key NISSAN TEANA 2008 Service Manual

DLK-212
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
Check rear door open/close operation after installation.

TRUNK LID
DLK-213
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded ViewINFOID:0000000003813412
REMOVAL
ADJUSTMENT
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

DLK-214
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000003813413
CAUTION:
Operate with two workers, because of its heavy weight.
REMOVAL
1. Remove the trunk lid finisher inner. Refer to INT-59, "Removal and Installation"
2. Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.
3. Remove trunk lid stay at trunk lid side. Refer to DLK-218, "
TRUNK LID STAY : Removal and Installation".
4. Remove the trunk lid hinge mounting bolts on trunk lid side and remove the trunk lid assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
 Check trunk lid open/close, lock/unlock operation after installation.
 After installation, perform fitting adjustment. Refer to DLK-215, "
TRUNK LID ASSEMBLY : Adjust-
ment".
1. Trunk lid assembly 2. Trunk lid hinge 3. Trunk lid striker
4. Body side outer 5. Rear combination lamp 6. Rear bumper fascia
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2393GB

TRUNK LID
DLK-215
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID ASSEMBLY : AdjustmentINFOID:0000000003813414
Check the clearance and surface height between trunk lid and each part by visually and touching.
If the clearance and surface height are out of specification, adjust them according to the procedures shown
below.
Unit: mm (in)
1. Loosen trunk lid hinge mounting bolts (trunk lid side).
2. Remove trunk rear finisher. Refer to INT-57, "
Removal and Installation".
3. Loosen trunk lid striker mounting bolts.
4. Lift up trunk lid approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that it
is engaged firmly with trunk lid closed.
5. Check the clearance and surface height.
6. Finally tighten trunk lid hinge and trunk lid striker.
7. Install trunk rear finisher. Refer to INT-57, "
Removal and Installation".
TRUNK LID STRIKER ADJUSTMENT
Adjust trunk lid striker so that it becomes parallel with trunk lid lock insertion direction.
TRUNK LID STRIKER
Portion StandardDifference
(RH/LH, MAX)
Trunk lid – Body side outer A – AD Clearance2.5 – 4.5
(0.098 – 0.177)1.0 (0.039)
ESurface
height−1.5 – 0.5
(−0.059 – 0.020)1.4 (0.055)
Trunk lid – Rear combina-
tion lampB – BF Clearance2.9 – 6.5
(0.114 – 0.256)2.0 (0.079)
GSurface
height−2.3 – 1.3
(−0.091 – 0.051)2.0 (0.079)
Trunk lid – Rear bumper fas-
ciaC – C H Clearance5.0 – 9.0
(0.197 – 0.354)—

DLK-216
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STRIKER : Exploded View
INFOID:0000000003819763
TRUNK LID STRIKER : Removal and InstallationINFOID:0000000003813416
REMOVAL
1. Remove trunk rear finisher. Refer to INT-57, "Removal and Installation".
2. Remove mounting bolts, and then remove trunk lid striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Check trunk lid open/close, lock/unlock operation after installation.
 When removing and installing trunk lid striker, perform the fitting adjustment. Refer to DLK-215,
"TRUNK LID ASSEMBLY : Adjustment".
TRUNK LID HINGE
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B.: Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

TRUNK LID
DLK-217
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID HINGE : Exploded ViewINFOID:0000000003819765
TRUNK LID HINGE : Removal and InstallationINFOID:0000000003813418
REMOVAL
1. Remove trunk lid assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal and Installation".
2. Remove trunk lid stay from trunk lid hinge. Refer to DLK-218, "
TRUNK LID STAY : Removal and Installa-
tion".
3. Remove trunk lid hinge mounting nuts (body side), and then remove trunk lid hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Check trunk lid open/close, lock/unlock operation after installation.
 Check trunk lid hinge rotating part for poor lubrication. If necessary, apply body grease.
 When removing and installing trunk lid assembly, perform the fitting adjustment. Refer to DLK-215,
"TRUNK LID ASSEMBLY : Adjustment".
 After installation, apply touch-up paint (the body color) onto the head of trunk lid hinge mounting
bolts.
TRUNK LID STAY
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

DLK-218
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Exploded View
INFOID:0000000003819766
TRUNK LID STAY : Removal and InstallationINFOID:0000000003813420
REMOVAL
1. Support trunk lid with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the trunk lid open when removing the trunk
lid stay.
2. Remove the metal clip (3) located on the connection between
the trunk lid stay (1) and the stud ball (2) (trunk lid side) by using
a flat-bladed screwdriver (A).
3. Remove trunk lid stay (trunk lid side).
4. In the same way, remove trunk lid stay (body side).
INSTALLATION
Install in the reverse order of removal.
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B.: Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB
JMKIA2255ZZ

TRUNK LID
DLK-219
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LID WEATHER-STRIP : Exploded ViewINFOID:0000000003819767
TRUNK LID WEATHER-STRIP : Removal and InstallationINFOID:0000000003813422
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1. Working from the upper section, align weather-strip center mark (upper) with vehicle center position mark
and install weather-strip onto the vehicle.
2. For the lower section, align weather-strip center mark (lower) with center of trunk lid striker.
3. Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Check that weather-strip fits tightly in each corner.
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

DLK-220
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded ViewINFOID:0000000003813423
Removal and InstallationINFOID:0000000003813424
REMOVAL
CAUTION:
Check wiring of hood lock control cable before removal.
1. Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
2. Disconnect hood lock control cable (2) from hood lock assembly.
3. Disconnect bell crank assembly cable from hood lock assembly.
4. Remove air duct (inlet). Refer to EM-26, "
Removal and Installation".
5. Disconnect hood switch connector and remove hood lock assembly.
6. Remove bolts and remove bell crank assembly.
1. Hood lock 2. Hood switch 3. Bell crank assembly
4. Hood lock control cable 5. Hood lock opener
: Clip
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2381ZZ
JMKIA1914ZZ

HOOD LOCK
DLK-221
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
7. Disconnect hood lock control cable from instrument lower panel (LH).
8. Remove fender protector (LH). Refer to EXT-22, "
FENDER PROTECTOR : Removal and Installation".
9. Remove hood lock control cable clamp.
10. Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Never bend cable too much. Keeping the radius 100 mm (3.937 in) or more.
 Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (A) properly.
 Check that hood lock control cable is properly engaged with hood lock.
 After installation, perform hood fitting adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment".
 After installation, perform hood lock control inspection. Refer to DLK-221, "
Inspection".
InspectionINFOID:0000000003813425
NOTE:
If the hood lock cable is bent or deformed, replace it.
1. Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2. While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3. Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4. Install so that static closing force of hood is 94 – 490 N (9.6 – 50.0 kg, 21.1 – 110 lb).
NOTE:
 Exert vertical force on right side and left side of hood lock.
 Do not simultaneously press both sides.
5. Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
JMKIA2398ZZ