NISSAN TEANA 2014 Service Manual

PCS-12
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
ECU DIAGNOSIS INFORMATION
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference ValueINFOID:0000000009461603
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
RAD FAN REQ Engine idle speed Changes depending on engine cool-
ant temperature, air conditioner op-
eration status, vehicle speed, etc. 1, 2, 3, 4
AC COMP REQ Engine running A/C switch OFF Off
A/C switch ON
(Compressor is operating) On
TAIL&CLR REQ Lighting switch OFF Off
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated) On
HL LO REQ Lighting switch OFF Off
Lighting switch 2ND HI or AUTO (Light is illuminated) On
HL HI REQ Lighting switch OFF Off
Lighting switch HI On
FR FOG REQ Lighting switch 2ND or
AUTO (Light is illuminated) Front fog lamp switch OFF Off
• Front fog lamp switch ON
• Daytime running light activated (Only for Canada models) On
FR WIP REQ Ignition switch ON Front wiper switch OFF STOP
Front wiper switch INT 1LOW
Front wiper switch LO Low
Front wiper switch HI Hi
WIP AUTO STOP Ignition switch ON Front wiper stop position STOP P
Any position other than front wiper
stop position ACT P
WIP PROT Ignition switch ON Front wiper operates normally Off
Front wiper stops at fail-safe opera-
tion BLOCK
IGN RLY1 -REQ Ignition switch OFF or ACC Off
Ignition switch ON On
IGN RLY Ignition switch OFF or ACC Off
Ignition switch ON On
PUSH SW Release the push-button ignition switch Off
Press the push-button ignition switch On
INTER/NP SW Ignition switch ON CVT selector lever in any position
other than P or N Off
CVT selector lever in P or N position On
ST RLY CONT Ignition switch ON Off
At engine cranking On
IHBT RLY -REQ Ignition switch ON Off
At engine cranking On
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-13
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D E
F
G H
I
J
K L
B
A
O P
N
ST/INHI RLY
Ignition switch ON Off
At engine cranking ST →INHI
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the
starter control relay is OFF UNKWN
DETENT SW Ignition switch ON • Press the selector button with
CVT selector lever in P position
• CVT selector lever in any position
other than P Off
Release the CVT selector button with CVT selector lever in P position On
DTRL REQ DTRL OFF Off
DTRL ON On
HOOD SW Hood closed Off
Hood open On
THFT HRN REQ Not operated Off
• Panic alarm is activated
• Horn is activated with VEHICLE SECURITY (THEFT WARNING) SYS- TEM On
HORN CHIRP Not operated Off
Door locking with Intelligent Key (horn chirp mode) On
HOOD SW 2 Hood closed Off
Hood open On
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS-14
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
TERMINAL LAYOUT
PHYSICAL VALUES
AWMIA1307ZZ
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
1
(R) Ground Fusible link main Input Ignition switch OFF Battery voltage
2
(L) Ground Fusible link IPDM E/R Input Ignition switch OFF Battery voltage
3
(G) Ground Fusible link ignition switch Input Ignition switch ON Battery voltage
4
(P) Ground Motor fan 1 Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
6
(R) Ground Fusible link motor fan Input Ignition switch OFF 0V
Ignition switch ON Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-15
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D E
F
G H
I
J
K L
B
A
O P
N
7
(B) Ground Ground (Power) — Ignition switch ON 0V
9
(SB) Ground Tail RH Output Ignition
switch ON Lighting switch OFF 0V
Lighting switch 1ST Battery voltage
10
(V) Ground Tail LH Output Ignition
switch ON Lighting switch OFF 0V
Lighting switch 1ST Battery voltage
11
(Y) Ground Front wiper LO Output Ignition
switch ON Front wiper switch OFF 0V
Front wiper switch LO Battery voltage
13
(LG) Ground ECM battery Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
14
(Y) Ground Daytime running lamps Output Ignition switch OFF Battery voltage
15
(R) Ground Fuel pump Output Approximately 1 second or more after
turning the ignition switch ON 0V
• Approximately 1 second after turning the ignition switch ON
• Engine running Battery voltage
18
(L) Ground Front wiper HI Output Ignition
switch ON Front wiper switch OFF 0V
Front wiper switch HI Battery voltage
19
(BR) Ground Power steering control unit Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
21
(L) Ground ECM ignition switch Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
22
(W) Ground Horn relay Input The horn is deactivated Battery voltage
The horn is activated 0V
23
(V) Ground Horn switch Input The horn is deactivated Battery voltage
The horn is activated 0V
27
(BG) Ground Fan motor relay mid Input Ignition switch OFF 0V
Ignition switch ON 0.7V
28
(P) —CAN-L
Input/
Output ——
29
(L) —CAN-H Input/
Output ——
31
(Y) Ground Detent switch Input Ignition
switch ON Press the CVT selector
button (CVT selector lever
P) Battery voltage
• CVT selector lever in any position other than
P
• Release the CVT selec- tor button (CVT selector
lever P) 0V
33
(R) Ground Starter control Input
Ignition
switch ON CVT selector lever in any
position other than P or N 0V
CVT selector lever P or N Battery voltage
34
(SB) Ground Wiper autostop Input Ignition
switch ON Front wiper stop position 0V
Any position other than
front wiper stop position Battery voltage
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS-16
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
35
(BR) Ground
ABS actuator and electric
unit (control unit) OutputIgnition switch OFF 0V
Ignition switch ON Battery voltage
36
(W) Ground Cooling fan relay-2, 3 Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
37
(W) Ground Transmission range switch
signal InputIgnition
switch ON CVT selector lever in P
(park) or N (neutral) posi-
tion Battery voltage
CVT selector lever in any
position other than P
(park) or N (neutral) posi-
tion 0V
38
(G) Ground Push start switch Input Press the push-button ignition switch 0V
Release the push-button ignition switch Battery voltage
39
(G) Ground Motor fan relay HI Input Ignition switch OFF 0V
Ignition switch ON 0.7V
41
(B) Ground Ground (signal) — Ignition switch ON 0V
43
(LG) Ground
Ignition signal
1InputIgnition switch OFF or ACC 0V
Ignition switch ON Battery voltage
45
2
(V) Ground Power distribution sensor
signal-E/R —• Ignition switch ON (READY)
• Both A/C switch and blower motor
switch ON (A/C compressor oper-
ates) 1.0 - 4.0V
45
3
(P)
47
2
(O) Ground Power distribution sensor
power-E/R — Ignition switch ON 5V
47
3
(BG)
48
(SB) Ground
Power distribution sensor
ground-E/R — Ignition switch ON 0V
49
(P) Ground Ambient sensor signal-E/R — Ignition switch ON 5V
50
(BG) Ground Ambient sensor ground-E/
R — Ignition switch ON 0V
51
(R) Ground Starter motor Output At engine cranking Battery voltage
52
2
(G) Ground O2 sensor #2 Output Ignition switch OFF 0V
52
3
(P) Ignition switch ON Battery voltage
53
2
(W) Ground O2 sensor #1 Output Ignition switch OFF 0V
53
3
(G) Ignition switch ON Battery voltage
54
(LG) Ground Injector #1 Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-17
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D E
F
G H
I
J
K L
B
A
O P
N
552
(W)
Ground Ignition coil Output Ignition switch OFF
(For a few seconds after turning ignition
switch OFF) 0V
55
3
(G) • Ignition switch ON
• Ignition switch OFF
(More than a few seconds after turn-
ing ignition switch OFF) Battery voltage
56
(SB) Ground A/C compressor Output
Engine
running A/C compressor OFF 0V
A/C compressor ON
(A/C compressor is oper-
ating) Battery voltage
57
(R) Ground Electronic throttle control Output Ignition switch OFF
(For a few seconds after turning ignition
switch OFF) 0V
• Ignition switch ON
• Ignition switch OFF (More than a few seconds after turn-
ing ignition switch OFF) Battery voltage
58
(SB) Ground ECM battery Output Ignition switch OFF Battery voltage
59
(L) Ground Engine solenoid Output Ignition switch OFF
(For a few seconds after turning ignition
switch OFF) 0V
• Ignition switch ON
• Ignition switch OFF (More than a few seconds after turn-
ing ignition switch OFF) Battery voltage
60
(Y) Ground Injector #2 Output Ignition switch OFF 0V
Ignition switch ON Battery voltage
61
(Y) Ground
Transmission control mod-
ule OutputIgnition switch OFF 0V
Ignition switch ON Battery voltage
65
2
(BR) Ground Throttle control motor re-
lay OutputIgnition switch ON
→ OFF 0 -1.0V
↓
Battery voltage ↓
0V
65
3
(L) Ignition switch ON 0 - 1.0V
66
(LG) Ground N/P switch Input Ignition
switch ON CVT selector lever in P or
N position Battery voltage
CVT selector lever in any
position other than P or N
position 0V
69
(V) Ground Fuel pump relay Output • Approximately 1 second after turning
the ignition switch ON
• Engine running 0 - 1.0V
Approximately 1 second or more after
turning the ignition switch ON Battery voltage
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS-18
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
71
(SB) Ground Alternator C Output Ignition switch ON
6.3V
40% is set on “Active test”, “ALTERNA-
TOR DUTY” of “ENGINE”
3.8V
80% is set on “Active test”, “ALTERNA-
TOR DUTY” of “ENGINE”
1.4V
72
2
(V) Ground ECM relay
(Self shut-off) OutputIgnition switch OFF
(For a few seconds after turning ignition
switch OFF) Battery voltage
72
3
(Y) • Ignition switch ON
• Ignition switch OFF (More than a few seconds after turn-
ing ignition switch OFF) 0 - 1.5V
74
4
(BG) Ground Washer motor Output Ignition switch ON Battery voltage
74
5
(V)
75
(R) Ground Headlamp LO RH Output Ignition
switch ON Lighting switch OFF 0V
Lighting switch 2ND Battery voltage
76
(P) Ground Headlamp LO LH Output Ignition
switch ON Lighting switch OFF 0V
Lighting switch 2ND Battery voltage
78
(W) Ground Front fog lamp RH Output Ignition
switch ON Fog lamp switch OFF 0V
Fog lamp switch ON Battery voltage
79
(G) Ground Front fog lamp LH Output Ignition
switch ON Fog lamp switch OFF 0V
Fog lamp switch ON Battery voltage
80
(L) Ground Headlamp HI RH Output
Ignition
switch ON • Lighting switch HI
• Lighting switch PASS Battery voltage
Lighting switch OFF 0V
81
(Y) Ground Headlamp HI LH Output Ignition
switch ON • Lighting switch HI
• Lighting switch PASS Battery voltage
Lighting switch OFF 0V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
JPMIA0001GB
JPMIA0002GB
JPMIA0003GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-19
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D E
F
G H
I
J
K L
B
A
O P
N
1: Ignition battery saver logic turns OFF the IPDM E/R and BCM if the ignition is ON for 30 minutes with the engine OFF.
2: With QR25DE.
3: With VQ35DE.
4: With rear view camera.
5: Without rear view camera.
Fail SafeINFOID:0000000009461604
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible,
IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
82
(W) Ground
Power distribution sensor
signal-fem —• Ignition switch ON (READY)
• Both A/C switch and blower motor switch ON (electric compressor oper-
ates) 1.0 - 4.0V
83
(G) Ground Power distribution sensor
power-fem — Ignition switch ON 5V
85
(V) Ground Daytime running lamps re-
lay OutputIgnition
switch ON Daytime light system ac-
tive Battery voltage
Ignition
switch ON Daytime light system inac-
tive 0V
86
(R) Ground Power distribution sensor
ground-fem — Ignition switch ON 0V
87
(P) Ground Ambient sensor signal-fem — Ignition switch ON 5V
90
(LG) Ground Clearance lamps Output Ignition
switch ON Lighting switch 1ST Battery voltage
Lighting switch OFF 0V
94
(SB) Ground Hood switch 2 Input Ignition
switch ON Hood closed 0V
Hood open Battery voltage
95
(BG) Ground Ambient sensor ground-
fem — Ignition switch ON 0V
96
(Y) Ground Hood switch Input
Ignition
switch ON Hood closed 0V
Hood open Battery voltage
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
Signal name Input/
Output
+ −
Control part Fail-safe in operation
Headlamp • Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
•Parking lamps
• Side marker lamps
• License plate lamps
• Tail lamps • Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper • The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail- safe control is activated while the front wipe r is set in the INT mode and the front wiper
motor is operating.
Horn Horn OFF
Ignition relay The status just before activation of fail-safe is maintained.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS-20
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seiz ure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
NOTE:
The tail lamp turns OFF when the ignition switch is turned ON.
FRONT WIPER CONTROL
IPDM E/R detects front wiper stop posit ion by a front wiper auto stop signal.
When a front wiper auto stop signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 second activation and 20 second stop five times.
NOTE:
This operation status can be confirmed on the IPDM E/ R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC IndexINFOID:0000000009461605
NOTE:
The details of TIME display are as follows.
• CRNT: The malfunctions that are detected now
• 1 - 39: The number is indicated when it is normal at present and a malfunction was detected in the past. It
increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF → ON. It is
fixed to 39 until the self-diagnosis results are erased if it is over 39. It returns to 0 when a malfunction is
detected again in the process.
DTC Ignition switch Ignition relay Tail lamp relay
—ONON—
—OFFOFF—
B2098: IGN RELAY ON OFF ON ON (10 minutes)
B2099: IGN RELAY OFF ON OFF —
Ignition switch Front wiper switch Auto stop signal
ON OFF
Front wiper stop position signal cannot be
input 10 seconds.
ON The signal does not change for 10 seconds.
CONSULT display Fail-safe TIMENOTERefer to
No DTC is detected. Further testing may be required. — — — —
U1000: CAN COMM CIRCUIT ×CRNT 1 – 39 PCS-27
U1010: CONTROL UNIT (CAN) ×CRNT 1 – 39 PCS-28
B2098: IGN RELAY ON ×CRNT 1 – 39 PCS-29
B2099: IGN RELAY OFF — CRNT 1 – 39 PCS-30
B210B: INHIBIT relay ON stuck failure — CRNT 1 – 39 SEC-73
B210C: INHIBIT relay OFF stuck failure — CRNT 1 – 39 SEC-74
B210D: STARTER relay ON stuck failure — CRNT 1 – 39 SEC-76
B210E: STARTER relay OFF stuck failure — CRNT 1 – 39SEC-78
B210F: Interlock/NP switch ON stuck failure — CRNT 1 – 39 SEC-80
B2110: Interlock/NP switch OFF stuck failure — CRNT 1 – 39 SEC-82
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-21
< WIRING DIAGRAM > [IPDM E/R]
C
D E
F
G H
I
J
K L
B
A
O P
N
WIRING DIAGRAM
IPDM E/R (INTELLIGENT POWER
DISTRIBUTION MODULE ENGINE
ROOM)
Wiring DiagramINFOID:0000000009461606
ABMWA2159GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM