display NISSAN TEANA 2014 Manual Online
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 522 of 4801
![NISSAN TEANA 2014 Manual Online
DAS
ITS CONTROL UNITDAS-89
< ECU DIAGNOSIS INFORMATION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
DTC IndexINFOID:0000000009951644
NOTE:
• The details of time display are as follows:
- CRNT: A malfu NISSAN TEANA 2014 Manual Online
DAS
ITS CONTROL UNITDAS-89
< ECU DIAGNOSIS INFORMATION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
DTC IndexINFOID:0000000009951644
NOTE:
• The details of time display are as follows:
- CRNT: A malfu](/img/5/57390/w960_57390-521.png)
DAS
ITS CONTROL UNITDAS-89
< ECU DIAGNOSIS INFORMATION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
DTC IndexINFOID:0000000009951644
NOTE:
• The details of time display are as follows:
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
• IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now
CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 39, it is fixed to 39 unt il the self-diagnosis results are erased.
Other than CAN communication s ystem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 49, it is fixed to 49 unt il the self-diagnosis results are erased.
NOTE:
With the detection of “U1000” some syst ems do not perform the fail-safe operation.
Systems for fail-safe
• A: Lane Departure Warning (LDW)
• B: Blind Spot Warning (BSW)
• C: Moving Object Detection (MOD)
DTC
CONSULT display Warning lamp Fail-safe
Reference
CONSULT
Lane Departure Warning
Blind Spot Warning
Moving Object Detection
System
C1A03 VHCL SPEED SE CIRC ON ON ON A, B, C DAS-111
C1A04 VDC FAIL ON ON ON A, B, CDAS-112
C1A39 STRG SEN CIR ON ON ON A, B, CDAS-113
NO DTC IS
DETECTED. FURTHER
TESTING
MAY BE RE- QUIRED NO DTC IS DETECTED.
FURTHER TESTING MAY BE REQUIRED ——— — —
U0122 VDC P-RUN DIAG ON ON ON A, B, C DAS-114
U0416 VDC CHECKSUM DIAG ON ON ON A, B, CDAS-115
U0428 STRG SEN CAN CIR 2 ON ON ON A, B, CDAS-116
U1000NOTECAN COMM CIRCUIT ON ON ON A, B, CDAS-117
U1010 CONTROL UNIT (CAN) ON ON ON A, B, C DAS-118
U 111 AREAR CAMERA IMAGE
SIGNAL ON ON ON A, B, C
DAS-119
U1232 ST ANGLE SEN CALIB ON ON ON A, B, C DAS-121
U1305 CAMERA IMAGE CALIB ON ON ON A, B, CDAS-122
U1308 CAMERA CONFIG ON ON ON A, B, CDAS-123
U1309 PUMP UNIT CURRENT ON ON ON A, B, CDAS-124
U130BREAR CAMERA COMM
ERROR ON ON ON A, B, C
DAS-127
U1310 PUMP UNIT CIRCUIT ON ON ON A, B, C DAS-128
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 537 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-104
< BASIC INSPECTION >[LDW]
ACTION TEST
ACTION TEST
DescriptionINFOID:0000000009464737
• Perform action test to verify the customers concern.
• Perform action test and check the syst em o NISSAN TEANA 2014 Manual Online
DAS-104
< BASIC INSPECTION >[LDW]
ACTION TEST
ACTION TEST
DescriptionINFOID:0000000009464737
• Perform action test to verify the customers concern.
• Perform action test and check the syst em o](/img/5/57390/w960_57390-536.png)
DAS-104
< BASIC INSPECTION >[LDW]
ACTION TEST
ACTION TEST
DescriptionINFOID:0000000009464737
• Perform action test to verify the customer's concern.
• Perform action test and check the syst em operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
Inspection ProcedureINFOID:0000000009464738
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-232, "Precautions for Moving Objects Detection"
.
1.CHECK LDW SYSTEM SETTING
1. Start the engine.
2. Check that the LDW system setting can be enabled/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.ACTION TEST FOR LDW
1. Enable the setting of the LDW system on the vehicle information display.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation Action Warning sys-
tems ON indi-
cator Indication on the combination
meter Buzzer
Less than
Approx. 60 km/h (40 MPH) Close to lane marker No action ON —
ALOIA0191GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 542 of 4801
![NISSAN TEANA 2014 Manual Online
DAS
REAR VIEW CAMERA CALIBRATIONDAS-109
< BASIC INSPECTION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
CAUTION:
Make sure that the black/white pattern of the center target is rotated as compared with t NISSAN TEANA 2014 Manual Online
DAS
REAR VIEW CAMERA CALIBRATIONDAS-109
< BASIC INSPECTION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
CAUTION:
Make sure that the black/white pattern of the center target is rotated as compared with t](/img/5/57390/w960_57390-541.png)
DAS
REAR VIEW CAMERA CALIBRATIONDAS-109
< BASIC INSPECTION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
CAUTION:
Make sure that the black/white pattern of the center target is rotated as compared with the left and
right targets.
>> Go to DAS-109, "Work Procedure (Rear View Camera Calibration)"
.
Work Procedure (Rear Vi ew Camera Calibration)INFOID:0000000009464744
CAUTION:
Perform the calibration under the sp ecified vehicle condition (fuel full, no-load, specified tire pressure,
etc.). Refer to DAS-107, "Work Procedure (Preparation)"
.
1.CHECK REAR VIEW CAMERA HEIGHT
Measure the rear view camera height “H”.
>> GO TO 2.
2.REAR VIEW CAMERA CALIBRATION
1. Select “Work Support” on “AVM” with CONSULT.
2. Select “REAR CAMERA ITS”.
3. Select "OK". CAUTION:
• Perform the calibration after the ignition or en gine has been kept on for at least 10 minutes to
stabilize camera.
• Operate CONSULT outside the vehicle, and close al l doors to retain appropriate vehicle altitude.
4. Input the rear view camera height "H", and then touch "APPLY".
5. Confirm that the same value is displayed on the center display.
6. Confirm the following items:
- The target should be accurately placed.
- The vehicle should be stopped.
- The vehicle should be under the specified vehicle condition.
7. Select “Start” to perform calibration.
8. Confirm the displayed item.
- “Completed”: Select “Completion”.
- Otherwise, perform the following services:
ALOIA0192GB
ALOIA0188ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 543 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-110
< BASIC INSPECTION >[LDW]
REAR VIEW CAMERA CALIBRATION
NOTE:
Replace camera unit if “00H Routine not activated” or “10H Writing error” are repeatedly indicated during the
above two NISSAN TEANA 2014 Manual Online
DAS-110
< BASIC INSPECTION >[LDW]
REAR VIEW CAMERA CALIBRATION
NOTE:
Replace camera unit if “00H Routine not activated” or “10H Writing error” are repeatedly indicated during the
above two](/img/5/57390/w960_57390-542.png)
DAS-110
< BASIC INSPECTION >[LDW]
REAR VIEW CAMERA CALIBRATION
NOTE:
Replace camera unit if “00H Routine not activated” or “10H Writing error” are repeatedly indicated during the
above two services are performed.
9. Confirm that “Completed” is displayed and then select “End” to close the calibration procedure.
>> GO TO 3.
3.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of ITS control unit with CONSULT.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repa ir or replace the applicable item. Refer to DAS-
89, "DTC Index".
NO >> GO TO 4.
4.ACTION TEST
Test the system operation by action test. Refer to DAS-104, "Description"
.
>> Work End.
Displayed item Possible cause Service procedure
SUSPENSION —
Temporary malfunction in internal processing of the rear
view camera. Go back to Step 1
00H Routine not ac-
tivated Rear view camera unit malfunction.
Position the target appro-
priately again. Perform
the aiming again. Refer
to DAS-108, "Work Pro-
cedure (Target Setting)".
10H Writing error • Temporary malfunction in internal processing of the
rear view camera.
• Rear view camera malfunction.
X AIMING NG Y
(X: 0 - 7, Y: 1 - 8) —• A target is not-yet-placed.
(The rear view camera cannot detect a target.)
• The position of the rear view camera is not correct.
• Inappropriate work environment.
• Inappropriate vehicle condition. Position the target appro-
priately again. Perform
the aiming again. Refer
to DAS-107, "Work Pro-
cedure (Preparation)".
ABNORMALLY COM-
PLETED —
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 549 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-116
< DTC/CIRCUIT DIAGNOSIS >[LDW]
U0428 STEERING ANGLE SENSOR
U0428 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464755
Diagnosis ProcedureINFOID:0000000009464756
1.ADJUST THE NEUTRAL POSITIO NISSAN TEANA 2014 Manual Online
DAS-116
< DTC/CIRCUIT DIAGNOSIS >[LDW]
U0428 STEERING ANGLE SENSOR
U0428 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464755
Diagnosis ProcedureINFOID:0000000009464756
1.ADJUST THE NEUTRAL POSITIO](/img/5/57390/w960_57390-548.png)
DAS-116
< DTC/CIRCUIT DIAGNOSIS >[LDW]
U0428 STEERING ANGLE SENSOR
U0428 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464755
Diagnosis ProcedureINFOID:0000000009464756
1.ADJUST THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
When U1232 is detected, adjust the neutral position of the steering angle sensor.
>> Perform adjustment of the neutral positi on of the steering angle sensor. Refer to BRC-33, "CON-
SULT Function (ABS)".
DTCDisplay contents of
CONSULT DTC detection condition Possible malfunction factor
U0428 ST ANGLE SENSOR
CALIBRATION [U0428] The neutral position adjustment of the steering angle sen-
sor is incomplete. Adjust neutral position of the steering
angle sensor.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 554 of 4801
![NISSAN TEANA 2014 Manual Online
DAS
U1232 STEERING ANGLE SENSORDAS-121
< DTC/CIRCUIT DIAGNOSIS > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
U1232 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464765
Diagnosis ProcedureINFOID:000000000 NISSAN TEANA 2014 Manual Online
DAS
U1232 STEERING ANGLE SENSORDAS-121
< DTC/CIRCUIT DIAGNOSIS > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
U1232 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464765
Diagnosis ProcedureINFOID:000000000](/img/5/57390/w960_57390-553.png)
DAS
U1232 STEERING ANGLE SENSORDAS-121
< DTC/CIRCUIT DIAGNOSIS > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
U1232 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000009464765
Diagnosis ProcedureINFOID:0000000009464766
1.REGISTER THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
1. Turn the ignition switch ON.
2. Perform registration of the neutral positi on of the steering angle sensor. Refer to DAS-83, "CONSULT
Function (AVM)".
3. Check “Self Diagnostic Result” of “AVM” with CONSULT. Refer to DAS-83, "CONSULT Function (AVM)"
.
Is
“ST ANGLE SEN CALIB” detected?
YES >> GO TO 2.
NO >> Inspection End.
2.CHECK STEERING ANGLE SENSOR
Check steering angle sensor.
Is the inspection result normal?
YES >> Replace ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> Repair or replace malfunctioning parts.
DTC Display contents of
CONSULT DTC detection condition Possible malfunction factor
U1232 ST ANGLE SEN CALIB The neutral position registration of the steering angle sen-
sor cannot finish. • Steering angle sensor
• ITS control unit
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 573 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-140
< SYMPTOM DIAGNOSIS >[LDW]
LDW SYSTEM SETTINGS CANNOT BE T
URNED ON/OFF IN VEHICLE INFOR-
MATION DISPLAY
LDW SYSTEM SETTINGS CANNOT BE TURNED ON/OFF IN VEHICLE IN-
FORMATION DISPLAY
Descript NISSAN TEANA 2014 Manual Online
DAS-140
< SYMPTOM DIAGNOSIS >[LDW]
LDW SYSTEM SETTINGS CANNOT BE T
URNED ON/OFF IN VEHICLE INFOR-
MATION DISPLAY
LDW SYSTEM SETTINGS CANNOT BE TURNED ON/OFF IN VEHICLE IN-
FORMATION DISPLAY
Descript](/img/5/57390/w960_57390-572.png)
DAS-140
< SYMPTOM DIAGNOSIS >[LDW]
LDW SYSTEM SETTINGS CANNOT BE T
URNED ON/OFF IN VEHICLE INFOR-
MATION DISPLAY
LDW SYSTEM SETTINGS CANNOT BE TURNED ON/OFF IN VEHICLE IN-
FORMATION DISPLAY
DescriptionINFOID:0000000009464791
• LDW system setting is not selectable on the navigation screen.
• NOTE:
When the ignition switch is in ACC posit ion, LDW system setting cannot be changed.
- “Lane Departure Warning” is not indicated on the navigation screen.
- The switching between ON and OFF cannot be per formed by operating the navigation system.
- The item of “Lane Departure Warning” on the navigation screen is not active.
• After turning ON the ignition switch or starting t he engine, LDW setting of the navigation system cannot be
selected for several tens of sec onds under the following conditions:
- After replacing AV control unit.
- After erasing connection histor y of the navigation system.
- After erasing self-diagnosis results of AV control unit.
• The LDW or LDP system setting differs from the one set at the previous driving.
NOTE:
Turn OFF the ignition switch and wait for 5 seconds or more.
Diagnosis ProcedureINFOID:0000000009464792
1.CHECK LDW SYSTEM SETTING
1. Start the engine.
2. Check that the LDW system settings is selectable on the navigation screen.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.PERFORM THE SELF-DIAGNOSIS
1. Perform “All DTC Reading” with CONSULT.
2. Check if the DTC is detected in self-diagnosis re sults of “AVM”, “MULTI AV” and “METER/M&A”. Refer to
the following.
-AVM: DAS-89, "DTC Index"
- MULTI AV (with BOSE): AV-328, "DTC Index"
- MULTI AV (without BOSE): AV-231, "DTC Index"
- METER/M&A: MWI-27, "DTC Index"
Is any DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> Inspection End.
3.CHECK DATA MONITOR OF ITS CONTROL UNIT
Check that “LDW SELECT” operates normally in “DATA MONITOR” of “AVM” with CONSULT.
Is the inspection result normal?
YES >> Refer to DAS-83, "CONSULT Function (AVM)".
NO >> GO TO 4.
4.CHECK MULTIFUNCTION SWITCH
Operate the multifunction switch to check that the audio, navigation system, and air conditioner operate prop-
erly.
Is the inspection result normal?
YES >> Replace the ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> Repair or replace malfunctioning parts.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 583 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-150
< SYSTEM DESCRIPTION >[BSW]
COMPONENT PARTS
Component Description
INFOID:0000000009464806
1. Combination meter 2. Vehicle information display 3. BCM (view with combination meter re- moved)
4. NISSAN TEANA 2014 Manual Online
DAS-150
< SYSTEM DESCRIPTION >[BSW]
COMPONENT PARTS
Component Description
INFOID:0000000009464806
1. Combination meter 2. Vehicle information display 3. BCM (view with combination meter re- moved)
4.](/img/5/57390/w960_57390-582.png)
DAS-150
< SYSTEM DESCRIPTION >[BSW]
COMPONENT PARTS
Component Description
INFOID:0000000009464806
1. Combination meter 2. Vehicle information display 3. BCM (view with combination meter re- moved)
4. Blind spot warning indicator RH 5. Blind spot warning indicator LH 6. TCM
7. ECM 8. Warning systems switch 9. Warning systems ON indicator
10. Rear view camera washer control unit 11. Rear view camera air pump motor 12. Rear view camera
13. AV control unit (center display) (with navi- gation system and bose audio system)
Audio unit (center display) (with display
audio system and bose audio system) 14. ITS control unit
(view with center console removed) 15. Steering angle sensor
(view with steeri ng wheel removed)
16. Washer fluid level switch (view with front fascia removed)
Component Description
ITS control unit • Being connected with rear view camera via ITS communication, receives vehicle detection signal
and transmits Blind Spot Warning indicator signal and Blind Spot Warning indicator dimmer sig-
nal to the rear view camera
• Being connected with lane camera unit via ITS communication, receives detected lane condition
signal
• Receives steering angle sensor signal from steering angle sensor via CAN communication
• Judges a Blind Spot Warning indicator ON/OFF state and an approach state to the lane marker,
based on each signal.
• Activates the warning buzzer and warning systems ON indicator
• Transmits Blind Spot Warning ON indicator signal to combination meter via CAN communication
Blind Spot Warning indicator LH/
RH Receives Blind Spot Warning indicator operation signal from rear view camera and turns OFF, turns
ON or blinks
Warning systems switch Inputs the switch signal to ITS control unit
Warning systems ON indicator
(On the warning systems switch) Indicates BSW system status
Rear view camera • Detects the lane marker by the built-in camera
• Transmits detected lane condition signal to ITS control unit
ABS actuator and electric unit
(control unit) • Transmits vehicle speed signal to ITS control unit via CAN communication
• Transmits yaw rate signal/side G sensor signal to ITS control unit via CAN communication
Buzzer (combination meter) Receives buzzer signal from ITS control unit and sounds buzzer.
Combination meter • Turns the Blind Spot Warning indicator ON/OFF according to the signals from the ITS control unit
via CAN communication
• Receives Blind Spot Warning ON indicator signal via CAN communication.
Steering angle sensor Transmits steering angle sensor signal to ITS control unit via CAN communication
BCM • Transmits turn signal indicator to ITS control unit via CAN communication
• Transmits dimmer signal to ITS control unit via CAN communication
ECM Transmits engine speed signal to ITS control unit via CAN communication
TCM Transmits the output shaft speed signal, input speed signal, current gear position signal and shift
position signal to ITS control unit via CAN communication
AV c o n t r o l u n i t
(with navigation system and bose
audio system) Receives the various systems and camera signals via CAN communication and routes them to the
center display
Audio unit
(with display audio system and
bose audio system) Receives the various systems and camera signals and routes them to the center display
Center display Displays the various system screen signals according to the priority level received via CAN com-
munication
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 585 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-152
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000009464807
SYSTEM DIAGRAM
CONTROL UNIT INPUT/OUTPUT SIGNAL ITEM
Control unit receives signals via CAN communication. NISSAN TEANA 2014 Manual Online
DAS-152
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000009464807
SYSTEM DIAGRAM
CONTROL UNIT INPUT/OUTPUT SIGNAL ITEM
Control unit receives signals via CAN communication.](/img/5/57390/w960_57390-584.png)
DAS-152
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000009464807
SYSTEM DIAGRAM
CONTROL UNIT INPUT/OUTPUT SIGNAL ITEM
Control unit receives signals via CAN communication. It al
so detects vehicle conditions that are necessary for
BSW control.
Input Signal Item
Output Signal Item
AWOIA0038GB
Transmit unit Signal name Description
ECM CAN Communication Engine status signal Receive engine status
BCM CAN communication Door open status signal Receive door open status
Light status signal Receive light status
ABS actuator
and electric unit
(control unit) CAN communication Wheel speed signal Receive wheel speed
TCM CAN communication Shift selector position signal Receive shift selector position
Combination
meter CAN communication Moving Object Detection ON/
OFF signal Receive the ON/OFF status for Moving Object Detection
function
Rear view cam-
era NTSC Video signal
Receive Rear View Camera
image from camera for Mov-
ing Object Detection function in ITS controller
Reception unit Signal name Description
Combination
meter CAN communication Buzzer request Transmits a buzzer request signal when the moving
object is detected
Display CAN communication Visual signal request Transmits a visual signal request from ITS Controller
to display Rear View while the shift selector is in R (re-
verse)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 587 of 4801
![NISSAN TEANA 2014 Manual Online
DAS-154
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
control unit performs the control when the following conditions are satisfied:
• When the warning systems switch is turned ON
*.
• When the vehicle dr NISSAN TEANA 2014 Manual Online
DAS-154
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
control unit performs the control when the following conditions are satisfied:
• When the warning systems switch is turned ON
*.
• When the vehicle dr](/img/5/57390/w960_57390-586.png)
DAS-154
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
control unit performs the control when the following conditions are satisfied:
• When the warning systems switch is turned ON
*.
• When the vehicle drives at 32 km/h (20 MPH) or more in the forward direction.
NOTE:
*: When the BSW system setting on the v ehicle information display screen is ON.
• After the operating conditions of warning are satisf ied, the warning continues until the vehicle speed is
reduced below approximately 29 km/h (18 MPH)
• The BSW system may not function properly, depending on the situation.
BULB CHECK ACTION AND FAIL-SAFE INDICATION
*: Blinking cycle when there is a rear view camera blockage condition or lane camera unit high tempera-
ture condition
NOTE:
Time shown in the figure is approximate.
Fail-safe (ITS Control Unit)INFOID:0000000009464808
If a malfunction occurs in each system, ITS control uni t cancels each control, and turns ON the warning lamp
or indicator lamp.
Vehicle condition/Driver ′s operation Blind Spot Warning/
Blind Spot Intervention indicator Warning systems
ON indicator Indication on the combination meter
When DTC is detected OFF ON OFF
→ Orange
Temporary disabled status OFF ON BSW light (white) will blink
When rear view camera needs cleaning OFF ON Unavailable: Clean Rear Camera
When the warning systems switch is
pressed
(When the settings of LDW system and
BSW system on the vehicle information
screen are “OFF”) OFF Blink —
ALOIA0172GB
JSOIA0358GB
System Warning lamp/Indicator lamp Description
Blind Spot Warning (BSW) Blind Spot Warning lamp Cancel
Lane Departure Warning (LDW) Lane Departure Warning indicator Cancel
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM