display NISSAN TEANA 2014 User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 69 of 4801
![NISSAN TEANA 2014 User Guide
BCS-54
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
C1712: [CHECKSUM ERR] FL — —
×
WT-33, "DTC Logic"
C1713: [CHECKSUM ERR] FR — — ×
C1714: [CHECKSUM ERR] RR — — ×
C171](/img/5/57390/w960_57390-68.png "NISSAN TEANA 2014 User Guide
BCS-54
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
C1712: [CHECKSUM ERR] FL — —
×
WT-33, \"DTC Logic\"
C1713: [CHECKSUM ERR] FR — — ×
C1714: [CHECKSUM ERR] RR — — ×
C171")
BCS-54
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
C1712: [CHECKSUM ERR] FL — —
×
WT-33, "DTC Logic"
C1713: [CHECKSUM ERR] FR — — ×
C1714: [CHECKSUM ERR] RR — — ×
C1715: [CHECKSUM ERR] RL — — ×
C1716: [PRESSDATA ERR] FL — — ×
WT-35, "DTC Logic"
C1717: [PRESSDATA ERR] FR — — ×
C1718: [PRESSDATA ERR] RR — — ×
C1719: [PRESSDATA ERR] RL — — ×
C1720: [CODE ERR] FL — — ×
WT-37, "DTC Logic"
C1721: [CODE ERR] FR — — ×
C1722: [CODE ERR] RR — — ×
C1723: [CODE ERR] RL — — ×
C1724: [BATT VOLT LOW] FL — — ×
WT-39, "DTC Logic"
C1725: [BATT VOLT LOW] FR — — ×
C1726: [BATT VOLT LOW] RR — — ×
C1727: [BATT VOLT LOW] RL — — ×
C1729: VHCL SPEED SIG ERR — — ×WT-41, "DTC Logic"
C1730: FLAT TIRE FL — — ×
WT-42, "DTC Logic"
C1731: FLAT TIRE FR — — ×
C1732: FLAT TIRE RR — — ×
C1733: FLAT TIRE RL — — ×
C1734: CONTROL UNIT — — ×WT-44, "DTC Logic"
C1735: IGNTION SIGNAL — — ×WT-46, "DTC Logic"
CONSULT display Fail-safe Intelligent Key
warning lamp
ON Tire pressure
monitor warning
lamp ON Reference page
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 79 of 4801
![NISSAN TEANA 2014 User Guide
BCS-64
< BASIC INSPECTION >[BCM]
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPL ACING CONTROL UNIT :](/img/5/57390/w960_57390-78.png "NISSAN TEANA 2014 User Guide
BCS-64
< BASIC INSPECTION >[BCM]
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPL ACING CONTROL UNIT :")
BCS-64
< BASIC INSPECTION >[BCM]
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPL ACING CONTROL UNIT : Description
INFOID:0000000009462021
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle s pecification with CONSULT configuration before replace-
ment.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing BCM.
AFTER REPLACEMENT
CAUTION:
• When replacing BCM, you must perfo rm “After Replace ECU” with CONSULT.
- Complete the procedure of “After Replace ECU” in order.
- If you set incorrect “After Replace ECU”, incidents might occur.
- Configuration is different for each vehicle mode l. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLAC ING CONTROL UNIT : Work Procedure
INFOID:0000000009462022
1.SAVING VEHICLE SPECIFICATION
CONSULT
Enter "Re/Programming, Configuration" and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the "After Replace ECU" or "Manual Configuration" after replac-
ing BCM.
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-80, "Removal and Installation"
.
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT
1. Enter "Re/Programming, Configuration".
2. If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "S aved Data List" and press “Confirm” to write vehicle
specification. Refer to BCS-65, "CONFIGURATION (BCM) : Work Procedure"
.
3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to BCS-65, "CONFIGURATION (BCM) : Work Procedure"
.
>> GO TO 4.
4.INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> Work End.
CONFIGURATION (BCM)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 83 of 4801
![NISSAN TEANA 2014 User Guide
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, "BODY CONTROL SYST EM : System Descriptio](/img/5/57390/w960_57390-82.png "NISSAN TEANA 2014 User Guide
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, \"BODY CONTROL SYST EM : System Descriptio")
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, "BODY CONTROL SYST EM : System Description".
DTC LogicINFOID:0000000009462029
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a pr esent DTC by performing the Self Diagnostic Result
procedure.
Diagnosis ProcedureINFOID:0000000009462030
1. PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “SELF- DIAG RESULTS”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Perform CAN Diagnosis as described in DIAG NOSIS section of CONSULT Operation Manual.
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detectio n Condition Possible cause
CAN COMM CIRCUIT
[U1000] When any listed module cannot communicate with CAN
communication signal continuously for 2 seconds or
more with ignition switch ON In CAN communication system, any item (or items)
of the following listed below is malfunctioning.
•Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 84 of 4801
![NISSAN TEANA 2014 User Guide
BCS
U1010 CONTROL UNIT (CAN)BCS-69
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000009462031
DTC DETECTION LOGIC
Diagnosis ProcedureINF](/img/5/57390/w960_57390-83.png "NISSAN TEANA 2014 User Guide
BCS
U1010 CONTROL UNIT (CAN)BCS-69
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000009462031
DTC DETECTION LOGIC
Diagnosis ProcedureINF")
BCS
U1010 CONTROL UNIT (CAN)BCS-69
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000009462031
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000009462032
1. REPLACE BCM
When DTC U1010 is detected, replace BCM.
>> Replace BCM. Refer to BCS-80, "Removal and Installation"
.
CONSULT Display DTC Detectio n Condition Possible Cause
CAN COMM CIRCUIT
[U1010] BCM detected internal CAN communication circuit mal-
function. BCM
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 85 of 4801
![NISSAN TEANA 2014 User Guide
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception statu](/img/5/57390/w960_57390-84.png "NISSAN TEANA 2014 User Guide
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception statu")
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC LogicINFOID:0000000009462034
DTC DETECTION LOGIC
NOTE:
• If DTC U0415 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-68, "DTC Logic"
.
• If DTC U0415 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-69, "DTC Logic"
.
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase the DTC.
2. Turn ignition switch OFF.
3. Perform Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON for 2 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-52, "DTC Index".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462035
1. ABS ACTUATOR AND ELECTRIC UNIT (CON TROL UNIT) SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of ABS with CONSULT. Refer to BRC-33, "CONSULT Function (ABS)"
.
Is any DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to BRC-45, "DTC Index".
NO >> GO TO 2.
2. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Check ABS actuator and electric unit (control unit) power and ground. Refer to BRC-70, "Diagnosis Proce-
dure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. COMBINATION METER SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of METER M&A with CONSULT. Refer to MWI-18, "CONSULT Function
(METER/M&A)".
Is any DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to MWI-27, "DTC Index".
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detectio n Condition Possible Cause
VEHICLE SPEED SIG
[U0415] When the vehicle speed signal received from the
ABS actuator and electric unit (control unit) remains
abnormal for 2 seconds or more. • ABS system
• Combination meter system
• CAN bus harness
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 86 of 4801
![NISSAN TEANA 2014 User Guide
BCS
B2562 LOW VOLTAGEBCS-71
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2562 LOW VOLTAGE
DTC LogicINFOID:0000000009462036
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC C](/img/5/57390/w960_57390-85.png "NISSAN TEANA 2014 User Guide
BCS
B2562 LOW VOLTAGEBCS-71
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2562 LOW VOLTAGE
DTC LogicINFOID:0000000009462036
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC C")
BCS
B2562 LOW VOLTAGEBCS-71
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2562 LOW VOLTAGE
DTC LogicINFOID:0000000009462036
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the Self Diagnostic Result of BCM with CO NSULT, after the ignition switch has been turned ON
for 120 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-71, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462037
1. CHECK BATTERY VOLTAGE
Check battery voltage.
Is battery voltage less than 8.8V?
YES >> Charge battery and retest. Refer to CHG-17, "Work Flow (With EXP-800 NI or GR8-1200 NI)" or
CHG-20, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
.
NO >> GO TO 2.
2. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to BCS-74, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. BCM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of BCM with CONSULT. Refer to BCS-25, "BCM : CONSULT Function (BCM -
BCM)".
Is DTC B2562 CRNT?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detection Condition Possible cause
LOW VOLTAGE
[B2562] When the power supply voltage to BCM remains less
than 8.8V for 120 seconds or more • Harness or connector (power supply circuit)
• Vehicle battery
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 87 of 4801
![NISSAN TEANA 2014 User Guide
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2.](/img/5/57390/w960_57390-86.png "NISSAN TEANA 2014 User Guide
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2.")
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON for 2 minutes or more.
Is any DTC detected?
YES >> Refer to BCS-72, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462039
Regarding Wiring Diagram information, refer to BCS-55, "Wiring Diagram".
1. CHECK FUSE
Check that the following fuse is not blown.
Is the fuse or fusible link blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2. CHECK BAT BCM FUSE CIRCUIT
1. Disconnect BCM connector M21.
2. Check voltage between BCM connector M21 terminal 131 and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Repair or replace harness or connectors. GO TO 3.
3. CHECK BATTERY SAVER OUTPUT CIRCUIT FOR SHORT TO GROUND
1. Turn ignition OFF.
2. Check continuity between BCM connector M21 terminal 129 and ground.
CONSULT Display DTC Detectio n Condition Possible cause
ROOM LAMP FUSE
[B259A] When BCM detects that power supply voltage is sup-
plied to fusible link battery power, but not to BCM bat-
tery fuse for 2 minutes when ignition switch is ON. Harness or connector (power supply circuit)
Terminal No. Signal name Fuse No.
131 BCM battery fuse 1 (10A)
BCM GroundVo l ta g e
(Approx.)
Connector Terminal
M21 131 — Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 179 of 4801
![NISSAN TEANA 2014 User Guide
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-33
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CO](/img/5/57390/w960_57390-178.png "NISSAN TEANA 2014 User Guide
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-33
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CO")
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-33
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT Function (ABS)INFOID:0000000009463758
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentiall y causing a discharged battery and a no-start condition.
FUNCTION
CONSULT can display each diagnostic item us ing the following direct diagnostic modes.
ECU IDENTIFICATION
ABS actuator and electric unit (control unit) part number is displayed.
SELF DIAGNOSTIC RESULT
Operation Procedure
1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How To Erase Self Diagnostic Result
1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute as the final inspection, and make sure t hat the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp,
SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is normal, unless
the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid
level switch operation (when brake fluid is insufficient).
• VDC OFF switch should not stay in ON position.
Display Item List
Refer to BRC-45, "DTC Index".
DATA MONITOR
Direct Diagnostic Mode Description
ECU identification The ABS actuator and electric un it (control unit) part number is displayed.
Self Diagnostic Result The ABS actuator and electric unit (control unit) self diagnostic results are displayed.
Data Monitor The ABS actuator and elec tric unit (control unit) input/output data is displayed in real time.
Active Test The ABS actuator and elec tric unit (control unit) activates outputs to test components.
Work support The settings for ABS actuator and electric unit (control unit) functions can be changed.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
Configuration • Read and save the vehicle specification (TYPE ID).
• Write the vehicle specification (TYPE ID) when replacing ABS actu ator and electric unit (con-
trol unit).
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 180 of 4801
![NISSAN TEANA 2014 User Guide
BRC-34
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION](/img/5/57390/w960_57390-179.png "NISSAN TEANA 2014 User Guide
BRC-34
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION")
BRC-34
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
FR LH SENSOR
(km/h, mph) ×× × Wheel speed (km/h, mph) calculated by front wheel
sensor LH signal is displayed.
FR RH SENSOR
(km/h, mph) ×× × Wheel speed (km/h, mph) calculated by front wheel
sensor RH signal is displayed.
RR LH SENSOR
(km/h, mph) ×× ×
Wheel speed (km/h, mph) calculated by rear wheel
sensor LH signal is displayed.
RR RH SENSOR
(km/h, mph) ×× × Wheel speed (km/h, mph) calculated by rear wheel
sensor RH signal is displayed.
DECEL G-SEN
(G) ×× × Longitudinal acceleration (G) detected by decel G-
sensor is displayed.
FR RH IN SOL
(On/Off) –
×× Front RH IN ABS solenoid (On/Off) status is dis-
played.
FR RH OUT SOL
(On/Off) –
×× Front RH OUT ABS solenoid (On/Off) status is dis-
played.
FR LH IN SOL
(On/Off) –
×× Front LH IN ABS solenoid (On/Off) status is displayed.
FR LH OUT SOL
(On/Off) –
×× Front LH OUT ABS solenoid (On/Off) status is dis-
played.
RR RH IN SOL
(On/Off) –
×× Rear RH IN ABS solenoid (On/ Off) status is displayed.
RR RH OUT SOL
(On/Off) –
×× Rear RH OUT ABS solenoid (On/Off) status is dis-
played.
RR LH IN SOL
(On/Off) –
×× Rear LH IN ABS solenoid (On/ Off) status is displayed.
RR LH OUT SOL
(On/Off) –
×× Rear LH OUT ABS solenoid (On/Off) status is dis-
played.
EBD WARN LAMP
(On/Off) ––
×Brake warning lamp (On/Off) status is displayed.
STOP LAMP SW
(On/Off) ×× ×
Stop lamp switch (On/Off) status is displayed.
MOTOR RELAY
(On/Off) –
×× ABS motor relay signal (On/Of f) status is displayed.
ACTUATOR RLY
(On/Off) –
×× ABS actuator relay signal (On/ Off) status is displayed.
ABS WARN LAMP
(On/Off) –
×× ABS warning lamp (On/Off) status is displayed.
OFF LAMP
(On/Off) –
×× VDC OFF Lamp (On/Off) status is displayed.
SLIP/VDC LAMP
(On/Off) –
×× SLIP indicator lamp (On/Off) status is displayed.
BATTERY VOLT
(V) ×× × Voltage (V) supplied to ABS actuator and electric unit
(control unit) is displayed.
GEAR
(1, 2, 3, 4, 5) ×× ×
Gear position (1, 2, 3, 4, 5) judged by transmission
range switch signal is displayed.
SLCT LVR POSI ×× × Current gear position judged from current gear posi-
tion signal is displayed.
YAW R AT E S E N
(d/s) ×× × Yaw rate (d/s) detected by yaw rate sensor is dis-
played.
R POSI SIG
(On/Off) ––
×Reverse shift position (On/Off) judged by transmis-
sion range switch signal.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 181 of 4801
![NISSAN TEANA 2014 User Guide
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-35
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
× : Applicable
–: Not applicable N POSI SIG
(On/O](/img/5/57390/w960_57390-180.png "NISSAN TEANA 2014 User Guide
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-35
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
× : Applicable
–: Not applicable N POSI SIG
(On/O")
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-35
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
× : Applicable
–: Not applicable N POSI SIG
(On/Off) ––
×Neutral position (On/Off) judged by transmission
range switch signal.
P POSI SIG
(On/Off) ––
×Park position (On/Off) judged by transmission range
switch signal.
ACCEL POS SIG
(%) ×
– ×Throttle valve open/close status judged by CAN com-
munication signal is displayed.
SIDE G-SENSOR
(m/s
2) ×
– ×Transverse acceleration detected by side G-sensor is
displayed.
STR ANGLE SIG
(deg) ×
– ×Steering angle detected by steering angle sensor is
displayed.
PRESS SENSOR
(bar) ×
– ×Brake pressure detected by pressure sensor is dis-
played.
EBD SIGNAL
(On/Off) ––
×EBD operation (On/Off) status is displayed.
ABS SIGNAL
(On/Off) ––
×ABS operation (On/Off) status is displayed.
TCS SIGNAL
(On/Off) ––
×TCS operation (On/Off) status is displayed.
VDC SIGNAL
(On/Off) ––
×VDC operation (On/Off) status is displayed.
EBD FAIL SIG
(On/Off) ––
×EBD fail signal (On/Off) status is displayed.
ABS FAIL SIG
(On/Off) ––
×ABS fail signal (On/Off) status is displayed.
TCS FAIL SIG
(On/Off) ––
×TCS fail signal (On/Off) status is displayed.
VDC FAIL SIG
(On/Off) ––
×VDC fail signal (On/Off) status is displayed.
CRANKING SIG
(On/Off) ––
×The input state of the key SW START position signal
is displayed.
FLUID LEV SW
(On/Off) ×
– ×Brake fluid level switch (On/Off) status is displayed.
PARK BRAKE SW
(On/Off) ×
– ×Park brake switch (On/Off) status is displayed.
USV[FL-RR]
(On/Off) ——
×Primary side USV solenoid valve (On/Off) status is
displayed.
USV[FR-RL]
(On/Off) ——
×Secondary side USV solenoid valve (On/Off) status is
displayed.
HSV[FL-RR]
(On/Off) ——
×Primary side HSV solenoid valve (On/Off) status is
displayed.
HSV[FR-RL]
(On/Off) ——
×Secondary side HSV solenoid valve (On/Off) status is
displayed.
V/R OUTPUT
(On/Off) ——
×Valve relay operation signal (On/Off) status is dis-
played.
M/R OUTPUT
(On/Off) ——
×Motor relay operation signal (On/Off) status is dis-
played.
ENGINE RPM
(tr/min) ×
– ×Engine speed judged by CAN communication signal
is displayed.
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM