lock NISSAN TEANA 2014 Service Manual

PWC-48
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
ENCODER
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unl ock switch and front power window motor LH.
3. Check continuity between main power window and door lock/unlock switch connector D12 and front power window motor connector D9.
4. Check continuity between main power window and door lock/unlock switch connector D12 and ground.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-49, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH.
3. Check continuity between front power window motor LH connector D9 and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5. CHECK HARNESS CONTINUITY 2
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch connector D12 and front
power window motor LH connector D9.
Is the inspection result normal?
YES >> Check main power window and door lock/unlock switch. Refer to PWC-33, "POWER WINDOW
MAIN SWITCH : Component Inspection".
NO >> Repair or replace the harness or connectors.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect main power window and door lock/unlock switch.
Te r m i n a l
Vo l ta g e
(Approx.)
(+)
(–)
Front power window motor LH connector Terminal
D9 2 Ground 10
Main power window and door lock/unlock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D12 14 D9 2 Yes
Main power window and door lock/unlock switch con- nector Te r m i n a l
GroundContinuity
D12 14 No
Front power window motor LH connector Terminal GroundContinuity
D9 4 Yes
Main power window and door lock/un- lock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D12 12D94Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-49
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
2. Check continuity between main power window D12 and door lock/unlock switch connector and front
power window motor LH connector D9.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-49, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
DRIVER SIDE : Special Repair RequirementINFOID:0000000009460868
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACIN G CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> Inspection end.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
Main power window and door lock/unlock
switch connector Te r m i n a lFront power window motor
LH connector Terminal Continuity
D12 4
D9 6
Ye s
55
Main power window and door lock/unlock switch connector Te r m i n a l
GroundContinuity
D12 4
No
5
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-52
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW LOCK SWITCH
POWER WINDOW LOCK SWITCH
DescriptionINFOID:0000000009460873
Ground circuit of main power window and door lock/unlock
switch shuts off if power window lock switch of
main power window and door lock/unlock switch is operated. This inhibits all operation, except for the main
switch.
Component Function CheckINFOID:0000000009460874
1. CHECK POWER WINDOW LOCK SIGNAL
Exchanges for a normal main power window and door lock/unlock switch, and operation is checked.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-52, "Special Repair Requirement".
NO >> Check condition of harness and connector.
Special Repair RequirementINFOID:0000000009460875
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Repair Requirement".
Is the inspection result normal?
YES >> Inspection end.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOWS DO NOT OPERATE WITH ANY POWER WINDOW SWITCH-
ES
PWC-53
< SYMPTOM DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
SYMPTOM DIAGNOSIS
POWER WINDOWS DO NOT OPERATE WITH ANY POWER WINDOW
SWITCHES
Diagnosis ProcedureINFOID:0000000009460876
1. CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
Refer to BCS-74, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2. CHECK MAIN POWER WINDOW A ND DOOR LOCK/UNLOCK SWITCH
Check main power window and door lock/unlock switch.
Refer to PWC-33, "POWER WINDOW MAIN SWITCH : Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH POWER SUPPLY AND
GROUND CIRCUIT
Check main power window and door lock/unlock switch power supply and ground circuit.
Refer to PWC-30, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPERATE
PWC-55
< SYMPTOM DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPER-
AT E
Diagnosis ProcedureINFOID:0000000009460878
1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Check power window and door lock/unlock switch RH.
Refer to PWC-34, "FRONT POWER WINDOW SW ITCH : Component Function Check"
.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2. CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
Check front power window motor RH circuit.
Refer to PWC-42, "PASSENGER SIDE : Component Function Check"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOW LOCK SWITCH DOES NOT FUNCTIONPWC-61
< SYMPTOM DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis ProcedureINFOID:0000000009460884
1.REPLACE MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Replace main power window and door lock/unlock switch.
Refer to PWC-65, "Removal and Installation"
. After that, PWC-27, "ADDITIONAL SERVICE WHEN REPLAC-
ING CONTROL UNIT : Special Repair Requirement".
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-62
< SYMPTOM DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
DOOR KEY CYLINDER SWITCH DOES
NOT OPERATE POWER WINDOWS
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WIN-
DOWS
Diagnosis ProcedureINFOID:0000000009460885
1.PERFORM INITIALIZATION PROCEDURE
Initialization procedure is performed and operation is confirmed.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 2.
2.CHECK FRONT DOOR LOCK ASSEMBLY LH (DOOR KEY CYLINDER SWITCH)
Check front door lock assembly LH (door key cylinder switch).
Refer to PWC-52, "Component Function Check"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 1.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCHPWC-65
< REMOVAL AND INSTALLATION > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
REMOVAL AND INSTALLATION
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Removal and InstallationINFOID:0000000009460888
REMOVAL
1. Remove the front door pull handle outer finisher using a suitable tool.
2. Release the pawls using a suitable tool and lift the main power window and door lock/unlock switch and
finisher as an assembly by starting at the rear, then pull upward and remove.
3. Disconnect the harness connector from the main power window and door lock/unlock switch.
4. Release the four pawls (two on each side) using a suitable tool, then separate the main power window and door lock/unlock
switch (1) from the main power window and door lock switch fin-
isher (2).
: Pawl
CAUTION:
Do not bend back the pawls on th e switch finisher too far or
breakage may occur.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When the main power window and door lock/unlock switch is disconnected from the harness connector it is
necessary to perform the initialization procedure. Refer to PWC-27, "ADDITIONAL SERVICE WHEN REMOV-
ING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".
ALKIA2630ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-66
< REMOVAL AND INSTALLATION >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
POWER WINDOW AND DOOR
LOCK/UNLOCK SWITCH RH
Removal and InstallationINFOID:0000000009460889
REMOVAL
1. Remove the front door pull handle outer finisher using a suitable tool.
2. Release the pawls using a suitable tool and lift t he power window switch and door lock/unlock switch RH
finisher as an assembly by starting at the rear, then pull upward and remove.
3. Disconnect the harness connector from the power window and door lock/unlock switch RH.
4. Release the four pawls (two on each side) using a suitable tool, then separate the power window and door lock/unlock switch
RH (1) from the power window and door lock/unlock switch RH
finisher (2).
: Pawl
CAUTION:
Do not bend back the pawls on the switch finisher too far or
breakage may occur.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2630ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-70
< SYSTEM DESCRIPTION >[LH & RH FRONT ANTI-PINCH]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000009460894
Component DescriptionINFOID:0000000009460895
FRONT WINDOW ANTI-PINCH SYSTEM
AWKIA2029ZZ
1. BCM (view with combination meter
removed) 2. Front power window motor LH (RH
similar) 3. Rear power window motor LH (RH
similar)
4. Main power window and door lock/ unlock switch 5. Power window and door lock/unlock
switch RH 6. Rear power window switch LH (RH
similar)
7. Front door lock assembly LH (key cylinder switch) 8. Front door switch LH (RH similar)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM