lock NISSAN TEANA 2014 Service Manual

PWC-110
< DTC/CIRCUIT DIAGNOSIS >[LH & RH FRONT ANTI-PINCH]
POWER WINDOW MOTOR
Is the inspection result normal?
YES >> Check rear power window switch LH. Refer to
PWC-103, "REAR POWER WINDOW SWITCH :
Component Inspection".
NO >> Repair or replace the harness or connectors.
3. CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to PWC-110, "REAR LH : Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace rear power window motor LH. Refer to GW-25, "Removal and Installation"
.
REAR LH : Component InspectionINFOID:0000000009460939
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR LH
Check motor operation by connecting the battery voltage directly to rear power window motor LH D204.
Is the inspection result normal?
YES >> Rear power window motor LH is OK.
NO >> Replace rear power window motor LH. Refer to GW-25, "Removal and Installation"
.
REAR RH
REAR RH : DescriptionINFOID:0000000009460940
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
rear power window switch RH.
REAR RH : Component Function CheckINFOID:0000000009460941
1. CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
Check rear power window motor RH operation with operat ing main power window and door lock/unlock switch
or rear power window switch RH.
Is the inspection result normal?
YES >> Rear power window motor RH is OK.
NO >> Refer to PWC-110, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis ProcedureINFOID:0000000009460942
Regarding Wiring Diagram information, refer to PWC-83, "Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch".
Rear Power Window Motor RH Circuit Check
1. CHECK REAR POWER WINDOW SWITCH RH OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor RH.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor RH connector D304 and ground.
Te r m i n a l Motor condition
(+) (–)
31 DOWN
13 UP
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-113
< DTC/CIRCUIT DIAGNOSIS > [LH & RH FRONT ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
ENCODER
DRIVER SIDE
DRIVER SIDE : DescriptionINFOID:0000000009460944
Detects condition of the front power window motor LH operation and transmits to main power window and door
lock/unlock switch as pulse signal.
DRIVER SIDE : Componen t Function CheckINFOID:0000000009460945
1. CHECK ENCODER OPERATION
Check front door glass LH perform AUTO open/close operation normally when operating main power window
and door lock/unlock switch.
Is the inspection result normal?
YES >> Encoder operation is OK.
NO >> Refer to PWC-113, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diag nosis ProcedureINFOID:0000000009460946
Regarding Wiring Diagram information, refer to PWC-83, "Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch".
Encoder Circuit Check
1. CHECK ENCODER OPERATION
1. Turn ignition switch ON.
2. Check signal between main power window and door lock/unlock switch connector D7 and ground with
oscilloscope.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 2.
2. CHECK FRONT POWER WINDOW MOTOR LH POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between front power window motor LH connector D9 and ground.
Te r m i n a l s
Signal
(Reference value)
(+)
(–)
Main power window and door lock/un-
lock switch connector Te r m i n a l
D7 4
Ground Refer to following signal
5
AWKIA2032GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-114
< DTC/CIRCUIT DIAGNOSIS >[LH & RH FRONT ANTI-PINCH]
ENCODER
Is the measurement value within the specification?
YES >> GO TO 4.
NO >> GO TO 3.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unl ock switch and front power window motor LH.
3. Check continuity between main power window and door lock/unlock switch connector D7 and front power
window motor LH connector D9.
4. Check continuity between main power window and door lock/unlock switch connector D7 and ground.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-142, "Removal and
Installation". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CON-
TROL UNIT : Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH.
3. Check continuity between front power window motor LH connector D9 and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5. CHECK HARNESS CONTINUITY 2
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch connector D7 and front power
window motor LH connector D9.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-142, "Removal and
Installation". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CON-
TROL UNIT : Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
6. CHECK HARNESS CONTINUITY 3
Te r m i n a l
Voltag e
(Approx.)
(+)
(–)
Front power window motor LH
connector Te r m i n a l
D9 2 Ground 10
Main power window and door lock/ unlock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D7 14 D9 2 Yes
Main power window and door lock/unlock switch connector Te r m i n a l
Ground Continuity
D7 14 No
Front power window motor LH connector Terminal GroundContinuity
D9 4 Yes
Main power window and door lock/un- lock switch connector Te r m i n a l
Front power window motor LH
connector Terminal Continuity
D7 12 D9 4 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-115
< DTC/CIRCUIT DIAGNOSIS > [LH & RH FRONT ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch connector D7 and front power
window motor LH connector D9.
3. Check continuity between main power window and door lock/unlock switch connector D7 and ground.
Is the inspection result normal?
YES >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-93, "ADDITIONAL SERVICE WH EN REPLACING CONTROL UNIT :
Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
PASSENGER SIDE
PASSENGER SIDE : DescriptionINFOID:0000000009460947
Detects condition of the front power window motor RH operation and transmits to power window and door
lock/unlock switch RH as pulse signal.
PASSENGER SIDE : Comp onent Function CheckINFOID:0000000009460948
1.CHECK ENCODER OPERATION
Check front door glass RH perform AUTO open/close operation normally when operating power window and
door lock/unlock switch RH.
Is the inspection result normal?
YES >> Encoder operation is OK.
NO >> Refer to PWC-115, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Dia gnosis ProcedureINFOID:0000000009460949
Regarding Wiring Diagram information, refer to PWC-83, "Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch".
1. CHECK ENCODER SIGNAL
1. Connect front power window motor RH.
2. Turn ignition switch ON.
3. Check signal between power window and door lock/unlock switch RH connector D105 and ground with oscilloscope.
Main power window and door lock/un-
lock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D7 5
D9 5
Ye s
46
Main power window and door lock/unlock switch connector Te r m i n a l
GroundContinuity
D7 5
No
4
Te r m i n a l s
Signal
(Reference value)
(+)
(–)
Power window and door lock/unlock
switch RH
connector Te r m i n a l
D105 9
Ground Refer to following signal
10
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-116
< DTC/CIRCUIT DIAGNOSIS >[LH & RH FRONT ANTI-PINCH]
ENCODER
Is the inspection result normal?
YES >> Check intermittent incident. Refer to
GI-43, "Intermittent Incident".
NO >> GO TO 2.
2. CHECK FRONT POWER WINDOW MOTOR RH POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between front power window motor RH connector D105 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH and front power window motor RH.
3. Check continuity between power window and door lock/unlock switch RH connector D105 and front power
window motor RH connector D104.
4. Check continuity between power window and door lock/unlock switch RH connector D105 and ground.
Is the inspection result normal?
YES >> Replace power window and door lock/unlock switch RH. Refer to PWC-143, "Removal and Instal-
lation". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window motor RH.
3. Check continuity between front power window motor RH connector D104 and ground.
Is the inspection result normal?
ALKIA2581GB
Te r m i n a l
Vol tag e
(Approx.)
(+)
(–)
Front power window motor RH con-
nector Te r m i n a l
D105 5 Ground 10
Power window and door lock/unlock switch RH connector Te r m i n a l
Front power window motor RH
connector Terminal Continuity
D105 5 D104 2 Yes
Power window and door lock/unlock switch RH connector Te r m i n a l
Ground Continuity
D105 5 No
Front power window motor RH connector Terminal GroundContinuity
D104 4 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-117
< DTC/CIRCUIT DIAGNOSIS > [LH & RH FRONT ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
YES >> GO TO 6.
NO >> GO TO 5.
5. CHECK HARNESS CONTINUITY 2
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between power window and door lock/unlock switch RH connector D105 and front power window motor RH connector D104.
Is the inspection result normal?
YES >> Replace power window and door lock/unlock switch RH. Refer to PWC-143, "Removal and Instal-
lation". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between power window and door lock/unlock switch RH connector D105 and front power window motor RH connector D104.
3. Check continuity between power window and door lock/unlock switch RH connector D105 and ground.
Is the inspection result normal?
YES >> Replace front power window motor RH. Refer to GW-16, "Removal and Installation - Front Regu-
lator". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
NO >> Repair or replace the harness or connectors.
Power window and door lock/unlock
switch RH connector Te r m i n a lFront power window motor RH
connector Terminal Continuity
D105 4 D104 4 Yes
Power window and door lock/un- lock switch RH connector Te r m i n a lFront power window motor RH
connector Terminal Continuity
D105 9
D104 5
Ye s
10 6
Power window and door lock/unlock switch RH connector Te r m i n a l
Ground Continuity
D105 9
No
10
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-120
< DTC/CIRCUIT DIAGNOSIS >[LH & RH FRONT ANTI-PINCH]
DOOR KEY CYLINDER SWITCH
DOOR KEY CYLINDER SWITCH
DescriptionINFOID:0000000009460954
Power window main switch detects condition of the door
key cylinder and transmits to BCM as the LOCK or
UNLOCK signals.
Component Function CheckINFOID:0000000009460955
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DAT A MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT. Refer to BCS-15, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES >> Key cylinder switch is OK.
NO >> Refer to PWC-120, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009460956
Regarding Wiring Diagram information, refer to PWC-83, "Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch".
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/unlock switch connector D7 and ground.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. After that, refer to PWC-122, "Special
Repair Requirement".
NO >> GO TO 2.
2. CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and front door lock assembly LH (key cylin- der switch).
3. Check continuity between main power window and door lock/unlock switch connector D7 and front door
lock assembly LH (key cylinder switch) connector D14.
Monitor item Condition
KEY CYL LK-SW Lock : ON
Neutral / Unlock : OFF
KEY CYL UN-SW Unlock : ON
Neutral / Lock : OFF
Te r m i n a l s
Key positionVoltag e
(Approx.)
(+)
(–)
Main power window and door
lock/unlock switch connector Te r m i n a l
D7 3
Ground Lock 0
Neutral/Unlock 5
15 Unlock 0
Neutral/Lock 5
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR KEY CYLINDER SWITCHPWC-121
< DTC/CIRCUIT DIAGNOSIS > [LH & RH FRONT ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
4. Check continuity between main power window and door lock/unlock switch connector D7 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between front door lock assembly LH (key cylinder switch) connector D14 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness or connectors.
4. CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
Refer to PWC-121, "Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace front door lock assembly LH (door key cylinder switch). After that, refer to PWC-122,
"Special Repair Requirement".
Component InspectionINFOID:0000000009460957
COMPONENT INSPECTION
1. CHECK DOOR KEY CYLINDER SWITCH
Check front door lock assembly LH (key cylinder switch) D14.
Is the inspection result normal?
YES >> Key cylinder switch is OK.
NO >> Replace front door lock assembly LH (key cylinder switch). After that, refer to PWC-122, "Special
Repair Requirement".
Main power window and door lock/
unlock switch connector Te r m i n a l
Front door lock assembly LH (key
cylinder switch) connector Terminal Continuity
D7 3
D14 6
Ye s
15 5
Main power window and door lock/unlock switch connector Te r m i n a l
Ground Continuity
D7 3
No
15
Front door lock assembly LH (key cylinder switch) con-
nector Te r m i n a l
GroundContinuity
D14 4 Yes
Te r m i n a l Key position Continuity
Front door lock assembly LH (key cylinder switch)
connector
5 4 Unlock Yes
Neutral/Lock No
6 Lock Yes
Neutral/Unlock No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOW SERIAL LINKPWC-123
< DTC/CIRCUIT DIAGNOSIS > [LH & RH FRONT ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
POWER WINDOW SERIAL LINK
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : DescriptionINFOID:0000000009460959
Main power window and door lock/unlock switch, pow er window and door lock/unlock switch RH and BCM
transmit and receive the signal by power window serial link.
The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and
power window and door lock/unlock switch RH
• Keyless power window down signal
The signal mentioned below is transmitted from main pow er window and door lock/unlock switch to power win-
dow and door lock/unlock switch RH
• Front door window RH operation signal
• Power window control by key cylinder switch signal
• Power window lock switch signal
• Retained power operation signal
POWER WINDOW MAIN SWITCH : Component Function CheckINFOID:0000000009460960
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “D ATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT. Refer to BCS-15, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES >> Power window serial link is OK.
NO >> Refer to PWC-123, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
.
POWER WINDOW MAIN SWITCH : Diagnosis ProcedureINFOID:0000000009460961
Regarding Wiring Diagram information, refer to PWC-83, "Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch".
Power Window Serial Link Check
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Remove Intelligent Key, and close front door LH and RH.
2. Check signal between BCM connector and ground wit h oscilloscope when door lock and unlock switch
(LH and RH) is turned to “LOCK” or “UNLOCK”.
3. Check that signals which are shown in the figure below can be detected during 10 second just after door
lock and unlock switch (LH and RH) is turned to “LOCK” or “UNLOCK”.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-124
< DTC/CIRCUIT DIAGNOSIS >[LH & RH FRONT ANTI-PINCH]
POWER WINDOW SERIAL LINK
Is the inspection result normal?
YES >> Power window serial link is OK.
NO >> GO TO 2.
2. CHECK POWER WINDOW SERIAL LINK CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and main power window and door lock/unlock switch.
3. Check continuity between BCM connector M18 and ma in power window and door lock/unlock switch con-
nector D7.
4. Check continuity between BCM connector M18 and ground.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-142, "Removal and
Installation". After that, refer to PWC-93, "ADDITIONAL SERVICE WHEN REPLACING CON-
TROL UNIT : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
FRONT POWER WINDOW SWITCH
FRONT POWER WINDOW SWITCH : DescriptionINFOID:0000000009460962
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM
transmit and receive the signal by power window serial link.
The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and
power window and door lock/unlock switch RH
• Keyless power window down signal
The signal mentioned below is transmitted from main power window and door lock/unlock switch to power win-
dow and door lock/unlock switch RH
• Front door window RH operation signal
• Power window control by key cylinder switch signal
• Retained power operation signal
• Power window lock switch signal
FRONT POWER WINDOW SWITCH : Component Function CheckINFOID:0000000009460963
1. CHECK POWER WINDOW AND DOOR LO CK/UNLOCK SWITCH RH OUTPUT SIGNAL
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “D ATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT. Refer to BCS-15, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Te r m i n a l
Signal
(Reference value)
(+)
(–)
BCM connector Terminal
M18 54 Ground
PIIA1297E
BCM connector Terminal Main power window and door lock/unlock
switch connector Terminal Continuity
M18 54 D7 11 Yes
BCM connector Terminal GroundContinuity
M18 54 No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM