0-100 (3.94) Target light axis 120 (4.72)
Lowest light axis 164 (6.46)
Page 2207 of 5121
![NISSAN TEANA 2008 Service Manual EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, re NISSAN TEANA 2008 Service Manual EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, re](/img/5/57391/w960_57391-2206.png)
EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
Adjust the tire pressure to the specification.
Fill with fuel, engine coolant and each oil.
Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Turn the aiming adjusting screw for adjustment.
For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment ProcedureINFOID:0000000003773618
1. Place the screen.
NOTE:
Stop the vehicle facing the wall.
Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA1086ZZ
JPLIA0008ZZ
Page 2215 of 5121
![NISSAN TEANA 2008 Service Manual EXL-186
< ON-VEHICLE REPAIR >[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded ViewINFOID:0000000003773628
Removal and InstallationINFOID:0000000003773629
Lighting & tu NISSAN TEANA 2008 Service Manual EXL-186
< ON-VEHICLE REPAIR >[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded ViewINFOID:0000000003773628
Removal and InstallationINFOID:0000000003773629
Lighting & tu](/img/5/57391/w960_57391-2214.png)
EXL-186
< ON-VEHICLE REPAIR >[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded ViewINFOID:0000000003773628
Removal and InstallationINFOID:0000000003773629
Lighting & turn signal switch is integrated in the combination switch. Refer to BCS-79, "Exploded View".
Page 2229 of 5121
![NISSAN TEANA 2008 Service Manual EXL-200
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
HEADLAMP SYSTEM
FUNCTION DIAGNOSIS
HEADLAMP SYSTEM
System DiagramINFOID:0000000003773647
System DescriptionINFOID:0000000003773648
OUTLINE
Headlamp is cont NISSAN TEANA 2008 Service Manual EXL-200
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
HEADLAMP SYSTEM
FUNCTION DIAGNOSIS
HEADLAMP SYSTEM
System DiagramINFOID:0000000003773647
System DescriptionINFOID:0000000003773648
OUTLINE
Headlamp is cont](/img/5/57391/w960_57391-2228.png)
EXL-200
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
HEADLAMP SYSTEM
FUNCTION DIAGNOSIS
HEADLAMP SYSTEM
System DiagramINFOID:0000000003773647
System DescriptionINFOID:0000000003773648
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
BCM detects the combination switch condition with the combination switch reading function.
BCM transmits the low beam request signal to IPDM E/R with CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light function ON judgment)
IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
BCM transmits the high beam request signal to IPDM E/R and the combination meter with CAN communica-
tion according to the headlamp (HI) ON condition.
Headlamp (HI) ON condition- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
JPLIA0167GB
Page 2230 of 5121
![NISSAN TEANA 2008 Service Manual HEADLAMP SYSTEM
EXL-201
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003773649
Component DescriptionINFOID:0000000003773650
1. Headlamp ( NISSAN TEANA 2008 Service Manual HEADLAMP SYSTEM
EXL-201
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003773649
Component DescriptionINFOID:0000000003773650
1. Headlamp (](/img/5/57391/w960_57391-2229.png)
HEADLAMP SYSTEM
EXL-201
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003773649
Component DescriptionINFOID:0000000003773650
1. Headlamp (HI) 2. Headlamp (LO) 3. Combination switch
4. IPDM E/R 5. BCM 6. High beam indicator lamp
A. Engine room (LH) B. Behind the combination meter C. On the combination meter
J P L I A 111 8 Z Z
Part Description
BCM Detects each switch condition by the combination switch reading function.
Judges that the headlamp is turned ON according to the vehicle condition.
- Requests the headlamp relay (HI/LO) ON to IPDM E/R (with CAN communication).
- Requests the high beam indicator lamp ON to the combination meter (with CAN
communication).
IPDM E/RControls the integrated relay, and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)Refer to BCS-8, "
System Diagram".
Combination meter
(High beam indicator lamp)Turns the high beam indicator lamp ON according to the request from BCM (with CAN
communication).
Page 2231 of 5121
![NISSAN TEANA 2008 Service Manual EXL-202
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
AUTO LIGHT SYSTEM
AUTO LIGHT SYSTEM
System DiagramINFOID:0000000003894281
System DescriptionINFOID:0000000003894282
OUTLINE
Auto light system is control NISSAN TEANA 2008 Service Manual EXL-202
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
AUTO LIGHT SYSTEM
AUTO LIGHT SYSTEM
System DiagramINFOID:0000000003894281
System DescriptionINFOID:0000000003894282
OUTLINE
Auto light system is control](/img/5/57391/w960_57391-2230.png)
EXL-202
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
AUTO LIGHT SYSTEM
AUTO LIGHT SYSTEM
System DiagramINFOID:0000000003894281
System DescriptionINFOID:0000000003894282
OUTLINE
Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM- Combination switch reading function
- Headlamp control function
- Auto light function
- Delay timer function
Control by IPDM E/R- Relay control function
Auto light system has the auto light function and the delay timer function.
- Auto light function turns the exterior lamps* and each illumination ON/OFF automatically according to the
outside brightness.
- When auto light system turns the exterior lamps ON with the ignition switch OFF, delay timer function turns
the exterior lamps OFF depending on the vehicle condition with the auto light function after a certain period
of time.
*: Headlamp (LO/HI), parking lamp, tail lamp and front fog lamp (Headlamp HI and front fog lamp depend on
the combination switch condition.)
AUTO LIGHT FUNCTION
BCM detects the combination switch condition with the combination switch reading function.
BCM supplies voltage to optical sensor when the ignition switch is turned ON or ACC.
Optical sensor converts outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
BCM judges outside brightness from the optical sensor signal and judges ON/OFF condition of the exterior
lamp and each illumination according to the outside brightness.
BCM transmits each request signal to IPDM E/R with CAN communication according to ON/OFF condition
by the auto light function.
NOTE:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT-III. Refer
to EXL-215, "
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".
DELAY TIMER FUNCTION
BCM turns the exterior lamp OFF depending on the vehicle condition with the auto light function when the igni-
tion switch is turned OFF.
Turns the exterior lamp OFF 5 minutes after detecting that any door opens (Door switch ON).
Turns the exterior lamp OFF a certain period of time* after closing all doors (Door switch ON→OFF).
JPLIA0804GB
Page 2232 of 5121
![NISSAN TEANA 2008 Service Manual AUTO LIGHT SYSTEM
EXL-203
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Turns the exterior lamp OFF with the ignition switch ACC or the light switch OFF.
*: The preset time i NISSAN TEANA 2008 Service Manual AUTO LIGHT SYSTEM
EXL-203
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Turns the exterior lamp OFF with the ignition switch ACC or the light switch OFF.
*: The preset time i](/img/5/57391/w960_57391-2231.png)
AUTO LIGHT SYSTEM
EXL-203
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Turns the exterior lamp OFF with the ignition switch ACC or the light switch OFF.
*: The preset time is 45 seconds. The timer operating time can be set by CONSULT-III. Refer to EXL-215,
"HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".
NOTE:
When any position other than the light switch AUTO is set, the auto light system function switches to the exte-
rior lamp battery saver function.
Component Parts LocationINFOID:0000000003894283
Component DescriptionINFOID:0000000003894284
1. Combination switch 2. Optical sensor 3. IPDM E/R
4. BCM
A. Instrument upper panel (RH) B. Engine room (LH) C. Behind the combination meter
J P L I A 111 9 Z Z
Part Description
BCM Detects each switch condition by the combination switch reading function.
Judges the outside brightness from the optical sensor signal.
Judges the OFF timing according to the vehicle condition.
Judges the ON/OFF status of the exterior lamp and each illumination according to the
outside brightness and the vehicle condition.
Requests ON/OFF of each relay to IPDM E/R (with CAN communication).
IPDM E/RControls the integrated relay, and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)Refer to BCS-8, "
System Diagram".
Optical sensor Refer to EXL-238, "
Description".
Page 2233 of 5121
![NISSAN TEANA 2008 Service Manual EXL-204
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
FRONT FOG LAMP SYSTEM
FRONT FOG LAMP SYSTEM
System DiagramINFOID:0000000003894285
System DescriptionINFOID:0000000003894286
OUTLINE
Front fog lamp is contr NISSAN TEANA 2008 Service Manual EXL-204
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
FRONT FOG LAMP SYSTEM
FRONT FOG LAMP SYSTEM
System DiagramINFOID:0000000003894285
System DescriptionINFOID:0000000003894286
OUTLINE
Front fog lamp is contr](/img/5/57391/w960_57391-2232.png)
EXL-204
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
FRONT FOG LAMP SYSTEM
FRONT FOG LAMP SYSTEM
System DiagramINFOID:0000000003894285
System DescriptionINFOID:0000000003894286
OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION
BCM detects the combination switch condition by the combination switch reading function.
BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the front
fog lamp ON condition.
Front fog lamp ON condition
- Front fog lamp switch ON
- Lighting switch 1ST, 2ND or AUTO (auto light function ON judgment)
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the
front fog light request signal.
Combination meter turns the front fog lamp indicator lamp ON according to the front fog light request signal.
JPLIA1083GB
Page 2234 of 5121
![NISSAN TEANA 2008 Service Manual FRONT FOG LAMP SYSTEM
EXL-205
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894287
Component DescriptionINFOID:0000000003894288
1. Fron NISSAN TEANA 2008 Service Manual FRONT FOG LAMP SYSTEM
EXL-205
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894287
Component DescriptionINFOID:0000000003894288
1. Fron](/img/5/57391/w960_57391-2233.png)
FRONT FOG LAMP SYSTEM
EXL-205
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894287
Component DescriptionINFOID:0000000003894288
1. Front fog lamp 2. Combination switch 3. IPDM E/R
4. BCM 5. Front fog lamp indicator lamp
A. Engine room (LH) B. Behind the combination meter C. On the combination meter
JPLIA1121ZZ
Part Description
BCM Detects each switch condition by the combination switch reading function.
Judges the front fog lamp ON/OFF status according to the vehicle condition.
- Requests the front fog lamp relay ON to IPDM E/R (with CAN communication).
IPDM E/RControls the integrated relay and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)Refer to BCS-8, "
System Diagram".
Combination meter
(Front fog lamp indicator lamp)Turn the front fog lamp indicator lamp ON according to the request from BCM (with
CAN communication).
Page 2236 of 5121
![NISSAN TEANA 2008 Service Manual TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
EXL-207
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894291
Component DescriptionINFOID:000 NISSAN TEANA 2008 Service Manual TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
EXL-207
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894291
Component DescriptionINFOID:000](/img/5/57391/w960_57391-2235.png)
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
EXL-207
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Component Parts LocationINFOID:0000000003894291
Component DescriptionINFOID:0000000003894292
1. Hazard switch 2. Front turn signal lamp 3. Combination switch
4. Side turn signal lamp 5. Rear turn signal lamp 6. BCM
7. Turn signal indicator lamp
A. Behind the combination meter B. On the combination meter
JPLIA1122ZZ
Part Description
BCM Detects each switch condition by the combination switch reading function.
Judges the blinks of the turn signal lamp and the hazard warning lamp from each
switch status. The applicable turn signal lamp blinks.
Requests the turn signal indicator lamp blink to the combination meter (with CAN
communication).
Combination switch
(Lighting & turn signal switch)Refer to BCS-8, "
System Diagram".
Hazard switch Inputs the hazard switch ON/OFF signal to BCM.
Combination meter
(Turn signal indicator lamp & buzzer)Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
integrated buzzer according to the request from BCM (with CAN communication).