Pressure NISSAN TEANA 2014 Service Manual

ENGINE CONTROL SYSTEMEC-527
< SYMPTOM DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
SYMPTOM DIAGNOSIS
ENGINE CONTROL SYSTEM
Symptom TableINFOID:0000000009462460
SYSTEM — BASIC ENGINE CONTROL SYSTEM
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA
Fuel Fuel pump circuit 11232 22 3 2 EC-508
Fuel pressure regulator system 334444444 4EC-182
Fuel injector circuit 11232 22 2EC-505
Fuel level sensor circuitEC-376,
EC-378
Fuel tank temperature sensor circuit EC-304,
EC-306
Evaporative emission system 334444444 4 EC-536
Air Positive crankcase ventilation sys-
tem 334444444 41
EC-539
Incorrect idle speed adjustment 1 1 1 1 1 EC-179
Electric throttle control actuator 112332222 2 2EC-475,
EC-480
IgnitionIncorrect ignition timing adjustment33111 11 1 EC-535
Ignition circuit 11222 22 2EC-511
Main power supply and ground circuit 22333 33 23 EC-203
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-528
< SYMPTOM DIAGNOSIS >[QR25DE]
ENGINE CONTROL SYSTEM
Mass air flow sensor circuit
1
12 2
222 2 EC-228,
EC-232
Intake air temperature sensor circuit EC-240,
EC-241
Engine coolant temperature sensor circuit
333
EC-245,
EC-251
Air fuel ratio (A/F) sensor 1 circuit EC-258
,
EC-262
,
EC-265
,
EC-289
,
EC-468
Throttle position sensor circuit
22EC-248
,
EC-315
,
EC-426
,
EC-427
,
EC-488
Accelerator pedal position sensor circuit 3 2 1 EC-482
,
EC-485
,
EC-491
Heated oxygen sensor 2 circuit 6 6 6 6 5 EC-268
,
EC-276
,
EC-284
Knock sensor circuit 2 3 EC-324
Engine oil temperature sensor circuit 4 2 3EC-311,
EC-312
Engine oil pressure sensor circuit 4 4 3 3 3 3 EC-388,
EC-392
Crankshaft position sensor (POS) circuit 2 2 EC-326
Camshaft position sensor (PHASE) circuit 3 2EC-329
Vehicle speed signal circuit 2 3 3 3EC-380
ECM 22333333333EC-400
,
EC-401
,
EC-402
,
EC-404
Intake valve timing control solenoid valve cir-
cuit 32 13223 3 EC-209,
EC-221
Intake valve timing intermediate lock control
solenoid valve circuit EC-394
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENGINE CONTROL SYSTEMEC-529
< SYMPTOM DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
1 - 6: The numbers refer to the order of inspection.
(continued on next table)
SYSTEM — ENGINE MECHANICAL & OTHER
Exhaust valve timing control solenoid valve
circuit 32 13223 3
EC-225
PNP signal circuit 3 3 3 3 3 EC-410
Refrigerant pressure sensor circuit 2 3 3 4EC-523
Electrical load signal circuit 3EC-503
Intake manifold runner control valve motor cir-
cuit 44
EC-462
Intake manifold runner control valve position
sensor circuit 44
EC-465
Intake manifold tuning valve circuit 1 EC-456
Manifold absolute pressure sensor circuit 3EC-236
Air conditioner circuit 223333333 3 2HAC-46,
HAC-139
Battery current sensor circuit 4 5 5 3 EC-428
,
EC-431
,
EC-434
,
EC-438
Battery temperature sensor circuit 4 5 5 3 EC-440
ASCD steering switch circuitEC-442
ABS actuator and electric unit (control unit) 4BRC-55
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-536
< PERIODIC MAINTENANCE >[QR25DE]
EVAPORATIVE EMISSION SYSTEM
EVAPORATIVE EMISSION SYSTEM
InspectionINFOID:0000000009462465
EVAP CANISTER
1.CHECK EVAP CANISTER
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
>> INSPECTION END
PBIB1212E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EVAP LEAK CHECKEC-537
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
EVAP LEAK CHECK
InspectionINFOID:0000000009462466
CAUTION:
• Do not use compressed air or a high pressure pump.
• Do not exceed 4.12 kPa (0.042 kg/cm
2, 0.6 psi) of pressure in EVAP system.
NOTE:
• Do not start engine.
• Improper installation of EVAP service port adapter [commercial service tool: (J-41413-OBD)] to the EVAP
service port may cause a leak.
1.EVAP LEAK CHECK
With CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
2. Turn ignition switch ON.
3. Select the “EVAP SYSTEM CLOSE” in “WOR K SUPPORT” mode of “ENGINE” using CONSULT.
4. Touch “START”. A bar graph (Pressure indicating display) will appear on the screen.
5. Apply positive pressure to the EVAP system until t he pressure indicator reaches the middle of the bar
graph.
6. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
7. Locate the leak using a leak detector [commercial service tool: (J-41416)]. Refer to EC-62, "EVAPORATIVE EMISSION SYS-
TEM : System Description".
Without CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
SEF200U
SEF462UA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-538
< PERIODIC MAINTENANCE >[QR25DE]
EVAP LEAK CHECK
2. Apply battery voltage between the terminals of EVAP
canister vent control valve to make a closed EVAP
system.
3. To locate the leak, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to
2.76 kPa (0.014 to 0.028 kg/cm
2, 0.2 to 0.4 psi).
4. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
5. Locate the leak using a leak detector [commercial service tool: (J-41416)]. Refer to EC-62, "EVAPORATIVE EMISSION SYS-
TEM : System Description".
>> INSPECTION END
SEF200U
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-546
< PREPARATION >[VQ35DE]
PREPARATION
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000009462478
The actual shape of the tools may differ from those illustrated here.
Commercial Service ToolsINFOID:0000000009462479
Tool number
(TechMate No.)
Tool name Description
(J-44321)
Fuel pressure gauge
kit Checks fuel pressure
(J-44321-6)
Fuel pressure adapter Connects fuel pressure gauge to quick connector
type fuel lines
LEC642
LBIA0376E
Tool name
(TechMate No.) Description
(J-45488)
Quick connector re-
lease Removes fuel tube quick connectors in engine
room
Leak detector
i.e.: (J-41416) Locates the EVAP leakage
EVAP service port
adapter
i.e.: (J-41413-OBD) Applys positive pressure through EVAP service
port
PBIC0198E
S-NT703
S-NT704
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PREPARATIONEC-547
< PREPARATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Fuel filler cap adapter
i.e.: (MLR-8382) Checks fuel tank vacuum relief valve opening
pressure
Socket wrench Removes and installs engine coolant temperature sensor. Refer to CO-51, "Exploded View"
.
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12) Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907) Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(TechMate No.) Description
S-NT815
S-NT705
AEM488
S-NT779
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-548
< SYSTEM DESCRIPTION >[VQ35DE]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM :
Component Parts LocationINFOID:0000000009462480
ENGINE ROOM
ALBIA0805ZZ
No. Component Function
1. Power valve actuator 1 EC-561, "Power Valve Actuator 1 and 2"
2. Electronic controlled engine mount control solenoid valveEC-556, "Electronic Controlled Engine Mount"
3. Cooling fan motor-2EC-554, "Cooling Fan"
4. Cooling fan motor-1EC-554, "Cooling Fan"
5. ECMEC-555, "ECM"
6. Refrigerant pressure sensorEC-562, "Refrigerant
Pressure Sensor"Refer to HAC-9, "Component Part Location" for detailed installa-
tionlocation.
7. Battery current sensor (with battery temperature sensor) EC-553, "Battery Current Sensor (With Battery Temperature Sen-
sor)"
8. Cooling fan motor relay-2
EC-554, "Cooling Fan"
9. Cooling fan motor relay-3EC-554, "Cooling Fan"
10. IPDM E/RIPDM E/R activates the internal control circuit to perform the relay
ON-OFF control according to the input signals from various sen-
sors and the request signals received from control units via CAN
communication.
Refer to PCS-4, "Component Parts Location"
for detailed installa-
tionlocation.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-549
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
ENGINE
11. Mass air flow sensor (with intake air temperature sensor)
EC-560, "Mass Air Flow Sensor (With Intake Air Temperature Sen-sor)"
12. Electric throttle control actuator
EC-555, "Electric Throttle Control Actuator"
13. Power valve actuator 2 EC-561, "Power Valve Actuator 1 and 2"
14. EVAP canister purge volume control solenoid valveEC-557, "EVAP Canister Purge Volume Control Solenoid Valve"
15. VIAS control solenoid valve 2EC-562, "VIAS Control Solenoid Valve 1 and 2"
16. VIAS control solenoid valve 1EC-562, "VIAS Control Solenoid Valve 1 and 2"
No. Component Function
A. Engine rear upper-left B. Engine top center C. Engine front lower-right
:Vehicle front
No. Component Function
1. Camshaft position sensor (PHASE)
(bank 1) EC-554, "Camshaft Position Sensor (PHASE)"
2.Ignition coil (with power transistor)
(bank 1) EC-560, "Ignition Coil
(With Power Transistor)"
3. PCV valve EC-563, "Positive Crankcase Ventilation (PCV)"
4. Intake valve timing control solenoid valve (bank 1)EC-560, "Intake Valve Timing Control Solenoid Valve"
5. Engine oil pressure sensorEC-557, "Engine Oil Pressure Sensor"
6. Intake valve timing control solenoid valve (bank 2)EC-560, "Intake Valve Timing Control Solenoid Valve"
7. Crankshaft position sensor (POS)EC-554, "Crankshaft Position Sensor (POS)"
JPBIA5982ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM