battery NISSAN TEANA 2014 Owner's Manual

BCS
BCM (BODY CONTROL MODULE)BCS-31
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
ECU DIAGNOSIS INFORMATION
BCM (BODY CONTROL MODULE)
Reference ValueINFOID:0000000009462016
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure repor ted by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
ACC BATTERY SAVER When battery saver is OFF. STOP
ACC RLY -REQ When BCM is not requesting accessory relay activation. Off
When BCM is requesting accessory relay activation. On
AIR COND SW A/C switch OFF Off
A/C switch ON On
AIR PRESS FL Front left tire air pressure value kPa, kg/cm
2, psi
AIR PRESS FR Front right tire air pressure value kPa, kg/cm
2, psi
AIR PRESS RL Rear left ti re air pressure value
kPa, kg/cm
2, psi
AIR PRESS RR Rear right ti re air pressure value
kPa, kg/cm
2, psi
AUTO CRNK TME Remote engine start timer duration. sec
AUTO CRNK TMR When the remote engine start timer is OFF. Off
When the remote engine start timer is ON. On
AUTO LIGHT SW Lighting switch OFF Off
Lighting switch AUTO On
BRAKE SW 1 When the brake pedal is released On
When the brake pedal is depressed Off
BRAKE SW2 Brake pedal released Off
Brake pedal depressed On
BUZZER Buzzer in combination meter OFF Off
Buzzer in combination meter ON On
CDL LOCK SW Door lock/unlock switch does not operate Off
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW Door lock/unlock switch does not operate Off
Press door lock/unlock switch to the UNLOCK side On
CONFRM ID ALL The key ID does not match any key ID registered to BCM. Yet
The key ID matches any key ID registered to BCM. DONE
CONFIRM ID4 The key ID does not match the fourth key ID registered to BCM. Yet
The key ID matches the fourth key ID registered to BCM. DONE
CONFIRM ID3 The key ID does not match the third key ID registered to BCM. Yet
The key ID matches the third key ID registered to BCM. DONE
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-37
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
1
(R) Ground Engine start switch Input Push-button igni-
tion switch Pressed 0V
Not pressed Battery voltage
3
(BR) Ground Auto light power sup-
ply 5V OutputPush-button igni-
tion switch OFF 0V
ACC or ON 5V
4
(Y) Ground Auto light signal Input
Push-button igni-
tion switch ON When outside of the vehi-
cle is bright Close to 5V
When outside of the vehi-
cle is dark Close to 0V
10
(W) Ground Combination switch
input 5 InputCombination
switch
(Wiper intermit-
tent dial 4) OFF 0V
TURN RH
1.0V
HEADLAMP 1
HI BEAM
TA I L L A M P
11
(BG) Ground Combination switch
input 4 InputCombination
switch
(Wiper intermit-
tent dial 4) OFF 0V
TURN LH
1.0V
PASSING
HEADLAMP 2
FR FOG
12
(W) Ground Combination switch
input 3 InputCombination
switch
(Wiper intermit-
tent dial 4) OFF 0V
FR WIPER LOW
1.0V
FR WIPER INT/AUTO
AUTO LIGHT
13
(G) Ground Combination switch
input 2 InputCombination
switch
(Wiper intermit-
tent dial 4) OFF 0V
FR WASHER
1.0V
INT VOLUME 3
PKIB4958J
PKIB4958J
PKIB4958J
PKIB4958J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-38
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
14
(P) Ground Combination switch
input 1 InputCombination
switch
(Wiper intermit-
tent dial 4) OFF 0V
FR WIPER HI
1.0V
INT VOLUME 1
INT VOLUME 2
17
(B) Ground Auto light reference
ground Input Push-button ignition switch ON 0V
18
(G) Ground Security indicator Output Security indicator ON 0V
Blinking 11 . 3 V
OFF Battery voltage
19
(G) Ground Lock switch signal Input
Door lock/unlock
switch Lock Battery voltage
Unlock 0V
20
(W) Ground Shift P Input Selector lever P position 0V
Any position other than P Battery voltage
21
(W) Ground Step lamp control Output Step lamp ON 0V
OFF Battery voltage
23
(L) Ground
Compressor ON sig-
nal Input A/C switch OFF 9.0 - 12.0V
ON 0V
24
(G) Ground Front door lock as-
sembly LH (key cylin-
der switch) Input
Key cylinder
switch OFF (neutral) 5V
ON (unlock) 0V
25
(BG) Ground Brake switch fuse Input — Battery voltage
26
(Y) Ground Shorting input Input Push-button ignition switch OFF Battery voltage
27
(G) Ground Brake switch lamp Input Stop lamp switch OFF (brake pedal is not de-
pressed) 0V
ON (brake pedal is de-
pressed) Battery voltage
29
(Y) Ground Front blower monitor Input
Front blower mo-
tor switch ON Battery voltage
OFF 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
PKIB4958J
JPMIA0014GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-39
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N30
(P) Ground Driver door lock sta-
tus Input Front door LH LOCK status
11 . 8 V
UNLOCK status 0V
32
(Y) Ground
Rear window defog-
ger ON signal Input
Rear window de-
fogger switch OFF 5V
ON 0V
33
(G) Ground Trunk lid opener can-
cel switch InputTrunk lid opener
cancel switch CANCEL
1.1V
ON 0V
34
(BG) Ground Unlock switch signal Input Door lock/unlock
switch Unlock Battery voltage
Lock 0V
36
(Y) Ground Hazard switch Input Hazard switch Pressed 0V
Not pressed
1.1V
39
(L) Ground Shift N/P Input Selector lever P or N position Battery voltage
Except P and N positions 0V
48
(BR) Ground
High side start switch
LED OutputPush-button igni-
tion switch illumi-
nation ON 5.5V
OFF 0V
52
(G) Ground Audio dongle
Input/
Output Push-button ignition switch OFF 5V
54
(P) Ground
Power window link/
communication Input/
Output Push-button igni-
tion switch ON
10.2V
OFF or ACC 0V
59
(P) Ground CAN low
Input/
Output ——
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JPMIA0011GB
JPMIA0012GB
JPMIA0012GB
JPMIA0013GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-40
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
60
(L) Ground CAN high Input/
Output ——
61
(Y) Ground Rear defogger relay
output OutputRear window de-
fogger Active Battery voltage
Not activated 0V
62
(BR) Ground Starter relay output Output
Push-button igni-
tion switch ON When selector lever is in P
or N position and the brake
is depressed Battery voltage
When selector lever is in P
or N position and the brake
is not depressed 0V
64
(W) Ground Buzzer output Output Outside warning
buzzer Sounding 0V
Not sounding Battery voltage
66
(R) Ground Blower fan relay out-
put OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
67
(W) Ground Ignition electrical re-
lay output 2 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
68
(P) Ground Dimmer signal output Output
Push-button igni-
tion switch ON Either of the following con-
ditions
• Lighting switch OFF
• The area around the ve- hicle is bright (Shine a
light on the optical sen-
sor) 0V
The area around the vehi-
cle is dark (Block the light
from the optical sensor) Battery voltage
69
(L) Ground CVT device output Output — Battery voltage
70
(G) Ground IPDM E/R ignition
output 1 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
71
(V) Ground Driver request switch Input
Front door LH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
72
(Y) Ground Passenger request
switch InputFront door RH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JPMIA0016GB
JPMIA0016GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-43
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
80
(BR) Ground Trunk open switch Output trunk Open (trunk actuator is ac-
tivated) Battery voltage
Close (trunk actuator is not
activated) 0V
82
(Y) Ground Left rear door switch Input Rear door LH
switch OFF (when rear door LH
closes)
11 . 8 V
ON (when rear door LH
opens) 0V
85
(BG) Ground Trunk room lamp Output Trunk room lamp ON 0V
OFF Battery voltage
91
(V) Ground Trunk lid opening Output Trunk lid Open (trunk lid opener ac-
tuator is activated) Battery voltage
Close (trunk lid opener ac-
tuator is not activated) 0V
92
(LG) Ground Right rear flasher Output
Push-button igni-
tion switch ON Turn signal switch OFF 0V
Turn signal switch RH 6.5 V
93
(V) Ground Right rear door
switch InputRear door RH
switch OFF (when rear door RH
closes)
11 . 8 V
ON (when rear door RH
opens) 0V
94
(SB) Ground Passenger door
switch InputFront door RH
switch OFF (when front door RH
closes)
11 . 8 V
ON (when front door RH
opens) 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JPMIA0011GB
PKID0926E
JPMIA0011GB
JPMIA0011GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-46
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
105
(BR) Ground Right front flasher Output Push-button igni-
tion switch ON Turn signal switch OFF 0V
Turn signal switch RH
6.5 V
107 (W) Ground Low side start switch
LED InputPush-button igni-
tion switch OFF 0V
NOTE:
When the illumination
brightening/dimming level
is in the neutral position
ON
108
(BG) Ground Shift lock solenoid
output Input Selector lever P position 0V
Any position other than P Battery voltage
109 (G) Ground Reverse signal Output Push-button igni-
tion switch ON R position Battery voltage
Any position other than R 0V
111 (Y) Ground ACC LED Output Push-button igni-
tion switch OFF Battery voltage
ACC or ON 0V
11 3 (P) Ground ACC relay output Output Push-button igni-
tion switch OFF 0V
ACC or ON Battery voltage
11 4 (P) Ground Outside key antenna
RH A OutputWhen the front
door RH request
switch is operat-
ed with push-but-
ton ignition switch
OFF When Intelligent Key is in
the antenna detection area
When Intelligent Key is not
in the antenna detection
area
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
PKID0926E
JSNIA0010GB
JMKIA0062GB
JMKIA0063GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-49
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
126
(BR) Ground
NATS antenna amp.
B Input/
Output During waiting Intelligent Key backside is
contacted to push-button
ignition switch, turn ignition
switch ON. Just after pressing push-button
ignition switch. Pointer of analog
volt meter should move.
127 (L) Ground
NATS antenna amp.
A Input/
Output During waiting Intelligent Key backside is
contacted to push-button
ignition switch, turn ignition
switch ON. Just after pressing push-button
ignition switch. Pointer of analog
volt meter should move.
128
(BG) Ground
Front console anten-
na B Output
Push-button igni-
tion switch OFF When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
129 (G) Ground Battery saver output Output After passing the interior room lamp battery sav-
er operation time 0V
Any other time after passing the interior room
lamp battery saver operation time Battery voltage
130
(SB) Ground Passenger door un-
lock Output Front door RH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
131 (W) Ground BCM battery fuse Input Push-button ignition switch OFF Battery voltage
132 (L) Ground Rear door lock Output All doors LOCK (actuator is activat-
ed) Battery voltage
Other than LOCK (actuator
is not activated) 0V
133 (Y) Ground Rear door unlock Output Rear door RH
and rear door LH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
134 (B) Ground Ground 2 — Push-button ignition switch ON 0V
135
(BR) Ground Driver, passenger
and fuel door lock Output All doors LOCK (actuator is activat-
ed) Battery voltage
Other than LOCK (actuator
is not activated) 0V
136 (P) Ground Room lamp control Output Interior room
lamp OFF Battery voltage
ON 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JMKIA0062GB
JMKIA0063GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-50
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
Fail Safe
INFOID:0000000009462017
DTC Inspection Priority ChartINFOID:0000000009462018
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the following priority
chart.
137
(V) Ground Driver and fuel door
unlock Output Front door LH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
138 (V) Ground Rear door battery Input Push-button ignition switch OFF Battery voltage
139 (W) Ground Fusible link battery
power Input Push-button ignition switch OFF Battery voltage
140
(LG) Ground
Power window igni-
tion power supply Output Push-button ignition switch ON Battery voltage
141 (V) Ground Power window bat-
tery power supply Output Push-button ignition switch OFF Battery voltage
142
(BR) Ground Front door battery Input Push-button ignition switch OFF Battery voltage
143 (B) Ground Ground 1 — Push-button ignition switch ON 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
Display contents of CONS ULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI-SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2560: STARTER CONT RELAY Inhibit engine cranking 500 ms after the following CAN signal communication status has
become consistent
• Starter control relay signal
• Starter relay status signal
B2562: LO VOLTAGE Inhibit engine cranking 100 ms after the power supply voltage increases to more than 8.8 V
B2608: STARTER RELAY Inhibit engine cranking 500 ms after the following signal communication status becomes
consistent
• Starter motor re lay control signal
• Starter relay status signal (CAN)
B260A: IGNITION RELAY Inhibit engine cranking 500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B2617: STARTER RELAY CIRC Inhibit engine cranking 1 second after the starter motor
relay control inside BCM becomes
normal
B2618: BCM Inhibit engine cranking 1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
B2562 LOW VOLTAGEBCS-71
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2562 LOW VOLTAGE
DTC LogicINFOID:0000000009462036
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the Self Diagnostic Result of BCM with CO NSULT, after the ignition switch has been turned ON
for 120 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-71, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462037
1. CHECK BATTERY VOLTAGE
Check battery voltage.
Is battery voltage less than 8.8V?
YES >> Charge battery and retest. Refer to CHG-17, "Work Flow (With EXP-800 NI or GR8-1200 NI)" or
CHG-20, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
.
NO >> GO TO 2.
2. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to BCS-74, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. BCM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of BCM with CONSULT. Refer to BCS-25, "BCM : CONSULT Function (BCM -
BCM)".
Is DTC B2562 CRNT?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detection Condition Possible cause
LOW VOLTAGE
[B2562] When the power supply voltage to BCM remains less
than 8.8V for 120 seconds or more • Harness or connector (power supply circuit)
• Vehicle battery
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM