heater NISSAN TEANA 2014 Owner's Manual

ECM
EC-89
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
CLSD THL POS
• Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released On
Accelerator pedal: Slightly depressed Off
AIR COND SIG • Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates.) On
PW/ST SIGNAL • Engine: After warming up, idle the
engine Steering wheel: Not being turned Off
Steering wheel: Being turned On
LOAD SIGNAL • Ignition switch: ON Rear window defogger switch: ON
and/or Lighting switch: 2nd position On
Rear window defogger switch and lighting
switch: OFF Off
IGNITION SW • Ignition switch: ON → OFF → ON On → Off → On
HEATER FAN SW • Engine: After warming up, idle the
engine Heater fan switch: ON On
Heater fan switch: OFF Off
BRAKE SW • Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
INJ PULSE-B1 • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle 2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
IGN TIMING • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle 5
° - 15 ° BTDC
2,000 rpm 25 ° - 45 ° BTDC
CAL/LD VALUE • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle 10% - 35%
2,500 rpm 10% - 35%
MASS AIRFLOW • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle 1.0 - 4.0 g/s
2,500 rpm 4.0 - 10.0 g/s
PURG VOL C/V • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.) 0%
2,000 rpm 20% - 90%
INT/V TIM(B1) • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle
−5 ° - 5 °CA
4,000 rpm Approx. 0 ° - 30 °CA
EXH/V TIM B1 • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle
−5 ° - 5 °CA
2,000 rpm Approx. 0 ° - 40 °CA
INT/V SOL (B1) • Engine: Idle speed
• Selector lever: P or N
• Air conditioner switch: OFF
•No load After warming up 0%
Cold condition [Engine coolant tempera-
ture below 60 °C (140 °F)] Approx. 50% - 100%
SWRL CONT S/V • Ignition switch: ON
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F) Accelerator pedal: Fully released On
Accelerator pedal: Fully depressed Off
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O50
(L) 128
(GR) Intake manifold runner
control valve motor power
supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
51
(B) 128
(GR) Intake manifold runner
control valve motor
(Open) Output[Ignition switch ON]
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F)
• Accelerator pedal: Fully released →
depressed Battery voltage appears for about
1 second.
52
(B) — ECM ground — — —
53
(BR) 128
(GR) A/F sensor 1 heater Input [Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after start-
ing engine) 2.9 - 8.8 V
54
(Y) 128
(GR) Heated oxygen sensor 2
heater Output[Engine is running]
• Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm Battery voltage
(11 - 14 V)
56
(SB) 128
(GR) Intake valve timing inter-
mediate lock control sole-
noid valve Output[Engine is running]
• Warm-up condition
• Idle speed 0 V
[Engine is running]
• Cold condition [Engine coolant tem- perature: below 60 °C (140 °F)]
• Idle speed Battery voltage
(11 - 14 V)
58
*1
(L) —Sensor ground
[Manifold absolute pres-
sure (MAP) sensor] —— —
59
*1
(LG) 58
*1
(L)Manifold absolute pres-
sure (MAP) sensor Output[Engine is running]
• Warm-up condition
• Both A/C switch and blower fan switch: ON (Compressor operates) 4.6 V
Output voltage atmospheric pressure.
[Engine is running]
• Warm-up condition
• Idle speed 1.2 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 1.5 V
60
*1
(V) —Sensor power supply
[Manifold absolute pres-
sure (MAP) sensor] — [Ignition switch: ON] 5.0 V
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JPBIA4732ZZ
JMBIA0325GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-105
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
DTC IndexINFOID:0000000009462124
×
:Applicable —: Not applicable
2 P0031, P0032 Air fuel ratio (A/F) sensor 1 heater
P0037, P0038 Heated oxygen sensor 2 heater
P0075 Intake valve timing control solenoid valve/Intake valve timing
intermediate lock control solenoid valve
P0078 Exhaust valve timing control solenoid valve
P0130, P0131, P0132, P014 C, P014D, P015A, P015B,
P117A, P2096, P2097 Air fuel ratio (A/F) sensor 1
P0137, P0138, P0139 Heated oxygen sensor 2
P0441 EVAP control system purge flow monitoring
P0443, P0444, P0445 EVAP canister purge volume control solenoid valve
P0447, P0448 EVAP canister vent control valve
P0451, P0452, P0453 EVAP control system pressure sensor
P1217 Engine over temperature (OVERHEAT)
P1800 Intake manifold tuning valve
P1805 Brake switch
P2004 Intake manifold runner control valve
P2100, P2103 Throttle control motor relay
P2101 Electric thrott le control function
P2118 Throttle control motor
3 P0011, P052A, P052B Intake valve timing control
P0014 Exhaust valve timing control
P0171, P0172 Fuel injection system function
P0300, P0301, P0302, P0303, P0304 Misfire
P0420 Three way catalyst function
P0456 EVAP control system
P0506, P0507 Idle speed control system
P050A, P050B, P050E Cold start control
P0524 Engine oil pressure
P1148 Closed loop control
P1212 TCS communication line
P1564 ASCD steering switch
P1572 ASCD brake switch
P1574 ASCD vehicle speed sensor
P1715 Input speed sensor
P2119 Electric throttle control actuator
Priority DTC Detected items
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Reference page
CONSULT
GST
*2ECM*3
U0101 0101*5CAN COMM CIRCUIT — 1 ×BEC-207
U1001
1001*5CAN COMM CIRCUIT — 2 — — EC-208
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-114
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
O2 SEN-
SOR
HEATER 41H A/F sensor 1 heater (Bank 1)
Low Input: P0031
High Input: P0032 81H 0BHConverted value of heater electric cur-
rent to voltage
42H Heated oxygen sensor 2 heat-
er (Bank 1) Low Input: P0037
High Input: P0038 80H 0CH
Converted value of heater electric cur-
rent to voltage
43H Heated oxygen sensor 3 heat-
er (Bank 1) P0043 80H 0CHConverted value of heater electric cur-
rent to voltage
45H A/F sensor 1 heater (Bank 2) Low Input: P0051
High Input: P0052 81H 0BHConverted value of heater electric cur-
rent to voltage
46H Heated oxygen sensor 2 heat-
er (Bank 2) Low Input: P0057
High Input: P0058 80H 0CH
Converted value of heater electric cur-
rent to voltage
47H Heated oxygen sensor 3 heat-
er (Bank 2) P0063 80H 0CHConverted value of heater electric cur-
rent to voltage
SEC-
OND-
ARY AIR 71H Secondary air system P0411 80H 01H
Secondary air injection system incor-
rect flow detected
Bank1: P0491
Bank2: P0492 81H 01H
Secondary air injection system insuffi-
cient flow
P2445 82H 01H Secondary air injection system pump
stuck off
P2448 83H 01H Secondary air injection system high
airflow
Bank1: P2440
Bank2: P2442 84H 01H
Secondary air injection system switch-
ing valve stuck open
P2440 85H 01H Secondary air injection system switch-
ing valve stuck open
P2444 86H 01H Secondary air injection system pump
stuck on
FUEL
SYSTEM 81H
Fuel injection system function
(Bank 1) P0171 or P0172 80H 2FH Long term fuel trim
P0171 or P0172 81H 24H The number of lambda control
clamped
P117A 82H 03H Cylinder A/F imbalance monitoring
82H Fuel injection system function
(Bank 2) P0174 or P0175 80H 2FH Long term fuel trim
P0174 or P0175 81H 24H The number of lambda control
clamped
P117B 82H 03H Cylinder A/F imbalance monitoring
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

P0031, P0032 A/F SENSOR 1 HEATER
EC-215
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
P0031, P0032 A/F SENSOR 1 HEATER
DTC LogicINFOID:0000000009462165
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than between 11 V at
idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-215, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009462166
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2. Turn ignition switch ON.
3. Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
DTC No. Trouble diagnosis name
(Trouble diagnosis con-
tent) DTC detecting condition Possible cause
P0031 A/F SEN1 HTR (B1)
(HO2S heater control cir-
cuit low bank 1 sensor 1) The current amperage in the A/F sensor 1 heater
circuit is out of the normal range.
(An excessively low voltage signal is sent to ECM
through the A/F sensor 1 heater.) • Harness or connectors
(A/F sensor 1 heater circuit is open or
shorted.)
• A/F sensor 1 heater
P0032 A/F SEN1 HTR (B1)
(HO2S heater control cir-
cuit high bank 1 sensor 1) The current amperage in the A/F sensor 1 heater
circuit is out of the normal range.
(An excessively high voltage signal is sent to ECM
through the A/F sensor 1 heater.) • Harness or connectors
(A/F sensor 1 heater circuit is short-
ed.)
• A/F sensor 1 heater
+
−Vo l ta g e
A/F sensor 1
Connector Terminal F24 4 Ground Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-216
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
P0031, P0032 A/F SENSOR 1 HEATER
3. Check the continuity between A/F sensor
1 harness connector and ECM harness connector.
*1: Except for California
*2: For California
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
3.CHECK A/F SENSOR 1 HEATER
Check the A/F sensor 1 heater. Refer to EC-216, "Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 4.
4.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to EM-33, "Exploded View"
.
CAUTION:
• Discard any A/F sensor which has b een dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhau st system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize Lubricant
(commercial service tool).
>> INSPECTION END
Component InspectionINFOID:0000000009462167
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect A/F sensor 1 harness connector.
3. Check resistance between A/F sensor 1 terminals as per the following.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-33, "Exploded View"
.
CAUTION:
+ −
Continuity
A/F sensor 1 ECM
Connector Terminal Connector Terminal
F24 3 F13
*1
F90*253 Existed
A/F sensor 1
Resistance
+ −
Te r m i n a l
3 4 1.8 - 2.44
Ω [at 20 °C (68 °F)]
1
∞ Ω
(Continuity should not exist)
2
4 1
2
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

P0031, P0032 A/F SENSOR 1 HEATER
EC-217
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
• Discard any sensor which has been dropped from a he
ight of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust syst em threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-218
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
P0037, P0038 HO2S2 HEATER
P0037, P0038 HO2S2 HEATER
DTC LogicINFOID:0000000009462168
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5. Let engine idle for 1 minute.
6. Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES >> Proceed to EC-218, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009462169
1.CHECK HO2S2 POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
3. Turn ignition switch ON.
4. Check the voltage between HO2S2 harness connector and ground.
DTC No. Trouble diagnosis name
(Trouble diagnosis con-
tent) DTC detecting condition Possible cause
P0037 HO2 HTR (B1)
(HO2S heater control cir-
cuit low bank 1 sensor 2) The current amperage in the heated oxygen sensor
2 heater circuit is out of the normal range.
(An excessively low voltage signal is sent to ECM
through the heated oxygen sensor 2 heater.) • Harness or connectors
(Heated oxygen sensor 2 heater cir-
cuit is open or shorted.)
• Heated oxygen sensor 2 heater
P0038 HO2 HTR (B1)
(HO2S heater control cir-
cuit high bank 1 sensor 2) The current amperage in the heated oxygen sensor
2 heater circuit is out of the normal range.
(An excessively high voltage signal is sent to ECM
through the heated oxygen sensor 2 heater.) • Harness or connectors
(Heated oxygen sensor 2 heater cir-
cuit is shorted.)
• Heated oxygen sensor 2 heater
+
−Voltag e
HO2S2
Connector Terminal F42 2 Ground Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

P0037, P0038 HO2S2 HEATEREC-219
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK HO2S2 OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between HO2S2 harness connector and ECM harness connector.
*1: Except for California
*2: For California
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK HEATED OXYGEN SENSOR 2 HEATER
Check the heated oxygen sensor 2 heater. Refer to EC-219, "Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 4.
4.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View"
.
CAUTION:
• Discard any sensor which has been dropped from a he ight of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust syst em threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Component InspectionINFOID:0000000009462170
1.CHECK HEATED OXYGEN SENSOR 2 HEATER
1. Turn ignition switch OFF.
2. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
3. Check resistance between HO2S2 terminals as per the following.
+ −
Continuity
HO2S2 ECM
Connector Terminal Connector Terminal
F42 3 F13
*1
F90*254 Existed
Heated oxygen sensor 2
Resistance
+ −
Te r m i n a l
2 3 3.3 - 4.4 Ω [at 25 °C (77 °F)]
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-220
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
P0037, P0038 HO2S2 HEATER
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View"
.
CAUTION:
• Discard any sensor which has been dropped from a he ight of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
• Before installing new sensor, clean exhaust system threads usi ng Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
1 1
∞ Ω
(Continuity should not exist)
3
4
4 1
2
3
Heated oxygen sensor 2
Resistance
+ −
Te r m i n a l
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM