Ioni NISSAN TEANA 2008 Service Manual

OIL PUMP FITTING BOLT
TM-327
< ON-VEHICLE REPAIR >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
OIL PUMP FITTING BOLT
DescriptionINFOID:0000000003806542
Replace the oil pump fitting bolt and the O-ring if oil leakage or exudes from the oil pump fitting bolt.
Exploded ViewINFOID:0000000003806543
Removal and InstallationINFOID:0000000003806544
REMOVAL
1. Remove Oil pump fitting bolt (1) from transaxle assembly.
2. Remove O-ring from oil pump fitting bolt.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Never reuse oil pump fitting bolt and O-ring.
 Apply CVT fluid to O-ring.
InspectionINFOID:0000000003806545
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to TM-304, "Inspec-
tion".
1. Oil pump fitting bolt 2. O-ring 3. Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to GI-4, "
Components" for symbols not described above.
JPDIA0763GB
JPDIA0077ZZ

TM-328
< ON-VEHICLE REPAIR >[CVT: RE0F10A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded ViewINFOID:0000000003806546
Removal and InstallationINFOID:0000000003806547
REMOVAL
1. Remove air duct (inlet) and air cleaner case. Refer to EM-26, "Exploded View".
1. Remove clip from the bracket.
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Install air breather hose with paint mark facing upward.
 Insert air breather hose a minimum of 17 mm (0.67 in) onto air breather tube (to end of air breather
tubes radius end).
 Install air breather hose to bracket by fully inserting the clip.
 Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
1. Air breather hose 2. Clip 3. Bracket
4. Transaxle assembly
A. Air breather tube B. Paint mark
: Vehicle front
JPDIA0768ZZ

FLUID COOLER SYSTEM
TM-329
< ON-VEHICLE REPAIR >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
FLUID COOLER SYSTEM
Exploded ViewINFOID:0000000003886234
Removal and InstallationINFOID:0000000003886235
REMOVAL
1. Remove air duct (inlet). Refer to EM-26, "Exploded View".
2. Remove engine under cover. Refer to EXT-28, "
Exploded View".
3. Remove fender protector (left side). Refer to EXT-22, "
FENDER PROTECTOR : Exploded View".
4. Remove fluid cooler hose A and fluid cooler hose B.
5. Remove CVT fluid cooler tube from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never reuse copper washer.
1. Hose clamp 2. Fluid cooler hose A 3. Fluid cooler hose B
4. Copper washer 5. CVT fluid cooler tube 6. CVT fluid cooler tube
7. Transaxle assembly
A. To radiator
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA0787GB

FLUID COOLER SYSTEM
TM-331
< ON-VEHICLE REPAIR >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
- Set hose clamps (1) at the both ends of fluid cooler hose (2) with
dimension (A) from the hose edge.
- Hose clamp should not interfere with the bulge of fluid cooler tube.
InspectionINFOID:0000000003886236
After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to TM-304, "Inspection". Dimension A : 5 – 9 mm (0.20 – 0.35 in)
SCIA8123E

TM-332
< REMOVAL AND INSTALLATION >[CVT: RE0F10A]
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded ViewINFOID:0000000003806551
Removal and InstallationINFOID:0000000003806552
WARNING:
Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high
pressure engine coolant escaping from the reservoir tank.
REMOVAL
1. Remove the engine, the transaxle assembly and front suspension member. Refer to EM-67, "Exploded
View".
2. Lift with hoist and separate engine, transaxle assembly from front suspension member. Refer to EM-67,
"Exploded View".
3. Remove air breather hose. Refer to TM-328, "
Exploded View".
4. Remove CVT fluid level gauge and CVT fluid charging pipe.
5. Disconnect the following connectors:
 Primary speed sensor connector
 Secondary speed sensor connector
 PNP switch connector
 CVT unit connector
6. Remove crankshaft position sensor (POS). Refer to EM-38, "
Exploded View".
1. Transaxle assembly 2. O-ring 3. CVT fluid charging pipe
4. CVT fluid level gauge
A. For tightening torque, refer to TM-332, "
Removal and Installation".
B. To water outlet
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA0736GB

TM-334
< REMOVAL AND INSTALLATION >[CVT: RE0F10A]
TRANSAXLE ASSEMBLY
 Align the position of tightening bolts ( ) for drive plate with those
of the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts to the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
 When tightening the tightening bolts for the torque converter
after fixing the crankshaft pulley bolts, confirm the tightening
torque of the crankshaft pulley mounting bolts. Refer to EM-
53, "Removal and Installation".
 After converter is installed to drive plate, rotate crankshaft
several turns and check that transaxle rotates freely without
binding.
InspectionINFOID:0000000003806553
INSPECTION BE FORE INSTALLATION
 After inserting a torque converter to the CVT, check that distance
(A) within the reference value limit.
INSPECTION AFTER INSTALLATION
 After completing installation, check the following item.
- CVT fluid leakage and CVT fluid level. Refer to TM-304, "
Inspection".
- CVT position. Refer to TM-314, "
Inspection and Adjustment".
Insertion direction Transaxle assembly to engine assembly Engine assembly to transaxle assembly
Bolt position A B C D
Number of bolts 2 1 1 4
Bolt length mm (in) 55 (2.17) 35 (1.38) 55 (2.17) 40 (1.57)
Tightening torque N·m (kg-m, ft-lb) 75 (7.7, 55) 50 (5.1, 37)
SCIA1861E
B: Scale
C : Straightedge
Distance A : Refer to TM-338, "Torque Converter".
JPDIA0740ZZ

TM-336
< DISASSEMBLY AND ASSEMBLY >[CVT: RE0F10A]
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Unit: mm (in)
NOTE:
Converter housing oil seal pulling direction is used as the refer-
ence.
 After completing installation, check for CVT fluid leakage and CVT
fluid level. Refer to TM-304, "
Inspection".
 Attach the pawl (A) of the torque converter to the drive sprocket
hole (B) on the transaxle assembly side.
CAUTION:
 Rotate the torque converter for installing torque converter.
 Never damage the bushing inside the torque converter
sleeve when installing the converter housing oil seal.
 Never reuse converter housing oil seal.
 Apply CVT fluid to converter housing oil seal.
InspectionINFOID:0000000003806560
INSPECTION AFTER INSTALLATION
 After inserting a torque converter to the CVT, check distance (A)
within the reference value limit.
Dimension B 1.0 ± 0.5 (0.039 ± 0.020)
SCIA7909J
SCIA7907J
B: Scale
C : Straightedge
Distance A : Refer to TM-338, "Torque Converter".
JPDIA0740ZZ

SERVICE DATA AND SPECIFICATIONS (SDS)
TM-337
< SERVICE DATA AND SPECIFICATIONS (SDS) [CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000003806561
*: Refer to MA-11, "Fluids and Lubricants".
Vehicle Speed When Shifting GearsINFOID:0000000003806562
Numerical value data are reference values.
(rpm)
CAUTION:
Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall SpeedINFOID:0000000003806563
Line PressureINFOID:0000000003806564
kPa (bar, kg/cm2, psi)
*: Reference valuesApplied modelVQ25DE
CVT modelRE0F10A
CVT assembly Model code number 1XF8E
Transmission gear ratioD range 2.349 – 0.394
Reverse 1.750
Final drive 6.120
Recommended fluid NISSAN CVT Fluid NS-2*
Fluid capacity8.3 liter (7-1/4 Imp qt)
CAUTION:
 Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
 Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may dam-
age the CVT, which is not covered by the warranty.
Throttle position Shift patternEngine speed
At 40 km/h (25 MPH) At 60 km/h (37 MPH)
8/8“D” position 3,500 – 4,400 4,700 – 5,600
Sport mode 3,500 – 4,400 4,700 – 5,600
“L” position 3,500 – 4,400 4,700 – 5,600
2/8“D” position 1,300 – 3,100 1,400 – 3,400
Sport mode 2,200 – 3,000 2,800 – 3,600
“L” position 3,300 – 4,200 4,200 – 5,000
Stall speed 2,500 – 2,970 rpm
Engine speed Line pressure
“R”, “D” positions
At idle 750 (7.50, 7.65, 108.8)
At stall
5,700 (57.00, 58.14, 826.5)
*

VTL-4
REAR FOOT DUCT 2 : Removal and Installation ..114
REAR FOOT DUCT 3 ...............................................115
REAR FOOT DUCT 3 : Exploded View .................116
REAR FOOT DUCT 3 : Removal and Installation ..116
FOOT DUCT .............................................................117
FOOT DUCT : Exploded View ...............................117
FOOT DUCT : Removal and Installation ...............118
IONIZER ............................................................119
WITH INTELLIGENT AIR CONDITIONER SYS-
TEM .........................................................................
119
WITH INTELLIGENT AIR CONDITIONER SYS-
TEM : Exploded View ............................................
119
WITH INTELLIGENT AIR CONDITIONER SYS-
TEM : Removal and Installation ............................
119

SWITCHES AND THEIR CONTROL FUNCTION
VTL-5
< FUNCTION DIAGNOSIS >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
FUNCTION DIAGNOSIS
SWITCHES AND THEIR CONTROL FUNCTION
System DescriptionINFOID:0000000003774638
JPIIA0885GB
JSIIA1186GB