sensor NISSAN TEANA 2014 Service Manual

PRECAUTIONSEM-123
< PRECAUTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental
Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951676
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service t he system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for Draining CoolantINFOID:0000000009460515
• Drain coolant when engine is cooled.
Precaution for Disconnecting Fuel PipingINFOID:0000000009460516
• Before starting work, make sure no fire or spark producing items are in the work area.
• Release fuel pressure before disassembly.
• After disconnecting pipes, plug openings to stop fuel leakage.
Precaution for Removal and DisassemblyINFOID:0000000009460517
• When instructed to use special service tools, use the spec ified tools. Always be careful to work safely, avoid
forceful or uninstructed operations.
• Exercise maximum care to avoid damage to mating or sliding surfaces.
• Cover openings of engine system with tape or the equiva lent, if necessary, to seal out foreign materials.
• Mark and arrange disassembly parts in an organized way for easy troubleshooting and assembly.
• When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specif ied, do exactly as specified. Power tools may be used
where noted in the step.
Precaution for Inspection, Repair and ReplacementINFOID:0000000009460518
• Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Precaution for Assembly and InstallationINFOID:0000000009460519
• Use torque wrench to tighten bolts or nuts to specification.
Revision: November 20132014 Altima NAM

PREPARATIONEM-127
< PREPARATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Commercial Service ToolINFOID:0000000009460523
K V 1 0 1111 0 0
(J-37228)
Seal cutter Removing steel oil pan and rear timing chain
case
KV10112100
(BT-8653-A)
Angle wrench Tightening bolts for bearing cap, cylinder
head, etc.
KV991J0050
(J-44626)
Air fuel sensor Socket Loosening or tightening air fuel ratio A/F sen-
sor
a: 22 mm (0.87 in)
KV10114400
(J-38365)
Heated oxygen sensor wrench Loosening or tightening rear heated oxygen
sensor
a: 22 mm (0.87 in)
—
(J-50288)
Ring gear stopper Removing and installing crankshaft pulley
—
(J-47128)
Seal installer Installing rear main seal
Tool number
(TechMate No.)
Tool name Description
NT046
NT014
LBIA0444E
NT636
ALBIA0675ZZ
LBIA0452E
Revision: November 20132014 Altima NAM

PREPARATIONEM-129
< PREPARATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner Reconditioning the exhaust system threads
before installing a new oxygen sensor (Use
with anti-seize lubricant shown below.)
a: J-43897-18 (18 mm dia.) for zirconia ox-
ygen sensor
b: J-43897-12 (12 mm dia.) for titania oxy-
gen sensor
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907) Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
Tube presser Pressing the tube of liquid gasket
Tool name Description
AEM488
AEM489
NT052
Revision: November 20132014 Altima NAM

AIR CLEANER FILTEREM-137
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
AIR CLEANER FILTER
Exploded ViewINFOID:0000000009460533
Removal and InstallationINFOID:0000000009460534
REMOVAL
CAUTION:
It is not necessary to remove the front ai r duct to replace the air cleaner filter.
NOTE:
Replace the air cleaner filter per the periodic maintenance schedule or as necessary. Refer to MA-7, "FOR
USA AND CANADA : Introduction of Periodic Maintenance".
1. Unhook air cleaner case side clips and lift air cleaner case (upper).
2. Remove the air cleaner filter.
INSTALLATION
Installation is in the reverse order of removal.
1. Air duct hose and resonator assembly 2. Duct sub-cover 3. Front air duct
4. Air cleaner case (lower) 5. Grommets 6. Air cleaner case mounting bracket
7. Bracket 8. Air cleaner filter 9. Air cleaner case (upper)
10. Mass air flow sensor A. To electric throttle control actuator B. Air cleaner case side clips
AWBIA0569ZZ
Revision: November 20132014 Altima NAM

EM-144
< REMOVAL AND INSTALLATION >[VQ35DE]
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
Exploded ViewINFOID:0000000009460539
Removal and InstallationINFOID:0000000009460540
REMOVAL
1. Remove engine room cover. Refer to
EM-143, "Removal and Installation".
2. Remove duct sub-cover and front air duct.
3. Disconnect the blow-by hose.
4. Disconnect the tube clamp at the electric throttle control actuator and at the air duct hose and resonator
assembly.
5. Remove air duct hose and resonator assembly.
6. Disconnect mass air flow sensor.
7. Remove mass air flow sensor from air cleaner assembly, as necessary. CAUTION:
Handle mass air flow sensor with care.
• Do not shock it.
• Do not disassemble it.
• Do not touch its sensor.
8. Disconnect transaxle breather hose.
9. Remove air cleaner assembly.
INSPECTION AFTER REMOVAL
Inspect air cleaner case assembly, front air duct, air duct hose and resonator assembly for cracks or tears.
Replace as necessary.
1. Air duct hose and resonator assembly 2. Duct sub-cover 3. Front air duct
4. Air cleaner assembly 5. Grommets 6. Air cleaner mounting bracket
7. Bracket 8. Mass air flow sensor A. To electric throttle control actuator
ALBIA0497ZZ
Revision: November 20132014 Altima NAM

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-151
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
EXHAUST MANIFOLD AND THREE WAY CATALYST
Exploded ViewINFOID:0000000009460545
1. Gasket 2. Exhaust manifold (RH) 3. Exhaust manifold heat shield (RH)
4. Air fuel ratio sensor 1 (bank 1) 5. Ring gasket 6. Three way catalyst (bank 1)
7. Three way catalyst support (bank 1) 8. Heated oxygen sensor 2 (bank 1) 9. Three way catalyst (bank 2)
10. Three way catalyst support (bank 2) 11. Heated oxygen sensor 2 (bank 2) 12. Ring gasket
13. Exhaust manifold (LH) 14. Exhaust manifold heat sheild (LH) 15. Air fuel ratio sensor 1 (bank 2)
A. To oil pan (upper) B. Upper mark
AWBIA1356ZZ
Revision: November 20132014 Altima NAM

EM-152
< REMOVAL AND INSTALLATION >[VQ35DE]
EXHAUST MANIFOLD AND THREE WAY CATALYST
Removal and Installation (LH)
INFOID:0000000009460546
REMOVAL
WARNING:
• Perform the work when the exhaust system has completely cooled down.
• When removing the front and rear engine mounting th rough bolts and nuts, lift the engine up slightly
for safety.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove the air cleaner assembly, and air duct hose and resonator assembly. Refer to EM-144, "Removal
and Installation".
2. Remove the battery and battery tray assembly. Refer to PG-74, "Removal and Installation (Battery Tray)"
.
3. Remove the engine under cover. Refer to EXT-28, "Removal and Installation"
.
4. Remove the radiator assembly. Refer to CO-41, "Removal and Installation"
.
5. Remove the engine cooling fan shroud and motor assembly. Refer to CO-42, "Removal and Installation"
.
6. Remove the front exhaust tube. Refer to EX-10, "Exploded View"
.
7. Remove the LH three way catalyst support brackets.
8. Remove heated oxygen sensor 2 (bank 2), air fuel ratio (A/F) sensor 1 (bank 2).
a. Remove harness connector of each sensor, and di sconnect the harness from the bracket and middle
clamp.
b. Remove both heated oxygen sensor 2 and air fuel ratio (A/F) sensor 1 using Tool.
CAUTION:
• Be careful not to damage heated oxygen sen sors 2 or air fuel ratio (A/F) sensors 1.
• Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a co ncrete floor; replace with a new sensor.
9. Remove exhaust manifold heat shield (LH) and three way catalyst heat shields (LH) using power tool.
10. Remove the three way catalyst (bank 2) by loosening the bolts first and then removing the nuts and through bolts.
11. Loosen and remove the exhaust manifold nuts in the reverse order as shown.
NOTE:
Number 7 and 8 are not applicable to removal.
12. Remove the exhaust manifold (LH) and gasket.
INSPECTION AFTER REMOVAL
Surface Distortion Tool numbers : KV10114400 (J-38365)
: KV991J0050 (J-44626)
: Engine front
AWBIA1208GB
Revision: November 20132014 Altima NAM

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-153
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
• Use a reliable straightedge and f
eeler gauge to check the flatness
of the exhaust manifold mating surfaces.
• Replace the exhaust manifold if the measurement exceeds specifi- cations.
INSTALLATION
Installation is in the reverse order of removal.
1. Install the studs in the exhaust manifold (if removed), and tighten to specification.
2. Install the exhaust manifold gasket in the direction shown. CAUTION:
Do not reuse exhaust manifold gaskets.
3. Install the exhaust manifold (LH) nuts and tighten to specifica- tion in the order shown.
NOTE:
Number 7 and 8 are tightened a second time.
CAUTION:
• Before installing a heated oxyg en sensor 2 or air fuel ratio (A/F) sensor 1, clean the exhaust
manifold threads using the oxyg en sensor thread cleaner tool and apply anti-seize lubricant.
• Do not over-tighten the air fuel ratio (A/F) senso r 1 or heated oxygen sensors 2. Doing so may
cause damage.
Removal and Installation (RH)INFOID:0000000009460547
REMOVAL
WARNING: Limit : 0.3 mm (0.012 in)
PBIC1173E
Exhaust manifold studs : 15.4 N·m (1.6 kg-m, 11 ft-lb)
(A) : Bank 1
(B) : Triangle press
(C) : Bank 2
: Engine front
PBIC4954E
: Engine front
AWBIA1208GB
Oxygen sensor thread cleaner : (J-43897-18)
Oxygen sensor thread cleaner : (J-43897-12)
Tool numbers : KV10114400 (J-38365) : KV991J0050 (J-44626)
Revision: November 20132014 Altima NAM

EM-154
< REMOVAL AND INSTALLATION >[VQ35DE]
EXHAUST MANIFOLD AND THREE WAY CATALYST
• Perform the work when the exhaust and co
oling system have completely cooled down.
• When removing the front and rear engine mounting th rough bolts and nuts, lift the engine up slightly
for safety. For engine slingers, refer to EM-220, "Removal and Installation"
.
1. Remove the engine and transaxle assembly. Refer to EM-220, "Removal and Installation"
.
2. Remove the RH three way catalyst supports.
3. Remove rear engine mount bracket. Refer to EM-220, "Removal and Installation"
.
4. Remove heated oxygen sensor 2 (bank 1), air fuel ratio (A/F) sensor 1 (bank 1).
a. Remove harness connector from heated oxygen sensor 2 and air fuel ration (A/F) sensor 1, and discon-
nect the harness from the bracket and middle clamp.
b. Remove both heated oxygen sensors 2 and air fuel ratio (A/F) sensors 1 using Tool.
CAUTION:
• Be careful not to damage heated oxygen sen sors 2 or air fuel ratio (A/F) sensors 1.
• Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a co ncrete floor; replace with a new sensor.
5. Remove exhaust manifold heat shield (RH) and three way catalyst heat shields (RH) using power tool.
6. Remove the three way catalyst (bank 1) by loosening the bolts first and then removing the nuts and through bolts.
7. Loosen the exhaust manifold nuts in the reverse order as shown and remove the exhaust manifold (RH).
NOTE:
Number 7 and 8 are not applicable to removal.
INSPECTION AFTER REMOVAL
Surface Distortion
• Use a reliable straightedge and feeler gauge to check the flatness of the exhaust manifold mating surfaces.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse exhaust manifold gaskets. Tool numbers : KV10114400 (J-38365)
: KV991J0050 (J-44626)
: Engine front
AWBIA1209GB
Limit : 0.3mm (0.012 in)
PBIC1173E
Revision: November 20132014 Altima NAM

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-155
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
• Install the exhaust manifold nuts in the order as shown (A).
CAUTION:
• Before installing a heated oxygen sensor 2 or air fuel ratio (A /F) sensor 1, clean the exhaust mani-
fold threads using the oxygen sensor thread cleaner tool , and apply anti-seize lubricant.
• Do not over-tighten the air fuel ratio (A/F) senso r 1 or heated oxygen sensors 2. Doing so may
cause damage. :Engine front
ALBIA0237ZZ
Tool numbers : J-43897-18
: J-43897-12
Tool numbers : KV10114400 (J-38365) : KV991J0050 (J-44626)
Revision: November 20132014 Altima NAM