display NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 4083 of 5121
![NISSAN TEANA 2008 Service Manual SEC-74
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B2609 STEERING STATUS
B2609 STEERING STATUS
DescriptionINFOID:0000000003814999
There are 2 switches in the steering lock unit (steering lock/unlo NISSAN TEANA 2008 Service Manual SEC-74
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B2609 STEERING STATUS
B2609 STEERING STATUS
DescriptionINFOID:0000000003814999
There are 2 switches in the steering lock unit (steering lock/unlo](/img/5/57391/w960_57391-4082.png)
SEC-74
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B2609 STEERING STATUS
B2609 STEERING STATUS
DescriptionINFOID:0000000003814999
There are 2 switches in the steering lock unit (steering lock/unlock switch 1 and 2). BCM compares those 2
switches conditions to judge the present steering status.
DTC LogicINFOID:0000000003815000
DTC DETECTION LOGIC
NOTE:
If DTC B2609 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B2609 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE 1
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-74, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE 2
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Press driver side door switch and wait for at least 1 second.
4. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-74, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815001
1.INSPECTION START
Check the case in which DTC is detected.
Case1: It is detected after ignition switch is changed from OFF to ON
Case2: It is detected after ignition switch is changed from ON to OFF and door switch is pressed
In which case is DTC detected?
Case1 >> GO TO 2.
Case2 >> GO TO 6.
2.CHECK BCM OUTPUT SIGNAL
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2609 STEERING STATUSBCM detects the malfunction of steering lock unit
switches for 1 second. Harness or connectors
[Steering lock unit circuit (BCM
side) is open or shorted]
Harness or connectors
[Steering lock unit circuit (IPDM E/
R side) is open or shorted]
Steering lock unit
IPDM E/R
BCM
Page 4087 of 5121
![NISSAN TEANA 2008 Service Manual SEC-78
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260B STEERING LOCK UNIT
B260B STEERING LOCK UNIT
DescriptionINFOID:0000000003815002
The steering lock unit performs the check by itself accordin NISSAN TEANA 2008 Service Manual SEC-78
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260B STEERING LOCK UNIT
B260B STEERING LOCK UNIT
DescriptionINFOID:0000000003815002
The steering lock unit performs the check by itself accordin](/img/5/57391/w960_57391-4086.png)
SEC-78
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260B STEERING LOCK UNIT
B260B STEERING LOCK UNIT
DescriptionINFOID:0000000003815002
The steering lock unit performs the check by itself according to the steering status.
DTC LogicINFOID:0000000003815003
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch, when steering is locked.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-78, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815004
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-78, "
DTC Logic".
Is the DTC B260B displayed again?
YES >> Replace steering lock unit.
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B260B STEERING LOCK UNITBCM detects malfunctioning of steering lock unit be-
fore steering unlocking.Steering lock unit
Page 4088 of 5121
![NISSAN TEANA 2008 Service Manual B260C STEERING LOCK UNIT
SEC-79
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260C STEERING LOCK UNIT
DescriptionINFOID:0000000003815005
The steering lock unit perf NISSAN TEANA 2008 Service Manual B260C STEERING LOCK UNIT
SEC-79
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260C STEERING LOCK UNIT
DescriptionINFOID:0000000003815005
The steering lock unit perf](/img/5/57391/w960_57391-4087.png)
B260C STEERING LOCK UNIT
SEC-79
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260C STEERING LOCK UNIT
DescriptionINFOID:0000000003815005
The steering lock unit performs the check by itself according to the steering status.
DTC LogicINFOID:0000000003815006
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Press driver side door switch.
4. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-79, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815007
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-79, "
DTC Logic".
Is the DTC B260C displayed again?
YES >> Replace steering lock unit.
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B260C STEERING LOCK UNITBCM detects malfunctioning of steering lock unit be-
fore steering locking.Steering lock unit
Page 4089 of 5121
![NISSAN TEANA 2008 Service Manual SEC-80
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260D STEERING LOCK UNIT
B260D STEERING LOCK UNIT
DescriptionINFOID:0000000003815008
The steering lock unit performs the check by itself accordin NISSAN TEANA 2008 Service Manual SEC-80
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260D STEERING LOCK UNIT
B260D STEERING LOCK UNIT
DescriptionINFOID:0000000003815008
The steering lock unit performs the check by itself accordin](/img/5/57391/w960_57391-4088.png)
SEC-80
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B260D STEERING LOCK UNIT
B260D STEERING LOCK UNIT
DescriptionINFOID:0000000003815008
The steering lock unit performs the check by itself according to the steering lock status (before lock, after lock
and unlock).
DTC LogicINFOID:0000000003815009
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Press driver side door switch.
4. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-80, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815010
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-80, "
DTC Logic".
Is the DTC B260D displayed again?
YES >> Replace steering lock unit.
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B260D STEERING LOCK UNITBCM detects malfunctioning of steering lock unit after
steering locking.Steering lock unit
Page 4090 of 5121
![NISSAN TEANA 2008 Service Manual B260F ENGINE STATUS
SEC-81
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260F ENGINE STATUS
DescriptionINFOID:0000000003815011
BCM receives the engine status signal NISSAN TEANA 2008 Service Manual B260F ENGINE STATUS
SEC-81
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260F ENGINE STATUS
DescriptionINFOID:0000000003815011
BCM receives the engine status signal](/img/5/57391/w960_57391-4089.png)
B260F ENGINE STATUS
SEC-81
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B260F ENGINE STATUS
DescriptionINFOID:0000000003815011
BCM receives the engine status signal from ECM via CAN communication.
DTC LogicINFOID:0000000003815012
DTC DETECTION LOGIC
NOTE:
If DTC B260F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B260F is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-81, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815013
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-81, "
DTC Logic".
Is the DTC B260F displayed again?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPLACE ECM
Replace ECM. Refer to EC-14, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
>> INSPECTION END
3.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B260F INTERRUPTION OF ENGINE STATUS SIGNALBCM has not yet received the engine status sig-
nal from ECM when ignition switch is in the ON
positionECM
Page 4091 of 5121
![NISSAN TEANA 2008 Service Manual SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine NISSAN TEANA 2008 Service Manual SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine](/img/5/57391/w960_57391-4090.png)
SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine status signal from ECM via CAN communication.
DTC LogicINFOID:0000000003815015
DTC DETECTION LOGIC
NOTE:
If DTC B26E1 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B26E1 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-82, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815016
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-82, "
DTC Logic".
Is the DTC B26E1 displayed again?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPLACE ECM
Replace ECM. Refer to EC-14, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
>> INSPECTION END
3.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B26E1 NO RECEPTION OF ENGINE STATUS SIGNALBCM does not receive the engine status signal
from ECM when ignition switch is in the ON po-
sitionECM
Page 4092 of 5121
![NISSAN TEANA 2008 Service Manual B26E9 STEERING STATUS
SEC-83
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B26E9 STEERING STATUS
DescriptionINFOID:0000000003815017
There are 2 switches in the steer NISSAN TEANA 2008 Service Manual B26E9 STEERING STATUS
SEC-83
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B26E9 STEERING STATUS
DescriptionINFOID:0000000003815017
There are 2 switches in the steer](/img/5/57391/w960_57391-4091.png)
B26E9 STEERING STATUS
SEC-83
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B26E9 STEERING STATUS
DescriptionINFOID:0000000003815017
There are 2 switches in the steering lock unit (steering lock/unlock switch 1 and 2). BCM compares those 2
switches conditions to judge the present steering status.
DTC LogicINFOID:0000000003815018
DTC DETECTION LOGIC
NOTE:
If DTC B26E9 is displayed with DTC B2609, first perform the trouble diagnosis for DTC B2609. Refer to
SEC-74, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Press driver side door switch and wait for at least 1 second.
4. Turn ignition switch ON.
5. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SEC-83, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815019
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC Confirmation Procedure.
Refer to SEC-83, "
DTC Logic".
Is the DTC B26E9 displayed again?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPLACE STEERING LOCK UNIT
1. Replace steering lock unit.
2. Perform DTC confirmation procedure. Refer to SEC-83, "
DTC Logic".
Is the DTC B26E9 displayed again?
YES >> GO TO 3.
NO >> INSPECTION END
3.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B26E9 S/L STATUSBCM requests lock to steering lock unit, then steer-
ing lock unit transmits a recognition signal to BCM,
but steering lock unit remains unlocked.Steering lock unit
Page 4094 of 5121
![NISSAN TEANA 2008 Service Manual B2612 STEERING STATUS
SEC-85
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2612 STEERING STATUS
DescriptionINFOID:0000000003815023
There are 2 switches in the steer NISSAN TEANA 2008 Service Manual B2612 STEERING STATUS
SEC-85
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2612 STEERING STATUS
DescriptionINFOID:0000000003815023
There are 2 switches in the steer](/img/5/57391/w960_57391-4093.png)
B2612 STEERING STATUS
SEC-85
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2612 STEERING STATUS
DescriptionINFOID:0000000003815023
There are 2 switches in the steering lock unit. IPDM E/R compares those 2 switch conditions to judge the
present steering status and transmit the result to BCM via CAN communication.
DTC LogicINFOID:0000000003815024
DTC DETECTION LOGIC
NOTE:
If DTC B2612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B2612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE 1
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-85, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE 2
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Press door switch.
4. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-85, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815025
1.INSPECTION START
Check the case in which DTC is detected.
Case1: It is detected after ignition switch is changed from OFF to ON
Case2: It is detected after ignition switch is changed from ON to OFF and door switch is pressed
In which case is DTC detected?
Case1 >> GO TO 2.
Case2 >> GO TO 6.
2.CHECK BCM OUTPUT SIGNAL
1. Turn ignition switch OFF.
DTC Self-diagnosis name DTC detecting condition Possible causes
B2612 STEERING STATUSBCM detects the difference between
the following status for 1 second
Steering lock or unlock
Feedback of steering lock status from
IPDM E/R (CAN) Harness or connectors
[Steering lock unit circuit (BCM side) is
open or shorted]
Harness or connectors
[Steering lock unit circuit (IPDM E/R side)
is open or shorted]
Steering lock unit
IPDM E/R
BCM
Page 4098 of 5121
![NISSAN TEANA 2008 Service Manual B2617 STARTER RELAY CIRCUIT
SEC-89
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2617 STARTER RELAY CIRCUIT
DescriptionINFOID:0000000003815026
Located in IPDM E/R, NISSAN TEANA 2008 Service Manual B2617 STARTER RELAY CIRCUIT
SEC-89
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2617 STARTER RELAY CIRCUIT
DescriptionINFOID:0000000003815026
Located in IPDM E/R,](/img/5/57391/w960_57391-4097.png)
B2617 STARTER RELAY CIRCUIT
SEC-89
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2617 STARTER RELAY CIRCUIT
DescriptionINFOID:0000000003815026
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in the START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communica-
tion.
DTC LogicINFOID:0000000003815027
DTC DETECTION LOGIC
NOTE:
If DTC B2617 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B2617 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
If DTC B2617 is displayed with DTC B2611, first perform the trouble diagnosis for DTC B2611. Refer to
SEC-89, "
DTC Logic".
If DTC B2617 is displayed with DTC B210E for IPDM E/R, first perform the trouble diagnosis for DTC
B210E. Refer to SEC-105, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-89, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815028
1.CHECK STARTER RELAY
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK STARTER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and BCM harness connector.
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2617STARTER RELAY
CIRCUITAn immediate operation of starter relay is request-
ed by BCM, but there is no response for more than
1 second Harness or connectors
(Starter relay circuit is open or short-
ed)
IPDM E/R
(+)
(–) ConditionVoltage (V)
(Approx.) BCM
Connector Terminal
M121 52 Ground Selector leverN or P position Battery voltage
Other than above 0
Page 4100 of 5121
![NISSAN TEANA 2008 Service Manual B2619 BCM
SEC-91
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2619 BCM
DescriptionINFOID:0000000003815029
BCM requests IPDM E/R to supply power to steering lock un NISSAN TEANA 2008 Service Manual B2619 BCM
SEC-91
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2619 BCM
DescriptionINFOID:0000000003815029
BCM requests IPDM E/R to supply power to steering lock un](/img/5/57391/w960_57391-4099.png)
B2619 BCM
SEC-91
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B2619 BCM
DescriptionINFOID:0000000003815029
BCM requests IPDM E/R to supply power to steering lock unit. After receiving the power, the steering lock unit
transmits an ON signal to BCM.
DTC LogicINFOID:0000000003815030
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-91, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815031
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-91, "
DTC Logic".
Is the DTC B2619 displayed again?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B2619 BCMBCM detects a mismatch between the power supplied to the
steering lock unit and the feedback for one second or more.BCM