height NISSAN TEANA 2014 Owner's Guide

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-35
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
4. Install the exhaust manifold cover (lower front) and bolts. Then
tighten the bolts to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
5. Install the air fuel ratio (A/F) sensor 1 (1) using Tools (A) and tighten to specification.
CAUTION:
• Be careful not to damage air fuel ratio (A/F) sensor.
• Discard any air fuel ratio (A/F) sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; replace with a new
one.
• Do not over-tighten the air fuel ratio (A/F) sensor 1. Doing so may cause damage to the air fuel
ratio (A/F) sensor 1, r esulting in a malfunction and the MIL coming on.
6. Install the exhaust manifold cover (upper). Then tighten the bolts to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
7. Installation of the remaining components is in the reverse order of removal.
ALBIA0889GB
Tool numbers : KV991J0050 (J-44626) : KV10117100 (J-36471-A)
ALBIA0919GB
ALBIA0888GB
Revision: November 20132014 Altima NAM

EM-50
< REMOVAL AND INSTALLATION >[QR25DE]
CAMSHAFT
12. Loosen the camshaft bracket bolts in the order as shown, and
remove the camshaft brackets and camshafts.
NOTE:
Remove No.1 camshaft bracket by slightly tapping it with a rub-
ber mallet.
13. Remove the valve lifters. NOTE:
Check mounting positions, and set them aside in the order removed.
INSPECTION AFTER REMOVAL
Oil Filter
• Check that there is no foreign material on the oil filter (1) and check for clogging.
• Check the oil filter for damage.
• If there is damage, replace the oil filter.
Camshaft Runout
1. Put the camshaft on a V-block supporting the No.2 and No.5 journals.
CAUTION:
Do not support the No. 1 journal (on the side of the cam-
shaft sprocket) because it has different diameter from the
other four locations.
2. Set the dial gauge (A) vertically on the No.3 journal.
3. Turn camshaft in one direction by hand, and measure the cam- shaft runout on the dial gauge total indicator reading.
Camshaft Cam Height
1. Measure the camshaft cam height using suitable tool (A).
2. If wear is beyond the limit, replace the camshaft.
Camshaft Journal Clearance
Outer Diameter of Camshaft Journal
(A) : Intake side
(B) : Exhaust side
: Engine front
ALBIA0846GB
ALBIA0945ZZ
Standard : Less than 0.02 mm (0.0008 in)PBIC3177J
Standard intake cam height : 45.865 - 46.055 mm (1.8057 - 1.8132 in)
Standard exhaust cam height : 44.175 - 44.365 mm (1.7392 - 1.7467 in)
PBIC3178J
Revision: November 20132014 Altima NAM

OIL SEALEM-71
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
2. Press in valve oil seal to the position shown using Tool (A).
3. Installation of the remaining components is in the reverse order of removal.
Removal and Installati on of Front Oil SealINFOID:0000000009460501
REMOVAL
1. Remove the RH front wheel. Refer to WT-55, "Adjustment".
2. Remove the fender protector side cover (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and
Installation".
3. Remove the drive belt. Refer to EM-19, "Removal and Installation"
.
4. Remove the rear cover plate.
5. Remove crankshaft pulley (1) using the following procedure:
a. Hold the crankshaft pulley (1) using suitable tool (A), then loosen and remove the crankshaft pulley bolt.
b. Attach suitable tool (A) in the M 6 (0.24 in diameter) thread hole
on crankshaft pulley (1), and remove crankshaft pulley.
6. Remove front oil seal from front cover. CAUTION:
Be careful not to damage the front cover.
INSTALLATION
1. Apply new engine oil to new front oil seal lip and install it using a suitable tool.
• Install new oil seal in the direction shown.Oil seal installed height
(H) : 12.1 mm (0.476 in)
Tool number : KV10115600 (J-38958)
ALBIA0864GB
ALBIA0857GB
ALBIA0858GB
(A) : Dust seal lip
(B) : Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
Revision: November 20132014 Altima NAM

EM-78
< REMOVAL AND INSTALLATION >[QR25DE]
CYLINDER HEAD
4. Install new valve oil seal using Tool (A) as shown.
5. Install valve. • Install larger diameter to intake side.
6. Install valve spring with valve spring seat (1). • Install valve spring so that the identification color faces upward
(A).
• Install smaller pitch to cylinder head side (B).
• Confirm the identification color of the valve spring.
• Intake: white
• Exhaust: light blue
7. Install valve spring retainer.
8. Install valve collet. • Compress valve spring using Tools. Install valve collet with amagnet hand.
CAUTION:
When working take care not to damage valve lifter holes.
• Tap valve stem edge lightly with a plastic hammer after instal-
lation to check its installed condition.
9. Install valve lifter.
10. Install spark plug tube.
a. Remove old liquid gasket from cylinder head mounting hole.
b. Apply liquid gasket all around on spark plug tube with a 12 mm (0.47 in) width from edge of spark plug tube on the press fit side.
• Use Three Bond or equivalent. Refer to GI-21, "Recom-
mended Chemical Products and Sealants".
c. Press fit spark plug tube so that height (H) is as shown.
CAUTION:
• When press fitting be careful not to deform spark plug
tube.
• After press fitting, wipe off any protruding liquid gasket on top surface of cylinder head.
Inspection After DisassemblyINFOID:0000000009460506
CYLINDER HEAD DISTORTION
Oil seal installed height (H) : 12.1 mm (0.476 in)
Tool number : KV10115600 (J-38958)
ALBIA0864GB
JPBIA4479ZZ
Tool number (A) : KV10116200 (J-26336-A)
Tool number (B) : KV10109220 ( — )
Tool number (C) : KV10115900 (J-26336-20)
JPBIA1365ZZ
Press fit height (H) standard value : 41.7 mm (1.642 in)
ALBIA0870GB
Revision: November 20132014 Altima NAM

EM-82
< REMOVAL AND INSTALLATION >[QR25DE]
CYLINDER HEAD
VALVE SPRING SQUARENESS
Set try square (A) along the side of the valve spring and rotate the
spring. Measure the maximum clearance between the top face of the
spring and the try square.
CAUTION:
Do not remove the valve spring seat from the valve spring
NOTE:
If the valve spring exceeds the limi t, replace the valve spring with the
valve spring seat.
VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD
Check valve spring pressure with valve spring seat installed at spec-
ified spring height. Replace if not within specifications.
CAUTION:
Do not remove the valve spring seat.
(B) : Contact
Limit : Refer to EM-111, "Standard and Limit".
JPBIA4391ZZ
Standard : Refer to EM-111, "Standard and Limit".
SEM113
Revision: November 20132014 Altima NAM

EM-104
< UNIT DISASSEMBLY AND ASSEMBLY >[QR25DE]
CYLINDER BLOCK
Method of Using Plastigage
• Remove oil and dust on the crankshaft journal and the surfaces of
each bearing completely.
• Cut the Plastigage slightly shorter than the bearing width, and
place it in crankshaft axial direction, avoiding oil holes.
• Tighten the main bearing bolts to the specified torque. CAUTION:
Do not rotate the crankshaft.
• Remove the bearing cap and bearings, and using the scale on the Plastigage bag, measure the Plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the "Method by Calculation".
CRUSH HEIGHT OF MAIN BEARING
• When the bearing cap is removed after being tightened to the specified torque with main bearings installed, the tip end of bearing
must protrude.
• If the standard is not met, replace main bearings.
OUTER DIAMETER OF LOWER CYLINDER BLOCK BOLT
• Perform only with M10 (0.39 in) bolts.
• Measure outer diameters (d1, d2) at two positions as shown.
• Measure d2 at a point within area (A) as shown.
• When the value of d1- d2 exceeds the limit (a large difference in dimensions), replace the bolt with a new one.
OUTER DIAMETER OF CONNECTING ROD BOLT
• Measure outer diameter (d) at position as shown.
• When (d) exceeds the limit (when it becomes thinner), replace the
bolt with a new one.
EM142
Standard : There must be crush height.
SEM502G
Limit : 0.13 mm (0.0051 in)
PBIC0272E
Limit : 7.75 mm (0.3051 in) or less
PBIC0273E
Revision: November 20132014 Altima NAM

EM-112
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*2: When the intake or exhaust valve opening angle is at the maximum.
*3: When starting the engine with engine coolant temperature 60
°C (140 °F) or less.
DRIVE BELTS
EXHAUST MANIFOLD
Unit: mm (in)
SPARK PLUG
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
CYLINDER HEAD
Unit: mm (in)
VA LV E
Valve Dimensions
Unit: mm (in)
Tension of drive belts Auto adjustment by drive belt auto-tensioner
Surface distortion Description Limit
Exhaust manifold 0.3 (0.012)
Make DENSO
Type* Standard FXE20HE11C
Gap (nominal) 1.1 (0.043)
Description Limit
Head surface distortion 0.1 (0.004)
Description Standard
Spark plug tube installation height 41.7 (1.642)
PBIC0283E
Valve head diameter (D) Intake 35.5 - 35.8 (1.398 - 1.409)
Exhaust 30.3 - 30.6 (1.193 - 1.205)
SEM188
Revision: November 20132014 Altima NAM

EM-114
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*: Always check with the Parts Department for the latest parts information.
Valve Spring
Valve Lifter
Unit: mm (in)
Valve Oil Seal
Unit: mm (in)
Valve Guide
3.38 (0.1331) 338H
3.40 (0.1339) 340H
3.42 (0.1346) 342H
3.44 (0.1354) 344H
3.46 (0.1362) 346H
3.48 (0.1370) 348H
3.50 (0.1378) 350H Thickness Identification mark (Stamp)*
KBIA0119E
Free height standard
mm (in) Intake 47.92 - 48.12 (1.8866 - 1.8945)
Exhaust 48.65 - 48.85 (1.9154 - 1.9232)
Installation height mm (in) Intake 36.96 (1.4551)
Exhaust 36.96 (1.4551)
Installation load N (kg - f, lb–f) Intake 151 - 175 (15.4 - 17.8, 34 - 39)
Exhaust 151 - 175 (15.4 - 17.8, 34 - 39)
Height during valve open mm (in) Intake 26.76 (1.0535)
Exhaust 28.46 (1.1205)
Load with valve open N (kg-f, lb-f) Intake 335 - 383 (34.2 - 39.1, 75.3 - 86.1)
Exhaust 300 - 342 (30.6 - 34.9, 67.4 - 76.9)
Identification color Intake White
Exhaust Light blue
Out-of-square mm (in) 1.0 (0.0394) 1.0 (0.0394)
Description Standard
Valve lifter outer diameter 33.977 - 33.987 (1.3377 - 1.3381)
Valve lifter bore inner diameter 34.000 - 34.021 (1.3386 - 1.3394)
Clearance between lifter and lifter guide 0.013 - 0.044 (0.0005 - 0.0017)
Description Standard
Valve oil seal installation height (A) 12.1 (0.476)
Revision: November 20132014 Altima NAM

EM-116
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*1 Machining data
CAMSHAFT AND CAMSHAFT BEARING
Unit: mm (in)
*: Total indicator reading
CYLINDER BLOCK
Angle (
α1) Intake 60
°
Exhaust 60 °
Angle ( α2) Intake 88
° 46' - 90 ° 14'
Exhaust 88 ° 46' - 90 ° 14'
Angle ( α3) Intake 120
°
Exhaust 120 °
Contacting width (W)*1 Intake 0.99 - 1.35 (0.0390 - 0.0531)
Exhaust 1.19 - 1.55 (0.0469 - 0.0610)
Standard
Camshaft runout [TIR*] Less than 0.02 (0.0008)
Cam height (A) Intake 45.865 - 46.055 (1.8057 - 1.8132)
Exhaust 44.175 - 44.365 (1.7392 - 1.7467)
Outer diameter of camshaft journal No. 1
27.935 - 27.955 (1.0998 - 1.1006)
No. 2, 3, 4, 5
23.435 - 23.455 (0.9226 - 0.9234)
Inner diameter of camshaft bracket No.1
28.000 - 28.021 (1.1024 - 1.1032)
No.2, 3, 4, 5
23.500 - 23.521 (0.9252 - 0.9260)
Camshaft journal clearance 0.045 - 0.086 (0.0018 - 0.0034)
Camshaft end play 0.115 - 0.188 (0.0045 - 0.0074)
Camshaft sprocket runout [TIR*] Less than 0.15 (0.0059)
SEM671
Revision: November 20132014 Altima NAM

EM-152
< REMOVAL AND INSTALLATION >[VQ35DE]
EXHAUST MANIFOLD AND THREE WAY CATALYST
Removal and Installation (LH)
INFOID:0000000009460546
REMOVAL
WARNING:
• Perform the work when the exhaust system has completely cooled down.
• When removing the front and rear engine mounting th rough bolts and nuts, lift the engine up slightly
for safety.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove the air cleaner assembly, and air duct hose and resonator assembly. Refer to EM-144, "Removal
and Installation".
2. Remove the battery and battery tray assembly. Refer to PG-74, "Removal and Installation (Battery Tray)"
.
3. Remove the engine under cover. Refer to EXT-28, "Removal and Installation"
.
4. Remove the radiator assembly. Refer to CO-41, "Removal and Installation"
.
5. Remove the engine cooling fan shroud and motor assembly. Refer to CO-42, "Removal and Installation"
.
6. Remove the front exhaust tube. Refer to EX-10, "Exploded View"
.
7. Remove the LH three way catalyst support brackets.
8. Remove heated oxygen sensor 2 (bank 2), air fuel ratio (A/F) sensor 1 (bank 2).
a. Remove harness connector of each sensor, and di sconnect the harness from the bracket and middle
clamp.
b. Remove both heated oxygen sensor 2 and air fuel ratio (A/F) sensor 1 using Tool.
CAUTION:
• Be careful not to damage heated oxygen sen sors 2 or air fuel ratio (A/F) sensors 1.
• Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a co ncrete floor; replace with a new sensor.
9. Remove exhaust manifold heat shield (LH) and three way catalyst heat shields (LH) using power tool.
10. Remove the three way catalyst (bank 2) by loosening the bolts first and then removing the nuts and through bolts.
11. Loosen and remove the exhaust manifold nuts in the reverse order as shown.
NOTE:
Number 7 and 8 are not applicable to removal.
12. Remove the exhaust manifold (LH) and gasket.
INSPECTION AFTER REMOVAL
Surface Distortion Tool numbers : KV10114400 (J-38365)
: KV991J0050 (J-44626)
: Engine front
AWBIA1208GB
Revision: November 20132014 Altima NAM