display NISSAN TEANA 2008 Service Manual

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-425
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
CONFIRMATION/ADJUSTMENT MODE
1. Start the diagnosis function and select “Confirmation/Adjustment”. The confirmation/adjustment mode
indicates where each item can be checked or adjusted.
2. Select each switch on the “Confirmation/Adjustment Mode”
screen to display the relevant trouble diagnosis screen. Press
the “BACK” switch to return to the initial Confirmation/Adjust-
ment Mode screen.
Display Diagnosis
TEL antenna connection malfunction
is detected.Replace TEL antenna.
NAVI control unit power supply and
ground circuits are malfunctioning.NAVI control unit power supply and
ground circuits. Area with yellow connection lines DescriptionPossible malfunction location / Action
to take
JSNIA1324GB
JPNIA1106GB
JSNIA0489GB
JSNIA0148GB

AV-426
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
The tint of the color bar indication is as per the following list if RGB signal error is detected.
Vehicle Signals
A comparison check can be made of each actual vehicle signal and
the signals recognized by the AV control unit.
Navigation/Phone
Handsfree Voice Microphone Test
 Microphone speaker check can be performed. A microphone input
level is displayed.
Color Spectrum Bar
R (red) signal error : Light blue (Cyan) tint
G (green) signal error : Purple (Magenta) tint
B (blue) signal error : Yellow tint
JSNIA0149GB
Diagnosis item Display Vehicle status Remarks
Vehicle speed ONVehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed. This is normal. Vehicle speed = 0 km/h (0 MPH)
Parking brakeON Parking brake is applied.
OFF Parking brake is released.
LightsON Light switch ON.
—
OFF Light switch OFF.
IgnitionON Ignition switch ON.
—
OFF Ignition switch in ACC position.
ReverseON Selector lever in R position.
Changes in indication may be delayed. This is normal.
OFFSelector lever in any position other
than R.
JSNIA0490GB

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-427
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 A color tone can be checked by the color bar display.
NOTE:
The tint of the color bar indication is as per the following list if RGB
signal error is detected.
Gradation Bar A color tone can be checked by the color bar display.
Touch Panel Touch panel response check can be performed.
Vehicle Signals
 A comparison check can be made of each actual vehicle signal
and the signals recognized by the NAVI control unit.R (red) signal error : Light blue (Cyan) tint
G (green) signal error : Purple (Magenta) tint
B (blue) signal error : Yellow tint
JSNIA0491GB
JSNIA0492GB
JSNIA0493GB
JSNIA0516GB
Diagnosis item Display Vehicle status Remarks
Vehicle speedON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed. This is normal. OFF Vehicle speed = 0 km/h (0 MPH)
Parking brakeON Parking brake is applied.
OFF Parking brake is released.

AV-428
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Confirm/Change Bluetooth Passkey
 The passkey of Bluetooth can be confirmed and changed.
 The passkey can be changed by four to eight digits within the num-
ber of 0 to 9.
Confirm/Change Bluetooth Device Name
 The device name of Bluetooth can be confirmed and changed.
 The device name can be changed within the range of twenty digits
of alphabets and codes.
Speaker Test
Select “SPEAKER TEST” to display the Speaker Diagnosis screen.
Press “START and NEXT” to generate a test tone in a speaker.
Press “Start” to generate a test tone in the next speaker. Press “End”
to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to HAC-159, "
WITH INTELLIGENT AIR CONDITIONER SYSTEM : CONSULT-III Function" for details.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The frequency of occurrence in error history is displayed in a count up manner. The actual count up method
differs depending on the error item.
Count up method A
LightsON Light switch ON.
—
OFF Light switch OFF.
ReverseON Selector lever in R position.
Changes in indication may be delayed. This is normal.
OFFSelector lever in any position other
than R. Diagnosis item Display Vehicle status Remarks
JSNIA0086GB
JSNIA0517GB
Tweeter : 3 kHz
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
JSNIA0150GB

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-429
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the
condition is normal at a next IGN ON cycle.
 The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
 The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even if
the condition is normal at the next IGN ON cycle.
 The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
Display type of occur-
rence frequencyError history display item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B Other than the above
JSNIA0518GB
Error item Description Possible malfunction factor/Action to take
CAN COMM CIRCUITCAN communication malfunction is detect-
ed.Perform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
CONTROL UNIT (CAN)CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit. CONTROL UNIT (AV)AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
CAN Controller Memory Error
Amplifier Temperature Error BOSE amp. malfunction is detected. Replace the BOSE amp.
Front Display Connection ErrorWhen either one of the following items is
detected:
 display unit power supply and ground cir-
cuits are malfunctioning.
 serial communication circuits between
display unit and AV control unit are mal-
functioning.
 serial communication signal between
display unit and AV control unit is mal-
functioning. Display unit power supply and ground
circuits.
 Serial communication circuits between
display unit and AV control unit.

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-433
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P Vehicle CAN Diagnosis
 CAN communication status and error counter is displayed.
 The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 The error counter is erased if reset.
AV COMM Diagnosis
 Displays the communication status between AV control unit (mas-
ter unit) and each unit.
 The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 If it resets, the error counter is erased.
Delete Unit Connection Log
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed)
Initialize Settings
Items Display (Current)Malfunction counter
(Past)
Tx (HVAC) OK / UNKWN OK / 0 – 39
Rx (ECM) OK / UNKWN OK / 0 – 39
Rx (Cluster) OK / UNKWN OK / 0 – 39
Rx (BCM) OK / UNKWN OK / 0 – 39
Rx (HVAC) OK / UNKWN OK / 0 – 39
Rx (USM) OK / UNKWN OK / 0 – 39
JSNIA1287GB
ItemsStatu s
(Current)Counter
(Past)
C Tx(ITM–SW) OK / UNKWN OK / 0 – 39
C Rx(PrimarySW–ITM) OK / UNKWN OK / 0 – 39
C Rx(RrSeatSW–ITM) OK / UNKWN OK / 0 – 39
C Rx(Amp–ITM) OK / UNKWN OK / 0 – 39
C Rx(RearCamera–ITM) OK / UNKWN OK / 0 – 39
C Rx(DVD–ITM) OK / UNKWN OK / 0 – 39
C Rx(DVDNavi–ITM) OK / UNKWN OK / 0 – 39
C Rx(AmpAudio–ITM) OK / UNKWN OK / 0 – 39
C Rx(DVDAudio–ITM) OK / UNKWN OK / 0 – 39
JSNIA1292GB
JSNIA0522GB

AV-434
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Initializes the AV control unit memory.
CONSULT-III Function (MULTI AV)INFOID:0000000003765848
CONSULT-III FUNCTIONS
CONSULT-III performs the following functions via the communication with the AV control unit.
CAUTION:
Be sure to turn the ignition switch OFF once after using CONSULT-III. (Navigation system may mal-
function if normally used when the ignition switch is not turned OFF after using CONSULT-III.)
AV COMMUNICATION
When “AV communication” of “CAN Diag Support Monitor” is selected, the following function will be performed.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
 In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
 The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis Results Display Item
JSNIA0155GB
Diagnosis mode Description
Ecu Identification The part number of AV control unit can be checked.
Self Diagnostic ResultPerforms a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
Data Monitor The diagnosis of vehicle signal that is input to the AV control unit can be performed.
AV communicationAV&NAVI C/UDisplays the communication status from AV control unit to each unit as well as the error
counter.
AUDIO Displays the AV control unit communication status and the error counter.
Error item Detection logic Possible malfunction factor/Action to take
CAN COMM CIRCUIT [U1000]CAN communication malfunction is detect-
ed.Refer to AV- 4 4 0 , "
DiagnosisProcedure".
CONTROL UNIT (CAN) [U1010]CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit.
Refer to AV- 6 4 8 , "
Removal and Installa-
tion". CONTROL UNIT (AV) [U1310]AV communication circuit initial diagnosis
malfunction is detected.
Control Unit FLASH-ROM [U1200]
AV control unit malfunction is detected.
CAN CONT [U1216]
AMP TEMP [U1231] BOSE amp. is detected.Replace the BOSE amp.
Refer to AV- 6 5 7 , "
Removal and Installa-
tion".

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-435
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
FRONT DISP CONN [U1243]When either one of the following items is
detected:
 display unit power supply and ground cir-
cuits are malfunctioning.
 serial communication circuits between
display unit and AV control unit are mal-
functioning.
 serial communication signal between
display unit and AV control unit is mal-
functioning. Display unit power supply and ground
circuits.
Refer toAV- 4 6 5 , "DISPLAY UNIT : Diag-
nosis Procedure".
 Serial communication circuits between
display unit and AV control unit
CAMERA CONT. CONN [U1250]Camera connection recognition signal cir-
cuit malfunction is detected.Camera connection recognition signal cir-
cuit.
Refer to AV- 4 4 8 , "
Diagnosis Procedure".
CENTER SP OPEN [U1260]Sound signal center speaker circuit is
open.Check sound signal center speaker circuit.
CENTER SP SHORT [U1261]Sound signal center speaker circuit is
shorted between center speaker signal (+)
and center speaker signal (-).Check sound signal center speaker circuit.
CENTER SP GND-SHORT [U1262]Sound signal center speaker circuit to
ground is shorted.Check sound signal center speaker circuit.
CENTER SP VB-SHORT [U1263]Sound signal center speaker circuit to bat-
tery is shorted.Check sound signal center speaker circuit.
FR-DOOR SP OPEN [U1264]Sound signal front speaker RH circuit is
open.Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP SHORT [U1265]Sound signal front speaker RH circuit is
shorted between front speaker RH signal
(+) and front speaker RH signal (-).Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP GND-SHORT [U1266]Sound signal front speaker RH circuit to
ground is shorted.Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP VB-SHORT [U1267]Sound signal front speaker RH circuit to
battery is shorted.Check sound signal front speaker RH cir-
cuit.
RR-SP/FR-WOOFER OPEN [U1268]Sound signal rear speaker LH circuit is
open.Check sound signal rear speaker LH circuit.
RR-SP/FR-WOOFER SHORT [U1269]Sound signal rear speaker LH circuit is
shorted between rear speaker LH signal (+)
and rear speaker LH signal (-).Check sound signal rear speaker LH circuit.
RR-SP/FR-WOOFER GND-SHORT
[U126A]Sound signal rear speaker LH circuit to
ground is shorted.Check sound signal rear speaker LH circuit.
RR-SP/FR-WOOFER VB-SHORT [U126B]Sound signal rear speaker LH circuit to bat-
tery is shorted.Check sound signal rear speaker LH circuit.
RR-SURROUND SP OPEN [U126C] Sound signal woofer RH circuit is open. Check sound signal woofer RH circuit.
RR-SURROUND SP SHORT [U126D]Sound signal woofer RH circuit is shorted
between woofer RH signal (+) and woofer
RH signal (-).Check sound signal woofer RH circuit.
RR-SURROUND SP GND-SHORT
[U126E]Sound signal woofer RH circuit to ground is
shorted.Check sound signal woofer RH circuit.
RR-SURROUND SP VB-SHORT [U126F]Sound signal woofer RH circuit to battery is
shorted.Check sound signal woofer RH circuit.
RL-SURROUND SP OPEN [U1274] Sound signal woofer LH circuit is open. Check sound signal woofer LH circuit.
RL-SURROUND SP SHORT [U1275]Sound signal woofer LH circuit is shorted
between woofer LH signal (+) and woofer
LH signal (-).Check sound signal woofer LH circuit.
RL-SURROUND SP GND-SHORT [U1276]Sound signal woofer LH circuit to ground is
shorted.Check sound signal woofer LH circuit. Error item Detection logic Possible malfunction factor/Action to take

AV-438
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DATA MONITOR
ALL SIGNALS
 Displays the status of the following vehicle signals inputted to the AV control unit.
 For each signal, actual signal can be compared with the condition recognized on the system.
SELECTION FROM MENU
Allows the technician to select which vehicle signals should be displayed and displays the status of the
selected vehicle signals.
 AV COMM CIRCUIT [U1300]
 DVD DECK CONN [U1248]
 AMP CONN [U124E]
 REAR-CAMERA LAN CONN [U1252]
 DVD NAVI CONN [U125D]With rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between rear control
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.  AV communication circuits between mul-
tifunction switch and rear control switch.
 AV communication circuits between rear
control switch and camera control unit.
Without rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between multifunction
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.AV communication circuits between multi-
function switch and camera control unit.
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 DVD DECK CONN [U1248]
 AMP CONN [U124E]
 REAR-CAMERA LAN CONN [U1252]
 DVD NAVI CONN [U125D]When either one of the following items is
detected:
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
 AV communication signal between AV
control unit and multifunction switch is
malfunctioning.AV communication circuits between AV
control unit and multifunction switch. Error item Detection logic Possible malfunction factor/Action to take
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGOn Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is nor-
mal. Off Vehicle speed =0 km/h (0 MPH)
PKB SIGOn Parking brake is applied.
Off Parking brake is released.
ILLUM SIGOn Light switch ON.
— Off Light switch OFF.
IGN SIGOn Ignition switch ON.
Off Ignition switch in ACC position.
REV SIGOn Selector lever in R position.
Changes in indication may be delayed. This is nor-
mal.
OffSelector lever in any position other
than R.

AV-440
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000003765851
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each
control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-22, "
CAN Communication Signal Chart".
DTC LogicINFOID:0000000003765852
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000003765853
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of “MULTI AV”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to “LAN system”. Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI section. Refer to GI-35, "
Intermittent Incident".
DTCDisplay contents of CON-
SULT-IIIDiagnostic item is detected when... Probable malfunction location
U1000 CAN COMM CIRCUITWhen AV control unit is not transmitting or re-
ceiving CAN communication signal for 2 sec-
onds or more.CAN communication system