high beam NISSAN TEANA 2008 Service Manual

BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
VEH SPEED 1
[km/h]The value of the vehicle speed received from combination meter with CAN commu-
nication
KEY SW-SLOT
[On/Off]Key switch status input from key slot
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function TURN SIGNAL L
[On/Off]
TA I L L A M P S W
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
DOOR SW-DR
[On/Off]The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]The value of exterior brightness voltage input from the optical sensor Monitor item
[Unit]Description
Test item Operation Description
TA I L L A M POnTransmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off Stops the position light request signal transmission.
HEAD LAMPHiTransmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LowTransmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off Stops the high & low beam request signal transmission.
FR FOG LAMPOnTransmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off Stops the front fog lights request signal transmission.

DLK-198
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
CAUTION:
 After installation, inspection and replenish the following.
- Engine coolant. Refer to CO-8, "
Inspection", CO-9, "Refilling".
- CVT fluid. Refer to TM-142, "
Inspection", TM-143, "Changing" (CVT: RE0F09B) or TM-304, "Inspec-
tion", TM-305, "Changing" (CVT: RE0F10A).
 After installation, adjust the following parts.
- Front combination lamp. EXL-174, "
Aiming Adjustment Procedure (Low Beam)", EXL-175, "Aiming
Adjustment Procedure (High Beam)" (XENON TYPE) or EXL-337, "Aiming Adjustment Procedure
(Low Beam)", EXL-338, "Aiming Adjustment Procedure (High Beam)" (HALOGEN TYPE).

DLK-200
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
7. Remove mounting bolts and remove front fender.
CAUTION:
A viscous urethane foam is installed on the back surface of front fender. When removing the front
fender, peel of the urethane foam bit at a time, and carefully to remove it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installation, check front fender adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment" and DLK-203, "DOOR ASSEMBLY : Adjustment".
 After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
 Adjust the following part.
- Front combination lamp: Refer to EXL-174, "
Aiming Adjustment Procedure (Low Beam)", EXL-175,
"Aiming Adjustment Procedure (High Beam)" (XENON TYPE) or EXL-337, "Aiming Adjustment Pro-
cedure (Low Beam)", EXL-338, "Aiming Adjustment Procedure (High Beam)" (HALOGEN TYPE).

EXL-3
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
TAIL LAMP CIRCUIT .........................................74
Component Function Check ....................................74
Diagnosis Procedure ...............................................74
LICENSE PLATE LAMP CIRCUIT .....................76
Component Function Check ....................................76
Diagnosis Procedure ...............................................76
REAR FOG LAMP CIRCUIT ..............................77
Component Function Check ....................................77
Diagnosis Procedure ...............................................77
HEADLAMP SYSTEM ........................................79
Wiring Diagram - HEADLAMP - ..............................79
AUTO LIGHT SYSTEM ......................................83
Wiring Diagram - AUTO LIGHT SYSTEM - .............83
FRONT FOG LAMP SYSTEM ............................87
Wiring Diagram - FRONT FOG LAMP - ..................87
TURN SIGNAL AND HAZARD WARNING
LAMP SYSTEM ..................................................
90
Wiring Diagram - TURN AND HAZARD WARN-
ING LAMPS - ..........................................................
90
PARKING, LICENSE PLATE AND TAIL
LAMPS SYSTEM ................................................
95
Wiring Diagram - PARKING, LICENSE PLATE
AND TAIL LAMPS - .................................................
95
STOP LAMP .......................................................99
Wiring Diagram - STOP LAMP - .............................99
BACK-UP LAMP ..............................................102
Wiring Diagram - BACK-UP LAMP - .....................102
REAR FOG LAMP SYSTEM ............................105
Wiring Diagram - REAR FOG LAMP - ..................105
ECU DIAGNOSIS .......................................108
BCM (BODY CONTROL MODULE) .................108
Reference Value ...................................................108
Wiring Diagram - BCM - ........................................131
Fail-safe ................................................................137
DTC Inspection Priority Chart .............................139
DTC Index ............................................................140
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ...............
142
Reference Value ...................................................142
Wiring Diagram - IPDM E/R - ................................150
Fail-safe ................................................................153
DTC Index ............................................................155
AUTO LEVELIZER CONTROL UNIT ...............156
Reference Value ...................................................156
Wiring Diagram — HEADLAMP AIMING CON-
TROL SYSTEM — ................................................
158
Fail-safe ................................................................161
DTC Inspection Priority Chart ...............................162
DTC Index .............................................................163
SYMPTOM DIAGNOSIS ............................164
EXTERIOR LIGHTING SYSTEM SYMPTOMS .164
Symptom Table .....................................................164
NORMAL OPERATING CONDITION .............167
Description .............................................................167
BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON ...................................................
168
Description .............................................................168
Diagnosis Procedure .............................................168
BOTH SIDE HEADLAMPS (LO) ARE NOT
TURNED ON ...................................................
169
Description .............................................................169
Diagnosis Procedure .............................................169
PARKING, LICENSE PLATE AND TAIL
LAMPS ARE NOT TURNED ON .....................
170
Description .............................................................170
Diagnosis Procedure .............................................170
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON ...................................................
171
Description .............................................................171
Diagnosis Procedure .............................................171
PRECAUTION ............................................172
PRECAUTIONS ...............................................172
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
172
Precautions For Xenon Headlamp Service ...........172
ON-VEHICLE MAINTENANCE ..................173
HEADLAMP AIMING ADJUSTMENT .............173
Description .............................................................173
Aiming Adjustment Procedure (Low Beam) ...........174
Aiming Adjustment Procedure (High Beam) ..........175
FRONT FOG LAMP AIMING ADJUSTMENT .178
Description .............................................................178
Aiming Adjustment Procedure ...............................178
ON-VEHICLE REPAIR ...............................180
FRONT COMBINATION LAMP ......................180
Exploded View .......................................................180
Removal and Installation .......................................181
Replacement .........................................................181
Disassembly and Assembly ...................................182
FRONT FOG LAMP ........................................183
Exploded View .......................................................183
Removal and Installation .......................................183
Replacement .........................................................183

EXL-6
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON ....................................................
334
Description .............................................................334
Diagnosis Procedure .............................................334
PRECAUTION ............................................335
PRECAUTIONS ...............................................335
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................
335
ON-VEHICLE MAINTENANCE ..................336
HEADLAMP AIMING ADJUSTMENT .............336
Description .............................................................336
Aiming Adjustment Procedure (Low Beam) ...........337
Aiming Adjustment Procedure (High Beam) ..........338
FRONT FOG LAMP AIMING ADJUSTMENT .341
Description .............................................................341
Aiming Adjustment Procedure ...............................341
ON-VEHICLE REPAIR ...............................343
FRONT COMBINATION LAMP .......................343
Exploded View .......................................................343
Removal and Installation .......................................343
Replacement .........................................................344
Disassembly and Assembly ...................................344
FRONT FOG LAMP .........................................346
Exploded View .......................................................346
Removal and Installation .......................................346
Replacement .........................................................346
OPTICAL SENSOR .........................................348
Exploded View .......................................................348
Removal and Installation .......................................348
LIGHTING & TURN SIGNAL SWITCH ............349
Exploded View ......................................................349
Removal and Installation .......................................349
HEADLAMP AIMING SWITCH .........................350
Exploded View ......................................................350
Removal and Installation .......................................350
HAZARD SWITCH ............................................351
Exploded View ......................................................351
Removal and Installation .......................................351
SIDE TURN SIGNAL LAMP .............................352
Exploded View ......................................................352
Removal and Installation .......................................352
REAR COMBINATION LAMP ..........................354
Exploded View ......................................................354
Removal and Installation .......................................354
Replacement .........................................................355
HIGH-MOUNTED STOP LAMP ........................356
Exploded View ......................................................356
Removal and Installation .......................................356
REAR FOG LAMP ............................................357
Exploded View ......................................................357
Removal and Installation .......................................357
Replacement .........................................................357
LICENSE PLATE LAMP ...................................358
Exploded View ......................................................358
Removal and Installation .......................................358
Replacement .........................................................358
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
360
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
360
Bulb Specifications ................................................360

HEADLAMP SYSTEM
EXL-11
< FUNCTION DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
FUNCTION DIAGNOSIS
HEADLAMP SYSTEM
System DiagramINFOID:0000000003774356
System DescriptionINFOID:0000000003774357
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
 BCM detects the combination switch condition with the combination switch reading function.
 BCM transmits the low beam request signal to IPDM E/R with CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition- Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment)
 IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
 BCM transmits the high beam request signal to IPDM E/R and the combination meter with CAN communica-
tion according to the headlamp (HI) ON condition.
Headlamp (HI) ON condition- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
 Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
 IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
JPLIA0168GB

EXL-12
< FUNCTION DIAGNOSIS >[XENON TYPE]
HEADLAMP SYSTEM
Component Parts Location
INFOID:0000000003774358
Component DescriptionINFOID:0000000003774359
1. Headlamp (HI) 2. Headlamp (LO) 3. Combination switch
4. IPDM E/R 5. BCM 6. High beam indicator lamp
A. Engine room (LH) B. Behind the combination meter C. On the combination meter
J P L I A 111 8 Z Z
Part Description
BCM Detects each switch condition by the combination switch reading function.
 Judges that the headlamp is turned ON according to the vehicle condition.
- Requests the headlamp relay (HI/LO) ON to IPDM E/R (with CAN communication).
- Requests the high beam indicator lamp ON to the combination meter (with CAN
communication).
IPDM E/RControls the integrated relay, and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)Refer to BCS-8, "
System Diagram".
Combination meter
(High beam indicator lamp)Turns the high beam indicator lamp ON according to the request from BCM (with CAN
communication).

EXL-30
< FUNCTION DIAGNOSIS >[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)INFOID:0000000003773549
WORK SUPPORT
*: Factory setting
DATA MONITOR
DOOR SW-RR
[On/Off]The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]The value of exterior brightness voltage input from the optical sensor Monitor item
[Unit]Description
Test item Operation Description
TA I L L A M POnTransmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off Stops the position light request signal transmission.
HEAD LAMPHiTransmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LowTransmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off Stops the high & low beam request signal transmission.
FR FOG LAMPOnTransmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off Stops the front fog lights request signal transmission.
RR FOG LAMPOn Outputs the voltage to turn the rear fog lamp ON.
 Transmits the rear fog lamp status signal to the combination meter with
CAN communication to turn the rear fog lamp indicator lamp ON.
Off Stops the voltage to turn the rear fog lamp OFF.
 Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHTOn
NOTE:
The item is indicated, but cannot be tested.
Off
CORNERING LAMPRH
NOTE:
The item is indicated, but cannot be tested. LH
Off
ILL DIM SIGNALOn
NOTE:
The item is indicated, but cannot be tested.
Off
Service item Setting item Setting
HAZARD ANSWER
BACKLock Only* With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob. Unlk Only With unlocking only
Lock/Unlk With locking/unlocking
Off Without the function

EXL-34
< FUNCTION DIAGNOSIS >[XENON TYPE]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT-III Function (IPDM E/R)
INFOID:0000000003894260
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
Refer to EXL-155, "DTCIndex".
DATA MONITOR
Monitor item
Cooling fan does not operatePerform auto active test.
Does the cooling fan operate?YES ECM signal input circuit
 CAN communication signal
between ECM and IPDM E/
R
NO Harness or connector be-
tween IPDM E/R and cool-
ing fan motor
 Harness or connector be-
tween IPDM E/R and cool-
ing fan relay
 Cooling fan motor
 Cooling fan relay
IPDM E/R Symptom Inspection contents Possible cause
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]MAIN SIG-
NALSDescription
MOTOR FAN REQ
[1/2/3/4]×Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]×Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TA I L & C L R R E Q
[Off/On]×Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]×Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]×Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]×Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]×Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]×Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]×Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]Displays the status of the ignition switch ON signal received from BCM via CAN
communication.

EXL-54
< COMPONENT DIAGNOSIS >[XENON TYPE]
HEADLAMP (HI) CIRCUIT
HEADLAMP (HI) CIRCUIT
Component Function CheckINFOID:0000000003774352
1.CHECK HEADLAMP (HI) OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "
Diagnosis Description".
2. Check that the headlamp switches to the high beam.
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (HI) is turned ON.
NOTE:
ON/OFF is repeated 1 second each.
Is the headlamp (HI) turned ON?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-54, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003774353
1.CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch OFF.
2. Disconnect the headlamp high connector.
3. Turn the ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the headlamp high harness connector. Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF
Te r m i n a l s
Te s t i t e m
Voltag e
(Approx.) (+) (−)
IPDM E/R
GroundEXTERNAL
LAMPS
Connector Terminal
RH
E34589HiBattery
voltage
Off 0 V
LH 90HiBattery
voltage
Off 0 V