seats NISSAN TEANA 2014 Workshop Manual

FRONT SEATSE-23
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
REMOVAL AND INSTALLATION
FRONT SEAT
DRIVER SIDE
DRIVER SIDE : Exploded ViewINFOID:0000000009462933
DRIVER SEAT - POWER
ALJIA0955ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-25
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
DRIVER SEAT - MANUAL
ALJIA0956ZZ
1. Seat cushion trim 2. Seat cushion pad 3. Seat cushion heater (if equipped)
4. Seat cushion outer finisher (RH) 5. Seat cushion inner finisher (RH front)6. Seat cushion inner finisher (RH rear)
7. Rear slide cover (RH) 8. Seat belt buckle 9. Slide cover (RH)
10. Front slide cover (RH) 11. Front slide cover (LH) 12. Seat harness
13. Seat frame assembly 14. Slide cover (LH) 15. Seat cushion outer finisher (LH)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-27
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
DRIVER SIDE : Removal and Installation - Seatback BoardINFOID:0000000009462935
REMOVAL
CAUTION:
• Before servicing, turn ignition swit ch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
1. Slide the seat to the full forward position.
2. Disconnect the negative and positive battery terminal s and wait at least three minutes. Refer to PG-73,
"Removal and Installation (Battery)".
3. Remove the seatback board (1). NOTE:
The back side of the seatback boar d is shown to assist with
identifying fastener location.
a. Release the two bottom clips (A) using a suitable tool. : Clip
b. Insert fingers into sides ( ) and pull out the seatback board, while pressing the side clips (B) to release it from the seatback
frame.
c. Pull the seatback board down releasing the upper hooks (C) and remove.
INSTALLATION
Installation is in the reverse order of removal.
DRIVER SIDE : Removal and Installation - Lumbar Support AssemblyINFOID:0000000009462936
REMOVAL
WARNING:
Do not leave any objects (screwdriver s, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn ignition swit ch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
1. Slide the seat to the full forward position.
2. Disconnect the negative and positive bat tery terminals, then wait at least three minutes. Refer to PG-73,
"Removal and Installation (Battery)".
3. Remove the seatback board. Refer to SE-27, "DRIVER SIDE : Removal and Installation - Seatback
Board".
ALJIA0930ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-29
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
PASSENGER SIDE : Exploded ViewINFOID:0000000009462937
PASSENGER SEAT
AWJIA1227ZZ
1. Seat cushion trim 2. Seat cushion pad 3. Seat cushion heater (if equipped)
4. Side air bag module 5. Recline lever 6. Seat cushion outer finisher (RH)
7. Seat cushion inner finisher (RH front) 8. Seat cushion inner finisher
(RH rear) 9. Rear slide cover (RH)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-31
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
• When installing the RH front seat, tighten the bolts in the order shown.
PASSENGER SIDE : Removal and In stallation - Seatback BoardINFOID:0000000009462939
WARNING:
Do not leave any objects (screwdriver s, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn ignition swit ch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
REMOVAL
1. Disconnect the negative and positive battery terminals and wait a least three minutes. Refer to PG-73,
"Removal and Installation (Battery)".
2. Slide the seat to the full forward position.
3. Remove the seatback board (1). NOTE:
The back side of the seatback boar d is shown to assist with
identifying fastener location.
a. Release the two bottom clips (A) using a suitable tool. : Clip
b. Insert fingers into sides ( ) and pull out the seatback board, while pressing the side clips (B) to release from the seatback
frame.
c. Pull the seatback board down releasing the upper hooks (C) and remove.
INSTALLATION
Installation is in the reverse order of removal.
HEATED SEAT SWITCH
HEATED SEAT SWITCH : Removal and InstallationINFOID:0000000009462940
REMOVAL
1. Remove the CVT shift selector finisher. Refer to IP-18, "Exploded View".
RH front seat bolt torque : 49 Nm (5.0 kg-m, 36 lb-ft)
ALJIA0928ZZ
ALJIA0930ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-33
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
REAR SEAT
Exploded ViewINFOID:0000000009462941
REAR SEAT WITHOUT REMOVABLE HEADREST
ALJIA0959ZZ
1. Rear seatback assembly (RH) 2. Rear seat bolster (RH) 3. Seat belt guide (RH)
4. Seatback board (RH) 5. Seatback trim (RH) 6. Seatback pad (RH)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-35
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
REAR SEAT WITH REMOVABLE HEADREST
ALJIA0958ZZ
1. Headrest (RH) 2. Rear seat bolster (RH) 3. Seat belt guide (RH)
4. Rear seatback assembly (RH) 5. Seatback board (RH) 6. Headrest holder (RH) (free)
7. Headrest holder (RH) (locked) 8. Seatback trim (RH) 9. Seatback pad (RH)
10. Armrest 11. Cup holder 12. Armrest hinge finisher
13. Seatback hinge assembly (RH) 14. Seat cushion assembly 15. Seat cushion lock
16. Seat cushion wire cover 17. Seat cushion pad 18. Seat cushion trim
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-37
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
b. Remove the seatback pivot bolt (A). CAUTION:
Do not remove hinge bolt (B) or seatback alignment may be
necessary.
c. Release the seatback latch assembly then remove the rear seatback assembly (1) from the seatback hinge (LH) (2).
d. Remove the rear seatback assembly (LH).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten bolts and nuts to specification. Refer to SE-33, "Exploded View"
.
Removal and Installation - Seatback HingeINFOID:0000000009462944
REMOVAL
1. Remove the seat cushion assembly, rear seatback assembly (RH), and the rear seatback assembly (LH).
Refer to SE-36, "Removal and Installation - Seat Assembly"
.
2. Remove the bolt and nut from the seatback hinge assembly (RH), then remove.
3. Remove the bolt from the s eatback hinge (LH), then remove.
INSTALLATION
1. Install seatback hinge assembly (RH) and seatback hinge (LH) loosely.
2. Install the rear seatback assembly (LH) and engage into seatback latch assembly.
3. Install the rear seatback assembly (RH) and engage into seatback latch assembly.
4. Tighten seatback hinge nut and bolts to specification. Refer to SE-33, "Exploded View"
.
CAUTION:
Ensure rear seatback assemblies (LH/RH) fold and latch properly. Adjust if necessary.
5. Install remaining components in reverse order of removal.
Removal and Installation - Seatback Latch AssemblyINFOID:0000000009462945
REMOVAL
1. Remove the rear seat bolster (LH/RH). Refer to SE-38, "Removal and Installation - Rear Seat Bolster".
2. Place the rear seatback assemblies (LH/RH) in the folded down position.
3. Remove the rear parcel shelf finisher. Refer to INT-26, "Exploded View"
.
4. From trunk area release pawls (A) to open cable guide (1).
5. Unclip latch cable (2) at location (B). : Front
NOTE:
LH side shown; RH side similar.
6. Remove two seatback latch assembly bolts and the seatback latch assembly.
INSTALLATION
Installation is in the reverse order of removal.
• Tighten two seatback latch assembly bolts to specification. Refer to SE-33, "Exploded View"
.
ALJIA0940ZZ
ALJIA0948ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-39
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT SEAT
DRIVER SIDE
DRIVER SIDE : Exploded ViewINFOID:0000000009462948
DRIVER SEAT - POWER
ALJIA0955ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
DRIVER SEAT - MANUAL
ALJIA0956ZZ
1. Seat cushion trim 2. Seat cushion pad 3. Seat cushion heater (if equipped)
4. Seat cushion outer finisher (RH) 5. Seat cushion inner finisher (RH front)6. Seat cushion inner finisher (RH rear)
7. Rear slide cover (RH) 8. Seat belt buckle 9. Slide cover (RH)
10. Front slide cover (RH) 11. Front slide cover (LH) 12. Seat harness
13. Seat frame assembly 14. Slide cover (LH) 15. Seat cushion outer finisher (LH)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM