Condition NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 2185 of 5121
![NISSAN TEANA 2008 Service Manual EXL-156
< ECU DIAGNOSIS >[XENON TYPE]
AUTO LEVELIZER CONTROL UNIT
AUTO LEVELIZER CONTROL UNIT
Reference ValueINFOID:0000000003805622
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monito NISSAN TEANA 2008 Service Manual EXL-156
< ECU DIAGNOSIS >[XENON TYPE]
AUTO LEVELIZER CONTROL UNIT
AUTO LEVELIZER CONTROL UNIT
Reference ValueINFOID:0000000003805622
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monito](/img/5/57391/w960_57391-2184.png)
EXL-156
< ECU DIAGNOSIS >[XENON TYPE]
AUTO LEVELIZER CONTROL UNIT
AUTO LEVELIZER CONTROL UNIT
Reference ValueINFOID:0000000003805622
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor item Operating conditionDisplay item
(Approx.)
INT SEN VALUE Rear vehicle heightDetection upper limit 100 %
Detection lower limit 0 %
ACT OUTPUT Headlamp light axisControl upper limit 69.8 %
Control lower limit 14.5 %
ACT MEASURED Headlamp light axisDetection upper limit 69.8 %
Detection lower limit 14.5 %
SPEED SIG Vehicle running at approx. 40 km/h (25 MPH) 40 km/h (25 MPH)
LIGHT SIGNAL Tail lampON Battery voltage
OFF 2 V or less
INT SEN VOLT Ignition switchON Battery voltage
Other than ON 0 V
EXT SEN VOLT — —
EXT SEN SIG — —
JPLIA1155ZZ
Te r m i n a l N o .
(Wire color)Description
Operating conditionStandard
(Approx.)
+ - Signal nameInput/
Output
1
(B)Ground Ground — — 0 V
2
(G)Ground Ignition power supply Input Ignition switchON Battery voltage
OFF 0 V
4
(P/W)GroundVehicle speed signal
(8-pulse)InputVehicle running at approx. 40 km/h (25
MPH)
PKIA1935E
Page 2186 of 5121
![NISSAN TEANA 2008 Service Manual AUTO LEVELIZER CONTROL UNIT
EXL-157
< ECU DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
*: Auto levelizer control unit always outputs the voltage to detect the DTC.5
(O)Ground K-LINE — NISSAN TEANA 2008 Service Manual AUTO LEVELIZER CONTROL UNIT
EXL-157
< ECU DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
*: Auto levelizer control unit always outputs the voltage to detect the DTC.5
(O)Ground K-LINE —](/img/5/57391/w960_57391-2185.png)
AUTO LEVELIZER CONTROL UNIT
EXL-157
< ECU DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
*: Auto levelizer control unit always outputs the voltage to detect the DTC.5
(O)Ground K-LINE — — —
6
(R/L)Ground Tail lamp signal Input Tail lampON Battery voltage
OFF 2 V or less*
7
(G/Y)GroundHeadlamp aiming
motor drive signalOutput Headlamp aimingUnder unladen
conditions8.7 V
At aiming operation
lower limit1.8 V Te r m i n a l N o .
(Wire color)Description
Operating conditionStandard
(Approx.)
+ - Signal nameInput/
Output
Page 2196 of 5121
![NISSAN TEANA 2008 Service Manual NORMAL OPERATING CONDITION
EXL-167
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000003774368
XENON HEADLAMP
Brightness and the NISSAN TEANA 2008 Service Manual NORMAL OPERATING CONDITION
EXL-167
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000003774368
XENON HEADLAMP
Brightness and the](/img/5/57391/w960_57391-2195.png)
NORMAL OPERATING CONDITION
EXL-167
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000003774368
XENON HEADLAMP
Brightness and the color of light may change slightly immediately after turning the headlamp ON until the
xenon bulb becomes stable. This is normal.
Illumination time lag may occur between right and left. This is normal.
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes for the control difference. This
is normal.
Page 2197 of 5121
![NISSAN TEANA 2008 Service Manual EXL-168
< SYMPTOM DIAGNOSIS >[XENON TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
DescriptionINFOID:0000000003774369
Both side headlamps (HI) are not turn NISSAN TEANA 2008 Service Manual EXL-168
< SYMPTOM DIAGNOSIS >[XENON TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
DescriptionINFOID:0000000003774369
Both side headlamps (HI) are not turn](/img/5/57391/w960_57391-2196.png)
EXL-168
< SYMPTOM DIAGNOSIS >[XENON TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
DescriptionINFOID:0000000003774369
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis ProcedureINFOID:0000000003774370
1.COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to BCS-76, "
Symptom Table".
Is the combination switch normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “HL HI REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the item status normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
3.HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to EXL-54, "
Component Function Check".
Is the headlamp (HI) circuit normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
Monitor item Condition Monitor status
HL HI REQLighting switch
(2ND)HI or PASS On
LO Off
Page 2198 of 5121
![NISSAN TEANA 2008 Service Manual BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-169
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
DescriptionINFOID:0000000003774371
Both NISSAN TEANA 2008 Service Manual BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-169
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
DescriptionINFOID:0000000003774371
Both](/img/5/57391/w960_57391-2197.png)
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-169
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
DescriptionINFOID:0000000003774371
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis ProcedureINFOID:0000000003774372
1.CHECK COMBINATION SWITCH
Check the combination switch. Refer to BCS-76, "
Symptom Table".
Is the combination switch normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “HL LO REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the item status normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
3.HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to EXL-56, "
Component Function Check".
Is the headlamp (LO) circuit normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
Monitor item Condition Monitor status
HL LO REQ Lighting switch2ND On
OFF Off
Page 2199 of 5121
![NISSAN TEANA 2008 Service Manual EXL-170
< SYMPTOM DIAGNOSIS >[XENON TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773608
The parking NISSAN TEANA 2008 Service Manual EXL-170
< SYMPTOM DIAGNOSIS >[XENON TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773608
The parking](/img/5/57391/w960_57391-2198.png)
EXL-170
< SYMPTOM DIAGNOSIS >[XENON TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773608
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
Diagnosis ProcedureINFOID:0000000003773609
1.CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> GO TO 2.
2.COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to BCS-76, "
Symptom Table".
Is the combination switch normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the item status normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
4.TAIL LAMP CIRCUIT INSPECTION
Check the tail lamp circuit. Refer to EXL-74, "
Component Function Check".
Is the tail lamp circuit normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
Unit Location Fuse No. Capacity
Parking lamp
IPDM E/R#52 10 A
Tail lamp
License plate lamp#53 10 A
Monitor item Condition Monitor status
TAIL & CLR
REQLighting switch1ST On
OFF Off
Page 2200 of 5121
![NISSAN TEANA 2008 Service Manual BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-171
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773610
Th NISSAN TEANA 2008 Service Manual BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-171
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773610
Th](/img/5/57391/w960_57391-2199.png)
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-171
< SYMPTOM DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
DescriptionINFOID:0000000003773610
The front fog lamps are not turned ON in any condition.
Diagnosis ProcedureINFOID:0000000003773611
1.CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> GO TO 2.
2.COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to BCS-76, "
Symptom Table".
Is the combination switch normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
4.FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to EXL-62, "
Component Function Check".
Is the front fog lamp circuit normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #58 15 A
Monitor item Condition Monitor status
FR FOG REQFront fog lamp switch
(With lighting switch 1ST)ON On
OFF Off
Page 2201 of 5121
![NISSAN TEANA 2008 Service Manual EXL-172
< PRECAUTION >[XENON TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003813382
The Supplement NISSAN TEANA 2008 Service Manual EXL-172
< PRECAUTION >[XENON TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003813382
The Supplement](/img/5/57391/w960_57391-2200.png)
EXL-172
< PRECAUTION >[XENON TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003813382
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precautions For Xenon Headlamp ServiceINFOID:0000000003773614
WARNING:
Comply with the following warnings to prevent any serious accident.
Disconnect the battery cable (negative terminal) or the power supply fuse before installing, remov-
ing, or touching the xenon headlamp (bulb included). The xenon headlamp contains high-voltage
generated parts.
Never work with wet hands.
Check the xenon headlamp ON-OFF status after assembling it to the vehicle. Never turn the xenon
headlamp ON in other conditions. Connect the power supply to the vehicle-side connector.
(Turning it ON outside the lamp case may cause fire or visual impairments.)
Never touch the bulb glass immediately after turning it OFF. It is extremely hot.
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-
tor, the housing, etc. by high-voltage leakage or corona discharge.)
Never perform HID circuit inspection with a tester.
Never touch the xenon bulb glass with hands. Never put oil and grease on it.
Dispose of the used xenon bulb after packing it in thick vinyl without breaking it.
Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).
Page 2202 of 5121
![NISSAN TEANA 2008 Service Manual HEADLAMP AIMING ADJUSTMENT
EXL-173
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003774534
PREPARAT NISSAN TEANA 2008 Service Manual HEADLAMP AIMING ADJUSTMENT
EXL-173
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003774534
PREPARAT](/img/5/57391/w960_57391-2201.png)
HEADLAMP AIMING ADJUSTMENT
EXL-173
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003774534
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following. Adjust the tire pressure to the specification.
Fill with fuel, engine coolant and each oil.
Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JPLIA1085ZZ
Page 2207 of 5121
![NISSAN TEANA 2008 Service Manual EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, re NISSAN TEANA 2008 Service Manual EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, re](/img/5/57391/w960_57391-2206.png)
EXL-178
< ON-VEHICLE MAINTENANCE >[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
DescriptionINFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
Adjust the tire pressure to the specification.
Fill with fuel, engine coolant and each oil.
Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Turn the aiming adjusting screw for adjustment.
For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment ProcedureINFOID:0000000003773618
1. Place the screen.
NOTE:
Stop the vehicle facing the wall.
Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA1086ZZ
JPLIA0008ZZ