ECU NISSAN TEANA 2008 Service Manual

BRC-80
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III FunctionINFOID:0000000003766901
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT
SELF DIAGNOSTIC RESULT
Operation Procedure
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute.
Display Item List
Refer to BRC-140, "DTC No. Index".
How to Erase Self-diagnosis Results
After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
 When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp, VDC
OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is
normal unless the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
 Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake
fluid level switch operation (when brake fluid is insufficient).
 VDC OFF switch should not stay in “ON” position.
DATA MONITOR
Display Item List
×: Applicable : Optional item
Diagnostic test mode Function
Work supportThis mode enables a technician to adjust some devices faster and more accurately by following
the indications on CONSULT-III.
Self diagnostic result Self-diagnostic results can be read and erased quickly.
Data monitor Input/Output data in the ABS actuator and electric unit (control unit) can be read.
Active testCONSULT-III drives some actuators apart from ABS actuator and electric unit (control unit) and
also shifts some parameters in a specified range.
ECU identification ABS actuator and electric unit (control unit) part number can be read.
Item Description
ST ANG SEN ADJUSTMENT Adjusts the neutral position of the steering angle sensor.
Monitor item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN SIGNALS
FR LH SENSOR
[km/h (MPH)]××Wheel speed calculated by front LH wheel sensor signal
FR RH SENSOR
[km/h (MPH)]××Wheel speed calculated by front RH wheel sensor signal
RR LH SENSOR
[km/h (MPH)]××Wheel speed calculated by rear LH wheel sensor signal

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-81
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
RR RH SENSOR
[km/h (MPH)]××Wheel speed calculated by rear RH wheel sensor signal
STOP LAMP SW
(On/Off)××Stop lamp switch signal status
BATTERY VOLT
(V)××Battery voltage supplied to the ABS actuator and electric
unit (control unit)
GEAR××Gear position determined by TCM
OFF SW
(On/Off)××VDC OFF switch
YAW RATE SEN
(d/s)××Yaw rate detected by yaw rate/side G sensor
ACCEL POS SIG
(%)×Throttle actuator opening/closing is displayed
(Linked with accelerator pedal)
SIDE G-SENSOR
(m/s
2)×Transverse G detected by yaw rate/side G sensor
STR ANGLE SIG
(°)×Steering angle detected by steering angle sensor
PRESS SENSOR
(bar)×Brake fluid pressure detected by pressure sensor
ENGINE RPM
[tr/min (rpm)]×Engine speed
FLUID LEV SW
(On/Off)×Brake fluid level switch signal status
PARK BRAKE SW
(On/Off)×Parking brake switch signal status
FR RH IN SOL
(On/Off) (Note 1)×
Operation status of each solenoid valve FR RH OUT SOL
(On/Off) (Note 1)×
FR LH IN SOL
(On/Off) (Note 1)×
FR LH OUT SOL
(On/Off) (Note 1)×
RR RH IN SOL
(On/Off) (Note 1)×
RR RH OUT SOL
(On/Off) (Note 1)×
RR LH IN SOL
(On/Off) (Note 1)×
RR LH OUT SOL
(On/Off) (Note 1)×
MOTOR RELAY
(On/Off)×Motor and motor relay operation
ACTUATOR RLY
(On/Off) (Note 1)×Actuator relay operation
ABS WARN LAMP
(On/Off)×ABS warning lamp
OFF LAMP
(On/Off)×VDC OFF indicator lamp
SLIP LAMP
(On/Off)×SLIP indicator lamp Monitor item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN SIGNALS

BRC-82
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
NOTE:
1: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an
operation for checking.
ACTIVE TEST
CAUTION:
 Do not perform active test while driving vehicle.
 Make sure to completely bleed air from brake system.
 The active test cannot be started when ABS warning lamp, VDC OFF indicator lamp, SLIP indicator
lamp and brake warning lamp are ON.
 ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp are ON
during active test.
NOTE:
 When active test is performed while depressing the pedal, the pedal depression amount will change. This is
normal. (Only solenoid valve and ABS motor.)
 “TEST IS STOPPED” is displayed 10 seconds after operation start.
 After “TEST IS STOPPED” is displayed, to perform test again.
Test Item
ABS SOLENOID VALVE
EBD WARN LAMP
(On/Off)Brake warning lamp
EBD SIGNAL
(On/Off)EBD operation
ABS SIGNAL
(On/Off)ABS operation
TCS SIGNAL
(On/Off)TCS operation
VDC SIGNAL
(On/Off)VDC operation
EBD FAIL SIG
(On/Off)EBD fail-safe signal
ABS FAIL SIG
(On/Off)ABS fail-safe signal
TCS FAIL SIG
(On/Off)TCS fail-safe signal
VDC FAIL SIG
(On/Off)VDC fail-safe signal
CRANKING SIG
(On/Off)Crank operation
USV[FR-RL]
(On/Off) (Note 1)
VDC switch-over valve USV[FL-RR]
(On/Off) (Note 1)
HSV[FR-RL]
(On/Off) (Note 1)
HSV[FL-RR]
(On/Off) (Note 1)
V/R OUTPUT
(On/Off)Solenoid valve relay activated
M/R OUTPUT
(On/Off)Actuator motor and motor relay activated Monitor item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN SIGNALS

BRC-84
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
NOTE:
A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an
operation for checking.
ABS MOTOR Touch “On” and “Off” on screen. Make sure motor relay and actuator relay operates as shown in table below.
NOTE:
A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an
operation for checking.
ECU IDENTIFICATION
ABS actuator and electric unit (control unit) part number can be read.
Test item Display itemDisplay
On Off
ABS MOTORMOTOR RELAY On Off
ACTUATOR RLY (Note) On On

BRC-132
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference ValueINFOID:0000000003767019
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
Monitor item Display contentData monitor
ConditionReference value in
normal operation
FR LH SENSORWheel speed calculated by front LH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
FR RH SENSORWheel speed calculated by front RH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
RR LH SENSORWheel speed calculated by rear LH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
RR RH SENSORWheel speed calculated by rear RH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
STOP LAMP SW Stop lamp switch signal statusWhen brake pedal is depressed On
When brake pedal is not depressed Off
BATTERY VOLTBattery voltage supplied to the ABS ac-
tuator and electric unit (control unit)Ignition switch ON 10 – 16 V
GEAR Gear position determined by TCM1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
other0
1
2
3
4
5
6
7
0
OFF SW VDC OFF switch ON/OFFVDC OFF switch ON
(When VDC OFF indicator lamp is ON)On
VDC OFF switch OFF
(When VDC OFF indicator lamp is OFF)Off
YAW RATE SENYaw rate detected by yaw rate/side G
sensorVehicle stopped Approx. 0 d/s
Vehicle turning right Negative value
Vehicle turning left Positive value
ACCEL POS SIG Throttle actuator opening/closing is
displayed (linked with accelerator ped-
al)Accelerator pedal not depressed
(ignition switch is ON)0 %
Depress accelerator pedal
(ignition switch is ON)0 - 100 %

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-133
< ECU DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
SIDE G-SENSORTransverse G detected by side G sen-
sorVehicle stopped
Approx. 0 m/s
2
Vehicle turning right Negative value
Vehicle turning left Positive value
STR ANGLE SIGSteering angle detected by steering an-
gle sensorDriving straight±2.5°
Turn 90° to right Approx. +90°
Turn 90° to left Approx. –90°
PRESS SENSORBrake fluid pressure detected by pres-
sure sensorWith ignition switch turned ON and brake
pedal releasedApprox. 0 bar
With ignition switch turned ON and brake
pedal depressed–40 to 300 bar
ENGINE RPM With engine runningWith engine stopped 0 rpm
Engine runningAlmost in accor-
dance with tachome-
ter display
FLUID LEV SW Brake fluid level switch signal statusWhen brake fluid level switch ON On
When brake fluid level switch OFF Off
PARK BRAKE SW Parking brake switch signal statusParking brake switch is active On
Parking brake switch is inactive Off
FR RH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR RH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR LH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR LH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
RR RH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
RR RH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off Monitor item Display contentData monitor
ConditionReference value in
normal operation

BRC-134
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RR LH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
RR LH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
MOTOR RELAY Motor and motor relay operationWhen the motor relay and motor are op-
eratingOn
When the motor relay and motor are not
operatingOff
ACTUATOR RLY
(Note 2)Actuator relay operationWhen the actuator relay is operating On
When the actuator relay is not operating Off
ABS WARN LAMPABS warning lamp
(Note 3)When ABS warning lamp is ON On
When ABS warning lamp is OFF Off
EBD WARN LAMPBrake warning lamp
(Note 3)When brake warning lamp is ON On
When brake warning lamp is OFF Off
OFF LAMPVDC OFF indicator lamp
(Note 3)When VDC OFF indicator lamp is ON On
When VDC OFF indicator lamp is OFF Off
SLIP LAMPSLIP indicator lamp
(Note 3)When SLIP indicator lamp is ON On
When SLIP indicator lamp is OFF Off
EBD SIGNAL EBD operationEBD is active On
EBD is inactive Off
ABS SIGNAL ABS operationABS is active On
ABS is inactive Off
TCS SIGNAL TCS operationTCS is active On
TCS is inactive Off
VDC SIGNAL VDC operationVDC is active On
VDC is inactive Off
EBD FAIL SIG EBD fail-safe signalIn EBD fail-safe On
EBD is normal Off
ABS FAIL SIG ABS fail-safe signalIn ABS fail-safe On
ABS is normal Off
TCS FAIL SIG TCS fail-safe signalIn TCS fail-safe On
TCS is normal Off
VDC FAIL SIG VDC fail-safe signalIn VDC fail-safe On
VDC is normal Off
CRANKING SIG Crank operationCrank is active On
Crank is inactive Off Monitor item Display contentData monitor
ConditionReference value in
normal operation

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-135
< ECU DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
NOTE:
 1: Confirm tire pressure is normal.
 2: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an
operation for checking.
 3: On and off timing for warning lamp and indicator lamp.
- ABS warning lamp: Refer to BRC-128, "
Description".
- Brake warning lamp: Refer to BRC-129, "
Description".
- VDC OFF indicator lamp: Refer to BRC-130, "
Description".
- SLIP indicator lamp: Refer to BRC-131, "
Description". USV [FL-RR]
(Note 2)VDC switch-over valveWhen actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)On
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
USV [FR-RL]
(Note 2)VDC switch-over valveWhen actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)On
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
HSV [FL-RR]
(Note 2)VDC switch-over valveWhen actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)On
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
HSV [FR-RL]
(Note 2)VDC switch-over valveWhen actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)On
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
V/R OUTPUT
(Note 2)Solenoid valve relay activatedWhen the solenoid valve relay is active
(When ignition switch OFF)On
When the solenoid valve relay is not ac-
tive (in the fail-safe mode)Off
M/R OUTPUTActuator motor and motor relay activat-
edWhen the actuator motor and motor relay
are active
(“ACTIVE TEST” with CONSULT-III)On
When the actuator motor and motor relay
are inactiveOff Monitor item Display contentData monitor
ConditionReference value in
normal operation

BRC-136
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Wiring Diagram - BRAKE CONTROL SYSTEM -
INFOID:0000000003767020
JCFWM0150GB

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-137
< ECU DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
JCFWM0151GB