Trans NISSAN TEANA 2008 Owner's Guide

AV
U1250 CAMERA CONTROL UNIT
AV-79
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1250 CAMERA CONTROL UNIT
DescriptionINFOID:0000000003882728
DTC LogicINFOID:0000000003882729
Diagnosis ProcedureINFOID:0000000003901201
1.CHECK CONTINUITY RECOGNITION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector and camera control unit connector.
3. Check continuity between AV control unit harness connector and camera control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Connect AV control unit connector and camera control unit connector.
2. Turn ignition switch ON.
3. Check signal between AV control unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace AV control unit.
Part name Description
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
 Power supply is transmitted to rear view camera.
 AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
 Camera control unit is connected via AV communication.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Possible causes
U1250CAMERA CONT. CONN
[U1250]Malfunction is detected in camera connection recogni-
tion signal circuit.Camera connection recognition sig-
nal circuit.
AV control unit Camera control unit
Continuity
Connector Terminals Connector Terminals
M130 68 B251 14 Existed
AV control unit
GroundContinuity
Connector Terminals
M130 68 Not existed
(+)
(−) ConditionVo l ta g e
(Approx.) AV control unit
Connector Terminal
M130 68 GroundConnected camera
control unit connector0 V
Disconnect camera
control unit connector5 V

AV-86
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
RGB (R: RED) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY UNIT)
RGB (R: RED) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY UNIT)
DescriptionINFOID:0000000003882739
Transmit the image displayed with AV control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000003901206
1.CHECK CONTINUITY RGB (R: RED) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (R: RED) SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace display unit.
NO >> Replace AV control unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 17M12940 Existed
Display unit
GroundContinuity
Connector Terminal
M49 17 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 17 GroundStart Confirmation / Adjustment
mode, and then display color bar
by selecting “Color Spectrum Bar”
on DISPLAY DIAGNOSIS screen.
SKIB2238J

AV
RGB (G: GREEN) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY UNIT)
AV-87
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RGB (G: GREEN) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY
UNIT)
DescriptionINFOID:0000000003882741
Transmit the image displayed with AV control unit or NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000003901207
1.CHECK CONTINUITY RGB (G: GREEN) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (G: GREEN) SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace display unit.
NO >> Replace AV control unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 6 M129 39 Existed
Display unit
GroundContinuity
Connector Terminal
M49 6 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 6 GroundStart Confirmation / Adjustment
mode, and then display color bar
by selecting “Color Spectrum Bar”
on DISPLAY DIAGNOSIS screen.
SKIB2236J

AV-88
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
RGB (B: BLUE) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY UNIT)
RGB (B: BLUE) SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY UNIT)
DescriptionINFOID:0000000003882743
Transmit the image displayed with AV control unit or NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000003901208
1.CHECK CONTINUITY RGB (B: BLUE) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (B: BLUE) SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace display unit.
NO >> Replace AV control unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 18M12938 Existed
Display unit
GroundContinuity
Connector Terminal
M49 18 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 18 GroundStart Confirmation / Adjustment
mode, and then display color bar
by selecting “Color Spectrum Bar”
on DISPLAY DIAGNOSIS screen.
SKIB2237J

AV
RGB SYNCHRONIZING SIGNAL CIRCUIT (AV CONTROL UNIT TO DISPLAY
UNIT)
AV-89
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RGB SYNCHRONIZING SIGNAL CIRCUIT (AV CONTROL UNIT TO DIS-
PLAY UNIT)
DescriptionINFOID:0000000003882745
Transmit the RGB synchronizing signal to the display unit so as to synchronize the RGB image displayed with
AV control unit or NAVI control unit.
Diagnosis ProcedureINFOID:0000000003901209
1.CHECK CONTINUITY RGB SYNCHRONIZING SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace display unit.
NO >> Replace AV control unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 19M12941 Existed
Display unit
GroundContinuity
Connector Terminal
M49 19 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 19 Ground —
SKIB3603E

AV-90
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
RGB AREA (YS) SIGNAL CIRCUIT
RGB AREA (YS) SIGNAL CIRCUIT
DescriptionINFOID:0000000003882747
Transmits the display area of RGB image displayed by AV control unit or NAVI control unit with RGB area (YS)
signal to display unit.
Diagnosis ProcedureINFOID:0000000003901210
1.CHECK CONTINUITY RGB AREA (YS) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector terminal 9 and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace display unit.
NO >> Replace AV control unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 9 M129 43 Existed
Display unit
GroundContinuity
Connector Terminal
M49 9 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 9 GroundWhen RGB image is displayed. Approx. 5 V
When AUX image is displayed.
PKIB4948J

AV
HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
AV-91
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
DescriptionINFOID:0000000003882749
In composite image (AUX image, camera image), transmit the vertical synchronizing (VP) signal and horizon-
tal synchronizing (HP) signal from display unit to AV control unit so as to synchronize the RGB images dis-
played with AV control unit such as the image quality adjusting menu, etc.
Diagnosis ProcedureINFOID:0000000003901211
1.CHECK CONTINUITY HORIZONTAL SYNCHRONIZING (HP) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK HORIZONTAL SYNCHRONIZING (HP) SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace AV control unit.
NO >> Replace display unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 8 M129 45 Existed
Display unit
GroundContinuity
Connector Terminal
M49 8 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 8 Ground —
SKIB3601E

AV-92
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
DescriptionINFOID:0000000003882751
In composite image (AUX image, camera image), transmit the vertical synchronizing (VP) signal and horizon-
tal synchronizing (HP) signal from display unit to AV control unit so as to synchronize the RGB images dis-
played with AV control unit such as the image quality adjusting menu, etc.
Diagnosis ProcedureINFOID:0000000003901212
1.CHECK CONTINUITY VERTICAL SYNCHRONIZING (VP) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VERTICAL SYNCHRONIZING (VP) SIGNAL
1. Connect display unit connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal and ground using an oscilloscope.
Is inspection result normal?
YES >> Replace AV control unit.
NO >> Replace display unit.
Display unit AV control unit
Continuity
Connector Terminal Connector Terminal
M49 20M12957 Existed
Display unit
GroundContinuity
Connector Terminal
M49 20 Not existed
(+)
(−) Condition Reference value Display unit
Connector Terminal
M49 20 Ground —
SKIB3598E

AV
AUX IMAGE SIGNAL CIRCUIT
AV-93
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUX IMAGE SIGNAL CIRCUIT
DescriptionINFOID:0000000003882753
Transmits the image signal of external device from auxiliary input jacks to AV control unit.
Diagnosis ProcedureINFOID:0000000003882754
1.CHECK CONTINUITY AUX IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect auxiliary input jacks connector and AV control unit connector.
3. Check continuity between auxiliary input jacks harness connector and AV control unit harness connector.
4. Check continuity between auxiliary input jacks harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AUX IMAGE SIGNAL
1. Connect auxiliary input jacks connector and AV control unit connector.
2. Turn ignition switch ON.
3. Make AUX image signal being input.
4. Check signal between auxiliary input jacks harness connector using an oscilloscope.
Is inspection result normal?
YES >> Replace AV control unit.
NO >> Check that there is no malfunction in the external device.
Auxiliary input jacks AV control unit
Continuity
Connector Terminals Connector Terminals
M2537
M13066
Existed
874
Auxiliary input jacks
GroundContinuity
Connector Terminal
M253 7 Not existed
(+) (−)
Condition Reference value Auxiliary input jacks Auxiliary input jacks
Connector Terminal Connector Terminal
M253 7 M253 8 When AUX image is displayed.
SKIB2251J

AV
REAR VIEW CAMERA POWER SUPPLY
AV-95
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA POWER SUPPLY
DescriptionINFOID:0000000003882757
 Camera control unit outputs camera ON signal to rear view camera and inputs rear view camera image sig-
nal from rear view camera when the reverse signal is input.
 The camera control unit that inputs the camera image signal transmits the camera image signal to the AV
control unit.
Diagnosis ProcedureINFOID:0000000003901214
1.CHECK CONTINUITY CAMERA ON SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector and rear view camera connector.
3. Check continuity between camera control unit harness connector and rear view camera harness connec-
tor.
4. Check continuity between camera control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VOLTAGE CAMERA ON SIGNAL
1. Connect camera control unit connector and rear view camera connector.
2. Turn ignition switch ON.
3. Check signal between camera control unit harness connector and ground.
Is inspection result normal?
YES >> Replace rear view camera.
NO >> Replace camera control unit.
Camera control unit Rear view camera
Continuity
Connector Terminal Connector Terminal
B2518T1031Existed
Camera control unit
GroundContinuity
Connector Terminal
B251 8 Not existed
(+)
(−) ConditionVo l ta g e
(Approx.) Camera control unit
Connector Terminal
B251 8 GroundSelector le-
ver in R posi-
tion. 6.0 V
Other than
selector le-
ver in R posi-
tion. 0 V